|
|
楼主 |
发表于 2014-11-3 19:41
|
显示全部楼层
内核日志
[ 0.000000] Linux version 3.10.58 (user@guoguopc-lan) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42868) ) #5 Sat Nov 1 15:54:59 CST 2014
[ 0.000000] MyLoader: sysp=f11e1ffe, boardp=d43cc0a6, parts=b8dd2687
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 3
[ 0.000000] Clocks: CPU:600.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 803169d0, node_mem_map 81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=QIHOO-C301 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot),64k(u-boot-env),64k(devdata),64k(devconf),15744k(firmware_backup),64k(warm_start),64k(action_image_config),64k(radiocfg);spi0.1:15360k(firmware),1024k(privatedata) rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126120k/131072k available (2261k kernel code, 4952k reserved, 605k data, 268k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.070000] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] MIPS: machine is Qihoo 360 C301
[ 0.100000] registering PCI controller with io_map_base unset
[ 0.540000] bio: create slab <bio-0> at 0
[ 0.540000] PCI host bridge to bus 0000:00
[ 0.550000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.550000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.560000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.560000] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[ 0.560000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x001fffff 64bit]
[ 0.560000] pci 0000:00:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[ 0.560000] pci 0000:00:00.0: supports D1 D2
[ 0.560000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.560000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[ 0.570000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[ 0.570000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.580000] Switching to clocksource MIPS
[ 0.580000] NET: Registered protocol family 2
[ 0.590000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.590000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.600000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.600000] TCP: reno registered
[ 0.610000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.610000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.620000] NET: Registered protocol family 1
[ 0.620000] PCI: CLS 0 bytes, default 32
[ 0.640000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.640000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.650000] msgmni has been set to 246
[ 0.660000] io scheduler noop registered
[ 0.660000] io scheduler deadline registered (default)
[ 0.670000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.700000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.700000] console [ttyS0] enabled, bootconsole disabled
[ 0.710000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.720000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.730000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.730000] 8 cmdlinepart partitions found on MTD device spi0.0
[ 0.740000] Creating 8 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.750000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.760000] 0x000000050000-0x000000060000 : "devdata"
[ 0.770000] 0x000000060000-0x000000070000 : "devconf"
[ 0.770000] 0x000000070000-0x000000fd0000 : "firmware_backup"
[ 0.780000] 0x000000fd0000-0x000000fe0000 : "warm_start"
[ 0.790000] 0x000000fe0000-0x000000ff0000 : "action_image_config"
[ 0.790000] 0x000000ff0000-0x000001000000 : "radiocfg"
[ 0.800000] m25p80 spi0.1: found mx25l12805d, expected m25p80
[ 0.810000] m25p80 spi0.1: mx25l12805d (16384 Kbytes)
[ 0.810000] 2 cmdlinepart partitions found on MTD device spi0.1
[ 0.820000] Creating 2 MTD partitions on "spi0.1":
[ 0.820000] 0x000000000000-0x000000f00000 : "firmware"
[ 0.880000] 2 seama-fw partitions found on MTD device firmware
[ 0.880000] 0x000000000000-0x000000140000 : "kernel"
[ 0.890000] 0x000000140000-0x000000f00000 : "rootfs"
[ 0.890000] mtd: device 10 (rootfs) set to be root filesystem
[ 0.900000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.910000] 0x000000b60000-0x000000f00000 : "rootfs_data"
[ 0.910000] 0x000000f00000-0x000001000000 : "privatedata"
[ 0.940000] libphy: ag71xx_mdio: probed
[ 1.490000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.530000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 3.080000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[ 3.090000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 3.100000] TCP: cubic registered
[ 3.110000] NET: Registered protocol family 17
[ 3.110000] 8021q: 802.1Q VLAN Support v1.8
[ 3.130000] VFS: Mounted root (squashfs filesystem) readonly on device 31:10.
[ 3.140000] Freeing unused kernel memory: 268K (8032d000 - 80370000)
[ 9.050000] usbcore: registered new interface driver usbfs
[ 9.050000] usbcore: registered new interface driver hub
[ 9.060000] usbcore: registered new device driver usb
[ 9.100000] SCSI subsystem initialized
[ 9.110000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.120000] ehci-platform: EHCI generic platform driver
[ 9.120000] ehci-platform ehci-platform: EHCI Host Controller
[ 9.130000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 9.140000] ehci-platform ehci-platform: TX-TX IDP fix enabled
[ 9.150000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 9.170000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 9.170000] hub 1-0:1.0: USB hub found
[ 9.180000] hub 1-0:1.0: 1 port detected
[ 9.180000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.190000] usbcore: registered new interface driver usb-storage
[ 9.570000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 9.870000] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 9.890000] scsi0 : usb-storage 1-1:1.0
[ 10.890000] scsi 0:0:0:0: Direct-Access FUJITSU MHT2040AH 006C PQ: 0 ANSI: 0 CCS
[ 10.900000] sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 10.910000] sd 0:0:0:0: [sda] Write Protect is off
[ 10.910000] sd 0:0:0:0: [sda] Mode Sense: 00 14 00 00
[ 10.910000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.000000] sda: sda1 < sda5 >
[ 11.020000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 12.080000] eth0: link up (1000Mbps/Full duplex)
[ 15.220000] jffs2: notice: (372) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 42 of xref (0 dead, 2 orphan) found.
[ 15.370000] jffs2: notice: (369) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 42 of xref (0 dead, 2 orphan) found.
[ 15.620000] eth0: link down
[ 17.490000] end_request: critical target error, dev sda, sector 0
[ 17.500000] JBD2: recovery failed
[ 17.500000] EXT4-fs (sda5): error loading journal
[ 23.130000] NET: Registered protocol family 10
[ 23.180000] tun: Universal TUN/TAP device driver, 1.6
[ 23.190000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 23.210000] l2tp_core: L2TP core driver, V2.0
[ 23.210000] l2tp_netlink: L2TP netlink interface
[ 23.230000] sit: IPv6 over IPv4 tunneling driver
[ 23.240000] gre: GRE over IPv4 demultiplexor driver
[ 23.240000] ip_gre: GRE over IPv4 tunneling driver
[ 23.260000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 23.380000] nf_conntrack version 0.5.0 (1974 buckets, 7896 max)
[ 23.410000] Netfilter messages via NETLINK v0.30.
[ 23.430000] ip_set: protocol 6
[ 23.780000] ufsd: module license 'Commercial product' taints kernel.
[ 23.790000] Disabling lock debugging due to kernel taint
[ 23.830000] ufsd:: trace mask set to 0000000f
[ 23.830000] ufsd: driver (lke_8.9.0 lke_8.9.0_22, LBD=ON, delalloc, ioctl, bdi, sd2, fua, tr) loaded at 86f00000
[ 23.830000] NTFS support included
[ 23.830000] Big endian platform
[ 23.830000] optimized: speed
[ 23.830000] Build_for__ASUS_PRODUCTS_005_k2.6.22.15_2013-11-20_lke_8.9.0_r217400_b3
[ 23.830000]
[ 23.910000] Loading modules backported from Linux version master-2014-10-08-0-g0275925
[ 23.910000] Backport generated by backports.git backports-20140905-1-gde42785
[ 23.950000] cfg80211: Calling CRDA to update world regulatory domain
[ 23.950000] cfg80211: World regulatory domain updated:
[ 23.960000] cfg80211: DFS Master region: unset
[ 23.960000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 23.970000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 23.980000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 23.990000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 24.000000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 24.010000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 24.010000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 24.020000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 24.030000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 24.130000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 24.440000] ath10k_pci 0000:00:00.0: pci irq legacy interrupts 0 irq_mode 0 reset_mode 0
[ 24.460000] Linux video capture interface: v2.00
[ 24.540000] u32 classifier
[ 24.540000] input device check on
[ 24.550000] Actions configured
[ 24.560000] Mirror/redirect action on
[ 24.650000] Failed to load ipt action
[ 24.710000] fuse init (API version 7.22)
[ 24.850000] usbcore: registered new interface driver cdc_acm
[ 24.850000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 24.870000] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1
[ 24.890000] usbcore: registered new interface driver cpia2
[ 24.950000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[ 24.950000] Hooking IMQ before NAT on PREROUTING.
[ 24.960000] Hooking IMQ after NAT on POSTROUTING.
[ 25.020000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 25.140000] usbcore: registered new interface driver p54usb
[ 25.170000] usbcore: registered new interface driver Philips webcam
[ 25.250000] usbcore: registered new interface driver rtl8187
[ 25.310000] usbcore: registered new interface driver ums-alauda
[ 25.320000] usbcore: registered new interface driver ums-cypress
[ 25.320000] usbcore: registered new interface driver ums-datafab
[ 25.360000] usbcore: registered new interface driver ums-freecom
[ 25.390000] usbcore: registered new interface driver ums-isd200
[ 25.400000] usbcore: registered new interface driver ums-jumpshot
[ 25.400000] usbcore: registered new interface driver ums-karma
[ 25.420000] usbcore: registered new interface driver ums-sddr09
[ 25.440000] usbcore: registered new interface driver ums-sddr55
[ 25.460000] usbcore: registered new interface driver ums-usbat
[ 25.480000] usbcore: registered new interface driver usblp
[ 25.520000] usbcore: registered new interface driver usbserial
[ 25.550000] usbcore: registered new interface driver usbserial_generic
[ 25.550000] usbserial: USB Serial support registered for generic
[ 25.580000] usbcore: registered new interface driver uvcvideo
[ 25.580000] USB Video Class driver (1.1.1)
[ 25.740000] xt_time: kernel timezone is -0000
[ 25.780000] usbcore: registered new interface driver ath9k_htc
[ 25.800000] usbcore: registered new interface driver carl9170
[ 25.810000] usbcore: registered new interface driver cdc_ether
[ 25.820000] usbcore: registered new interface driver ch341
[ 25.820000] usbserial: USB Serial support registered for ch341-uart
[ 25.850000] gspca_main: v2.14.0 registered
[ 25.870000] usbcore: registered new interface driver pl2303
[ 25.890000] usbserial: USB Serial support registered for pl2303
[ 25.910000] PPP generic driver version 2.4.2
[ 25.910000] PPP MPPE Compression module registered
[ 25.920000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
[ 25.930000] NET: Registered protocol family 24
[ 25.950000] PPTP driver version 0.8.5
[ 25.950000] usbcore: registered new interface driver rndis_host
[ 25.970000] usbcore: registered new interface driver rt2500usb
[ 26.010000] usbcore: registered new interface driver rt2800usb
[ 26.090000] ath: EEPROM regdomain: 0x0
[ 26.090000] ath: EEPROM indicates default country code should be used
[ 26.090000] ath: doing EEPROM country->regdmn map search
[ 26.090000] ath: country maps to regdmn code: 0x3a
[ 26.090000] ath: Country alpha2 being used: US
[ 26.090000] ath: Regpair used: 0x3a
[ 26.110000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 26.120000] cfg80211: Calling CRDA for country: US
[ 26.120000] cfg80211: Regulatory domain changed to country: US
[ 26.130000] cfg80211: DFS Master region: FCC
[ 26.130000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 26.140000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 26.150000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 26.160000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 26.170000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 26.180000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 26.190000] ieee80211 phy1: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
[ 26.220000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 26.260000] usbcore: registered new interface driver option
[ 26.260000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 26.290000] usbcore: registered new interface driver rtl8192cu
[ 27.240000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2-00082-4-2 api 3 htt 2.1
[ 27.250000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 0 testmode 1
[ 27.850000] ath: EEPROM regdomain: 0x0
[ 27.850000] ath: EEPROM indicates default country code should be used
[ 27.850000] ath: doing EEPROM country->regdmn map search
[ 27.850000] ath: country maps to regdmn code: 0x3a
[ 27.850000] ath: Country alpha2 being used: US
[ 27.850000] ath: Regpair used: 0x3a
[ 38.170000] jffs2: notice: (2271) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 38.270000] end_request: critical target error, dev sda, sector 0
[ 38.280000] JBD2: recovery failed
[ 38.280000] EXT4-fs (sda5): error loading journal
[ 42.820000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 42.820000] device eth0 entered promiscuous mode
[ 42.830000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 42.850000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 43.920000] eth0: link up (1000Mbps/Full duplex)
[ 43.920000] br-lan: port 1(eth0) entered forwarding state
[ 43.930000] br-lan: port 1(eth0) entered forwarding state
[ 43.930000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 43.960000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 44.040000] cfg80211: Calling CRDA for country: CN
[ 44.080000] cfg80211: Regulatory domain changed to country: CN
[ 44.090000] cfg80211: DFS Master region: FCC
[ 44.090000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 44.100000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2300 mBm), (N/A)
[ 44.110000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2100 mBm), (N/A)
[ 44.120000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2100 mBm), (0 s)
[ 44.130000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2100 mBm), (N/A)
[ 44.140000] cfg80211: (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
[ 44.150000] cfg80211: (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4400 mBm), (N/A)
[ 44.150000] cfg80211: (63720000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
[ 45.630000] eth1: link up (100Mbps/Full duplex)
[ 45.630000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 45.930000] br-lan: port 1(eth0) entered forwarding state
[ 47.270000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
[ 49.940000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 49.970000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 49.990000] device wlan0 entered promiscuous mode
[ 49.990000] device wlan1 entered promiscuous mode
[ 51.280000] br-lan: port 3(wlan1) entered forwarding state
[ 51.280000] br-lan: port 3(wlan1) entered forwarding state
[ 51.290000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 53.280000] br-lan: port 3(wlan1) entered forwarding state
[ 65.690000] br-lan: port 2(wlan0) entered forwarding state
[ 65.690000] br-lan: port 2(wlan0) entered forwarding state
[ 65.700000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 67.690000] br-lan: port 2(wlan0) entered forwarding state
|
|
楼主: 崴@崴
/1 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2014-11-3 17:54
显身卡
