求解，TP740nV5刚刚好好的，一会就不行了。

nainiu888

今天早晨改好的，中午用着还行，多拨也试了，最多6拨，下载速度最高4MB/S。下载了一步电影和CF游戏，就把电源拔了，刚刚在插上电就不能启动了，有时像没内存是的，5个灯一直亮，有时能能启动，但没启动起来，灯就全灭，没反映了。。为什么呀这是？？
内存型号是：HY5DU121622CTP-J
FLASH:WINBOND W25Q64BVSIG 8M的
TT信息：
第一次，没启动起来
U-Boot 1.1.4 (Aug 27 2011 - 10:39:39)

AP121-2MB (ar9330) U-boot

DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.3.3 (zeaxion@zeaxion-desktop) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Mon May 21 17:13:10 CST 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR741ND-v4 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61776k/65536k available (2087k kernel code, 3760k reserved, 399k data, 200k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:48
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
[    0.540000] bio: create slab <bio-0> at 0
[    0.540000] Switching to clocksource MIPS
[    0.550000] NET: Registered protocol family 2
[    0.550000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.560000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.570000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.570000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.580000] TCP reno registered
[    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] NET: Registered protocol family 1
[    0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.620000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.630000] msgmni has been set to 120
[    0.630000] io scheduler noop registered
[    0.640000] io scheduler deadline registered (default)
[    0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.650000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.660000] console [ttyATH0] enabled, bootconsole disabled
[    0.660000] console [ttyATH0] enabled, bootconsole disabled
[    0.670000] m25p80 spi0.0: found s25fl064k, expected m25p80
[    0.670000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.680000] 5 tp-link partitions found on MTD device spi0.0
[    0.680000] Creating 5 MTD partitions on "spi0.0":
[    0.690000] 0x000000000000-0x000000020000 : "u-boot"
[    0.690000] 0x000000020000-0x0000000fd8e0 : "kernel"
[    0.700000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.710000] 0x0000000fd8e0-0x0000007f0000 : "rootfs"
[    0.720000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.730000] mtd: partition "rootfs" set to be root filesystem
[    0.730000] mtd: partition "rootfs_data" created automatically, ofs=6C0000, len=130000
[    0.740000] 0x0000006c0000-0x0000007f0000 : "rootfs_data"
[    0.750000] 0x0000007f0000-0x000000800000 : "art"
[    0.750000] 0x000000020000-0x0000007f0000 : "firmware"
[    1.000000] ag71xx_mdio: probed
[    1.000000] eth0: Atheros AG71xx at 0xba000000, irq 5
[    1.590000] eth0: Found an AR7240/AR9330 built-in switch
[    2.820000] eth1: Atheros AG71xx at 0xb9000000, irq 4
[    3.430000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    3.430000] TCP westwood registered
[    3.440000] NET: Registered protocol family 17
[    3.440000] 8021q: 802.1Q VLAN Support v1.8
[    3.450000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    3.460000] Freeing unused kernel memory: 200k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[   10.640000] JFFS2 notice: (424) jffs2_build_xattr_subsystem: complete building xattr subsystem, 3 of xdatum (1 unchecked, 2 orphan) and 109 of xref (0 dead, 78 orphan) found.
switching to jffs2
- init -

Please press Enter to activate this console. [   13.690000] Compat-wireless backport release: compat-wireless-2012-04-17-1-r31449
[   13.700000] Backport based on wireless-testing.git master-2012-04-17
[   13.740000] cfg80211: Calling CRDA to update world regulatory domain
[   14.310000] cfg80211: World regulatory domain updated:
[   14.310000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   14.320000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.330000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   14.330000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   14.340000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.350000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
到这就没了。

nainiu888

第二次，没启动起来，4LAN灯加系统灯亮，没反映。



U-Boot 1.1.4 (Aug 27 2011 - 10:39:39)

AP121-2MB (ar9330) U-boot

DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.3.3 (zeaxion@zeaxion-desktop) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Mon May 21 17:13:10 CST 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR741ND-v4 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61776k/65536k available (2087k kernel code, 3760k reserved, 399k data, 200k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:48
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
[    0.540000] bio: create slab <bio-0> at 0
[    0.540000] Switching to clocksource MIPS
[    0.550000] NET: Registered protocol family 2
[    0.550000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.560000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.570000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.570000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.580000] TCP reno registered
[    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] NET: Registered protocol family 1
[    0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.620000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.630000] msgmni has been set to 120
[    0.630000] io scheduler noop registered
[    0.640000] io scheduler deadline registered (default)
[    0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.650000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.660000] console [ttyATH0] enabled, bootconsole disabled
[    0.660000] console [ttyATH0] enabled, bootconsole disabled
[    0.670000] m25p80 spi0.0: found s25fl064k, expected m25p80
[    0.670000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.680000] 5 tp-link partitions found on MTD device spi0.0
[    0.680000] Creating 5 MTD partitions on "spi0.0":
[    0.690000] 0x000000000000-0x000000020000 : "u-boot"
[    0.690000] 0x000000020000-0x0000000fd8e0 : "kernel"
[    0.700000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.710000] 0x0000000fd8e0-0x0000007f0000 : "rootfs"
[    0.720000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.730000] mtd: partition "rootfs" set to be root filesystem
[    0.730000] mtd: partition "rootfs_data" created automatically, ofs=6C0000, len=130000
[    0.740000] 0x0000006c0000-0x0000007f0000 : "rootfs_data"
[    0.750000] 0x0000007f0000-0x000000800000 : "art"
[    0.750000] 0x000000020000-0x0000007f0000 : "firmware"
[    1.000000] ag71xx_mdio: probed
[    1.000000] eth0: Atheros AG71xx at 0xba000000, irq 5
[    1.590000] eth0: Found an AR7240/AR9330 built-in switch
[    2.820000] eth1: Atheros AG71xx at 0xb9000000, irq 4
[    3.430000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    3.430000] TCP westwood registered
[    3.440000] NET: Registered protocol family 17
[    3.440000] 8021q: 802.1Q VLAN Support v1.8
[    3.450000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    3.460000] Freeing unused kernel memory: 200k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[   10.590000] JFFS2 notice: (424) jffs2_build_xattr_subsystem: complete building xattr subsystem, 3 of xdatum (1 unchecked, 2 orphan) and 109 of xref (0 dead, 78 orphan) found.
switching to jffs2
- init -

Please press Enter to activate this console. [   13.630000] Compat-wireless backport release: compat-wireless-2012-04-17-1-r31449
[   13.630000] Backport based on wireless-testing.git master-2012-04-17
[   13.670000] cfg80211: Calling CRDA to update world regulatory domain
[   14.210000] cfg80211: World regulatory domain updated:
[   14.210000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   14.220000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.220000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   14.230000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   14.240000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.250000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.530000] SCSI subsystem initialized
[   14.790000] usbcore: registered new interface driver usbfs
[   14.800000] usbcore: registered new interface driver hub
[   14.800000] usbcore: registered new device driver usb
[   15.630000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[   15.630000] cfg80211: Calling CRDA for country: US
[   15.650000] Button Hotplug driver version 0.4.1
[   15.830000] cfg80211: Regulatory domain changed to country: US
[   15.840000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   15.850000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   15.850000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   15.860000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.870000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.880000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.880000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   16.660000] PPP generic driver version 2.4.2
[   16.700000] PPP MPPE Compression module registered
[   16.940000] GRE over IPv4 demultiplexor driver
[   16.970000] GRE over IPv4 tunneling driver
[   17.370000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   17.670000] NET: Registered protocol family 24
[   17.950000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   17.960000] ath79-ehci ar933x-ehci: Atheros built-in EHCI controller
[   17.960000] ath79-ehci ar933x-ehci: new USB bus registered, assigned bus number 1
[   18.000000] ath79-ehci ar933x-ehci: irq 3, io mem 0x1b000000
[   18.020000] ath79-ehci ar933x-ehci: USB 2.0 started, EHCI 1.00
[   18.020000] hub 1-0:1.0: USB hub found
[   18.020000] hub 1-0:1.0: 1 port detected
[   18.060000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)
[   18.560000] usb 1-1: new full-speed USB device number 2 using ath79-ehci
[   19.150000] usb 1-1: device descriptor read/64, error -71
[   19.490000] xt_time: kernel timezone is -0000
[   19.630000] usb 1-1: device descriptor read/64, error -71
[   19.900000] usb 1-1: new full-speed USB device number 3 using ath79-ehci
[   20.040000] xt_opendpi 0.1 (OpenDPI wrapper module).
[   20.150000] arp_tables: (C) 2002 David S. Miller
[   20.480000] usb 1-1: device descriptor read/64, error -71
[   20.590000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   20.680000] uhci_hcd: USB Universal Host Controller Interface driver
[   21.080000] usbcore: registered new interface driver usbserial
[   21.080000] USB Serial support registered for generic
[   21.130000] usb 1-1: device descriptor read/64, error -71
[   21.360000] usb 1-1: new full-speed USB device number 4 using ath79-ehci
[   21.840000] usb 1-1: device not accepting address 4, error -71
[   21.960000] usb 1-1: new full-speed USB device number 5 using ath79-ehci

nainiu888

[   22.440000] usb 1-1: device not accepting address 5, error -71
[   22.440000] hub 1-0:1.0: unable to enumerate USB device on port 1
[   22.450000] usbcore: registered new interface driver usbserial_generic
[   22.450000] usbserial: USB Serial Driver core
[   22.550000] Initializing USB Mass Storage driver...
[   22.550000] usbcore: registered new interface driver usb-storage
[   22.560000] USB Mass Storage support registered.
[   22.580000] usbcore: registered new interface driver ums-alauda
[   22.610000] usbcore: registered new interface driver ums-cypress
[   22.630000] usbcore: registered new interface driver ums-datafab
[   22.650000] usbcore: registered new interface driver ums-freecom
[   22.670000] usbcore: registered new interface driver ums-isd200
[   22.700000] usbcore: registered new interface driver ums-jumpshot
[   22.720000] usbcore: registered new interface driver ums-karma
[   22.740000] usbcore: registered new interface driver ums-sddr09
[   22.770000] usbcore: registered new interface driver ums-sddr55
[   22.790000] usbcore: registered new interface driver ums-usbat
[   22.950000] usbcore: registered new interface driver usbhid
[   22.950000] usbhid: USB HID core driver
[   23.090000] fuse init (API version 7.18)
[   30.190000] device wlan0 entered promiscuous mode
[   33.370000] device wlan0 left promiscuous mode
[   33.370000] br-lan: port 1(wlan0) entered disabled state
[   33.790000] device wlan0 entered promiscuous mode
[   34.630000] device eth0 entered promiscuous mode
[   35.350000] device eth1 entered promiscuous mode
[   38.460000] BUG: Bad page map in process S45firewall  pte:0000000c pmd:83fbe000
没了。

ZHIZAI100

换uboot试试。看上去怎么是2M的uboot？？

byteway110

u盘坏了，换一个吧

byteway110

u盘坏了，换一个吧，usb1.1的还不是正牌货

nainiu888

ZHIZAI100 发表于 2013-6-19 10:13
换uboot试试。看上去怎么是2M的uboot？？

用的这个固件http://www.anywlan.com/thread-145497-1-1.html

nainiu888

byteway110 发表于 2013-6-19 19:57
u盘坏了，换一个吧，usb1.1的还不是正牌货

没插U盘的应该是固件带的驱动。

mourny

你这个显示的是4M啊，换个U-BOOT试试