|
|
今天试了一试刷OPEN-WRT（潘多拉）
很顺利，32M内存没有任何问题，只是固件不成熟，WIFI有问题。
用OPENWRT刷DD也还是不行，看来32M是不行了。
这是刷openwrt的TTL，回刷到PHICOMM网站下固件就可以了，没有记录TTL。
U-Boot 1.1.3 (Sep 11 2013 - 18:26:23)
Board: Ralink APSoC DRAM: 32 MB
relocate_code Pointer at: 81fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 42
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 256 Mbits SDR
DRAM bus: 16 bit
Total memory: 32 MBytes
Flash component: SPI Flash
Date:Sep 11 2013 Time:18:26:23
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 600 MHZ ####
estimate memory size =32 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 2
0
raspi_read: from:40028 len:6
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (10.10.10.123) ==:10.10.10.123
Input server IP (10.10.10.3) ==:10.10.10.3
Input Linux Kernel filename () == pen.bin
netboot_common, argc= 3
NetTxPacket = 0x81FE4CC0
KSEG1ADDR(NetTxPacket) = 0xA1FE4CC0
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 10.10.10.3; our IP address is 10.10.10.123
Filename 'open.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (00:24:21:f1:43:2b)
Got it
Got ARP REQUEST, return our IP
T Got ARP REQUEST, return our IP
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##################
done
Bytes transferred = 7077888 (6c0000 hex)
NetBootFileXferSize= 006c0000
raspi_erase_write: offs:50000, count:6c0000
raspi_erase: offs:50000 len:6c0000
............................................................................................................
raspi_write: to:50000 len:6c0000
............................................................................................................
raspi_read: from:50000 len:10000
raspi_read: from:60000 len:10000
raspi_read: from:70000 len:10000
raspi_read: from:80000 len:10000
raspi_read: from:90000 len:10000
raspi_read: from:a0000 len:10000
raspi_read: from:b0000 len:10000
raspi_read: from:c0000 len:10000
raspi_read: from:d0000 len:10000
raspi_read: from:e0000 len:10000
raspi_read: from:f0000 len:10000
raspi_read: from:100000 len:10000
raspi_read: from:110000 len:10000
raspi_read: from:120000 len:10000
raspi_read: from:130000 len:10000
raspi_read: from:140000 len:10000
raspi_read: from:150000 len:10000
raspi_read: from:160000 len:10000
raspi_read: from:170000 len:10000
raspi_read: from:180000 len:10000
raspi_read: from:190000 len:10000
raspi_read: from:1a0000 len:10000
raspi_read: from:1b0000 len:10000
raspi_read: from:1c0000 len:10000
raspi_read: from:1d0000 len:10000
raspi_read: from:1e0000 len:10000
raspi_read: from:1f0000 len:10000
raspi_read: from:200000 len:10000
raspi_read: from:210000 len:10000
raspi_read: from:220000 len:10000
raspi_read: from:230000 len:10000
raspi_read: from:240000 len:10000
raspi_read: from:250000 len:10000
raspi_read: from:260000 len:10000
raspi_read: from:270000 len:10000
raspi_read: from:280000 len:10000
raspi_read: from:290000 len:10000
raspi_read: from:2a0000 len:10000
raspi_read: from:2b0000 len:10000
raspi_read: from:2c0000 len:10000
raspi_read: from:2d0000 len:10000
raspi_read: from:2e0000 len:10000
raspi_read: from:2f0000 len:10000
raspi_read: from:300000 len:10000
raspi_read: from:310000 len:10000
raspi_read: from:320000 len:10000
raspi_read: from:330000 len:10000
raspi_read: from:340000 len:10000
raspi_read: from:350000 len:10000
raspi_read: from:360000 len:10000
raspi_read: from:370000 len:10000
raspi_read: from:380000 len:10000
raspi_read: from:390000 len:10000
raspi_read: from:3a0000 len:10000
raspi_read: from:3b0000 len:10000
raspi_read: from:3c0000 len:10000
raspi_read: from:3d0000 len:10000
raspi_read: from:3e0000 len:10000
raspi_read: from:3f0000 len:10000
raspi_read: from:400000 len:10000
raspi_read: from:410000 len:10000
raspi_read: from:420000 len:10000
raspi_read: from:430000 len:10000
raspi_read: from:440000 len:10000
raspi_read: from:450000 len:10000
raspi_read: from:460000 len:10000
raspi_read: from:470000 len:10000
raspi_read: from:480000 len:10000
raspi_read: from:490000 len:10000
raspi_read: from:4a0000 len:10000
raspi_read: from:4b0000 len:10000
raspi_read: from:4c0000 len:10000
raspi_read: from:4d0000 len:10000
raspi_read: from:4e0000 len:10000
raspi_read: from:4f0000 len:10000
raspi_read: from:500000 len:10000
raspi_read: from:510000 len:10000
raspi_read: from:520000 len:10000
raspi_read: from:530000 len:10000
raspi_read: from:540000 len:10000
raspi_read: from:550000 len:10000
raspi_read: from:560000 len:10000
raspi_read: from:570000 len:10000
raspi_read: from:580000 len:10000
raspi_read: from:590000 len:10000
raspi_read: from:5a0000 len:10000
raspi_read: from:5b0000 len:10000
raspi_read: from:5c0000 len:10000
raspi_read: from:5d0000 len:10000
raspi_read: from:5e0000 len:10000
raspi_read: from:5f0000 len:10000
raspi_read: from:600000 len:10000
raspi_read: from:610000 len:10000
raspi_read: from:620000 len:10000
raspi_read: from:630000 len:10000
raspi_read: from:640000 len:10000
raspi_read: from:650000 len:10000
raspi_read: from:660000 len:10000
raspi_read: from:670000 len:10000
raspi_read: from:680000 len:10000
raspi_read: from:690000 len:10000
raspi_read: from:6a0000 len:10000
raspi_read: from:6b0000 len:10000
raspi_read: from:6c0000 len:10000
raspi_read: from:6d0000 len:10000
raspi_read: from:6e0000 len:10000
raspi_read: from:6f0000 len:10000
raspi_read: from:700000 len:10000
Done!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: PandoraBox Linux-3.4.54
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 963026 Bytes = 940.5 kB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:eb1d2
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32
Starting kernel ...
PandoraBox For Ralink SoC. Copyright 2005-2013 Lintel<lintel.huang@gmail.com>
Linux Kernel started...
THIS IS ASIC
[ 0.000000] Linux version 3.4.54 (lintel@lintel-ThinkPad-T430) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #6 Wed Jul 24 22:49:04 CST 2013
[ 0.000000] MediaTek MT7620N CPU:600MHz, Bus:150MHz Uart:40MHz
[ 0.000000] Boot form:SPI FLASH
[ 0.000000] MIPS CPU sleep mode enabled.
[ 0.000000] Detecting memory...32 MB!
[ 0.000000] PCIE: bypass PCIe DLL.
[ 0.000000] PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
[ 0.000000] disable all power about PCIe
[ 0.000000] PCIE: PLL power down for MT7620N
[ 0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS1,57600n8 board=MW305R rootfstype=squashfs
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=0001600f
[ 0.000000] Readback ErrCtl register=0001600f
[ 0.000000] Memory: 29364k/32768k available (2317k kernel code, 3404k reserved, 383k data, 160k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=16, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] MTK/Ralink System Tick Counter init... cd:80295170, m:214748, s:32
[ 0.000000] console [ttyS1] enabled
[ 0.010000] Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.090000] Mount-cache hash table entries: 512
[ 0.100000] NET: Registered protocol family 16
[ 0.110000] MIPS: machine is Mercury MW305R
[ 0.120000] Ralink Board GPIO_MODE init:
[ 0.120000] I2C:GPIO
[ 0.130000] SPI_REFCLK:GPIO
[ 0.130000] UART_F:GPIO
[ 0.140000] GPIO_MODE_REGs: 0x1a311d
[ 0.140000] ralink_register_flash:SPI Flash.
[ 0.150000] General GPIO Driver for MediaTek MT7620N Board . 漏 2005-2012 lintel<lintel.huang@gmail.com>
[ 0.160000] GPIO maped at address:0xb0000600.
[ 0.160000] gpiochip_add: registered GPIOs 0 to 23 on device: MT7620-GPIO0
[ 0.170000] GPIO maped at address:0xb0000600.
[ 0.170000] gpiochip_add: registered GPIOs 24 to 39 on device: MT7620-GPIO1
[ 0.180000] GPIO maped at address:0xb0000600.
[ 0.180000] gpiochip_add: registered GPIOs 40 to 71 on device: MT7620-GPIO2
[ 0.190000] GPIO maped at address:0xb0000600.
[ 0.190000] gpiochip_add: registered GPIOs 72 to 95 on device: MT7620-GPIO3
[ 0.200000] RALINK_GPIOMODE = 1a311d
[ 0.200000] RALINK_GPIOMODE = 18311d
[ 0.300000] PPLL_CFG1=0x4010000
[ 0.310000] MT7620 PPLL unlock
[ 0.320000] bio: create slab <bio-0> at 0
[ 0.330000] Switching to clocksource Ralink external timer
[ 0.340000] NET: Registered protocol family 2
[ 0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.360000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.380000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.390000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.400000] TCP: reno registered
[ 0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.420000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.430000] NET: Registered protocol family 1
[ 0.440000] Ralink SoC clocks api init.
[ 0.450000] Ralink GPIODEV resource maped.
[ 0.460000] RT3xxx EHCI/OHCI init.
[ 0.490000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.500000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) 漏 2001-2006 Red Hat, Inc.
[ 0.520000] msgmni has been set to 57
[ 0.530000] io scheduler noop registered
[ 0.540000] io scheduler deadline registered (default)
[ 0.550000] io scheduler cfq registered
[ 0.560000] Ralink DMA Engine API Enable .
[ 0.570000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.580000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
[ 0.590000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
[ 0.610000] Enable Ralink GDMA Controller Module
[ 0.620000] GDMA IP Version=3
[ 0.630000] loop: module loaded
[ 0.640000] Ralink SPI flash Driver for PandoraBox.
[ 0.650000] deice id : ef 40 17 0 0 (40170000)
[ 0.660000] W25Q64BV(ef 40170000) (8192 Kbytes)
[ 0.670000] mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
[ 0.690000] Creating 5 MTD partitions on "raspi":
[ 0.700000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.710000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.730000] 0x000000040000-0x000000050000 : "Factory"
[ 0.740000] 0x000000000000-0x000000800000 : "fullflash"
[ 0.750000] 0x000000050000-0x000001000000 : "firmware"
[ 0.760000] mtd: partition "firmware" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
[ 0.780000] Creating 2 MTD partitions on "raspi":
[ 0.790000] 0x000000050000-0x000000140000 : "kernel"
[ 0.810000] 0x000000140000-0x000001000000 : "rootfs"
[ 0.820000] mtd: partition "rootfs" extends beyond the end of device "raspi" -- size truncated to 0x6c0000
[ 0.840000] mtd: partition "rootfs" set to be root filesystem
[ 0.850000] mtd: partition "rootfs_data" created automatically, ofs=6F0000, len=110000
[ 0.860000] 0x0000006f0000-0x000000800000 : "rootfs_data"
[ 0.880000] rdm_major = 253
[ 0.880000] EEPROM:Read from [Factory] offset 0x28,length 0x6.
[ 0.900000] SMACCR1 -- : 0x0000f0eb
[ 0.900000] SMACCR0 -- : 0xd0362884
[ 0.910000] Ralink APSoC Ethernet Driver Initilization. v3.0 64 rx/tx descriptors allocated, mtu = 1500!
[ 0.930000] EEPROM:Read from [Factory] offset 0x28,length 0x6.
[ 0.940000] SMACCR1 -- : 0x0000f0eb
[ 0.950000] SMACCR0 -- : 0xd0362884
[ 0.960000] PROC INIT OK!
[ 0.960000] Ralink APSoC Hardware Watchdog Timer
[ 0.970000] sdhci: Secure Digital Host Controller Interface driver
[ 0.980000] sdhci: Copyright(c) Pierre Ossman
[ 0.990000] SDHC Interface init.
[ 1.000000] mtk-sd: MediaTek MT76xx MSDC Driver
[ 1.010000] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.020000] TCP: cubic registered
[ 1.030000] NET: Registered protocol family 17
[ 1.040000] 8021q: 802.1Q VLAN Support v1.8
[ 1.060000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[ 1.070000] Freeing unused kernel memory: 160k freed
##### MediaTek MT76xx ESW VLAN Partition(12345) #####
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
Special Tag Disabled
switch reg write offset=2610, value=81000000
12345
switch reg write offset=2014, value=10001
switch reg write offset=2114, value=10002
switch reg write offset=2214, value=10003
switch reg write offset=2314, value=10004
switch reg write offset=2414, value=10005
switch reg write offset=2514, value=10006
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
[ 3.440000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -
Please press Enter to activate this console. [ 8.180000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[ 8.200000] Backport based on wireless-testing.git master-2013-02-22
[ 8.210000] compat.git: wireless-testing.git
[ 8.370000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.380000] cfg80211: World regulatory domain updated:
[ 8.390000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.400000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.420000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.440000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.450000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.470000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.810000] SCSI subsystem initialized
[ 8.980000] usbcore: registered new interface driver usbfs
[ 8.990000] usbcore: registered new interface driver hub
[ 9.000000] usbcore: registered new device driver usb
[ 9.570000] usbcore: registered new interface driver rtl8187
[ 9.600000] usbcore: registered new interface driver rt2800usb
[ 9.970000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 10.310000] PPP generic driver version 2.4.2
[ 10.440000] gpiodev: gpio device registered with major 254
[ 10.620000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.810000] NET: Registered protocol family 24
[ 10.990000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 11.020000] rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
[ 11.040000] rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
[ 11.080000] rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
[ 11.110000] rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
[ 11.120000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 11.130000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.140000] usb usb1: Product: Ralink EHCI Host Controller
[ 11.160000] usb usb1: Manufacturer: Linux 3.4.54 ehci_hcd
[ 11.170000] usb usb1: SerialNumber: rt3xxx
[ 11.180000] hub 1-0:1.0: USB hub found
[ 11.180000] hub 1-0:1.0: 1 port detected
[ 11.280000] nf_conntrack version 0.5.0 (461 buckets, 1844 max)
[ 11.740000] xt_time: kernel timezone is -0000
[ 12.550000] rt2860v2_ap: module license 'Proprietary' taints kernel.
[ 12.570000] Disabling lock debugging due to kernel taint
[ 12.630000] PanddoraBox AP Driver version-2.7.1.6(Jul 24 2013 18:08:57).
[ 12.750000] usbcore: registered new interface driver usblp
[ 12.780000] Initializing USB Mass Storage driver...
[ 12.790000] usbcore: registered new interface driver usb-storage
[ 12.800000] USB Mass Storage support registered.
[ 12.910000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 12.950000] fuse init (API version 7.18)
[ 14.640000] EEPROM:Read from [Factory] offset 0x0,length 0x200.
[ 15.180000] 0x1300 = 00064300
[ 18.730000] Raeth v3.0 (Tasklet,SkbRecycle)
[ 18.740000]
[ 18.740000] phy_tx_ring = 0x00f02000, tx_ring = 0xa0f02000
[ 18.740000]
[ 18.740000] phy_rx_ring0 = 0x00f03000, rx_ring0 = 0xa0f03000
[ 18.740000] SMACCR1 -- : 0x0000f0eb
[ 18.740000] SMACCR0 -- : 0xd0362884
[ 18.790000] ESW: Link Status Changed - Port1 Link UP
[ 18.800000] CDMA_CSG_CFG = 81000000
[ 18.800000] GDMA1_FWD_CFG = 20710000
[ 18.820000] device eth2.1 entered promiscuous mode
[ 18.830000] device eth2 entered promiscuous mode
[ 18.850000] br-lan: port 1(eth2.1) entered forwarding state
[ 18.860000] br-lan: port 1(eth2.1) entered forwarding state
[ 18.890000] device eth2.2 entered promiscuous mode
[ 18.900000] br-lan: port 2(eth2.2) entered forwarding state
[ 18.910000] br-lan: port 2(eth2.2) entered forwarding state
[ 18.960000] device eth2.3 entered promiscuous mode
[ 18.970000] br-lan: port 3(eth2.3) entered forwarding state
[ 18.980000] br-lan: port 3(eth2.3) entered forwarding state
[ 19.080000] device eth2.4 entered promiscuous mode
[ 19.090000] br-lan: port 4(eth2.4) entered forwarding state
[ 19.100000] br-lan: port 4(eth2.4) entered forwarding state
[ 20.860000] br-lan: port 1(eth2.1) entered forwarding state
[ 20.910000] br-lan: port 2(eth2.2) entered forwarding state
[ 20.980000] br-lan: port 3(eth2.3) entered forwarding state
[ 21.100000] br-lan: port 4(eth2.4) entered forwarding state
[ 21.360000] Started WatchDog Timer.
[ 21.360000] Started WatchDog Timer.
[ 23.710000] EEPROM:Read from [Factory] offset 0x0,length 0x200.
[ 24.240000] 0x1300 = 00064300
[ 25.430000] device ra0 entered promiscuous mode
[ 25.440000] br-lan: port 5(ra0) entered forwarding state
[ 25.450000] br-lan: port 5(ra0) entered forwarding state
[ 27.450000] br-lan: port 5(ra0) entered forwarding state
|
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
显身卡
发表于 2014-3-11 21:46