TP-LINK TL-WDR6500 高清拆解

fit5***

H大，我的WDR3320刷砖了，能帮忙看看还能救不
ttl开机日志：
U-Boot 1.1.4 (Jan 17 2013 - 14:30:14)

U-Boot DB120
Wasp 1.3

DRAM:  64 MB
Flash Manuf Id 0x1, DeviceId0 0x2, DeviceId1 0x15
Flash:  4 MB
Using default environment



U-Boot 1.1.4 (Jan 17 2013 - 14:30:14)

U-Boot DB120
Wasp 1.3

DRAM:  64 MB
Flash Manuf Id 0x1, DeviceId0 0x2, DeviceId1 0x15
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
wasp reset mask:c03300
WASP ----> S27 PHY
GMAC: cfg1 0x80000000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4 :0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :0x10
eth0 up
WASP ----> S27 PHY
GMAC: cfg1 0xf cfg2 0x7214
eth1: ba:be:fa:ce:08:41
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0 :0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :0x10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :0x10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :0x10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :0x10
eth1 up
eth0, eth1
Setting 0xb8116290 to 0x21422d0f
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... Not enough buffer for decompression
LZMA ERROR 1 - must RESET board to recover

主板图

max0***

刚刚入坑，感觉5G信号渣的不行。

一***

一股廉价风

bigh***

这款路由器能改千兆LAN口吗？

星***

大佬能问下最后一张图上为啥空了那么多的孔呢？是官方故意没有上器件么？

星***

bighuang 发表于 2018-1-20 16:46
这款路由器能改千兆LAN口吗？

改了也没用，要大换血的～

星***

fei.aa 发表于 2017-2-23 20:01
flash旁边的R611被我焊掉了，这个要用多大的电阻代替？

要么上显微镜，要么查官方技术文档～

viole***

谢谢楼主分享

i8***

小白路过 ，点赞