有没有大神能简单解答一下如何根据ttl输出的信息书写dts和dtsi文件？

xykz

rt，编译了mt7620a lenovo y1的固件，能刷在小米mini上，但是5G连上无法取得ip地址，和潘多拉魔盒对比后觉得可能是无法读取正确的eeprom信息。

小米的论坛上有人放出了完整的ttl读取信息，请问如何根据这个改写dts和dtsi文件呢？

1. U-Boot 1.1.3 (Jul 10 2014 - 18:28:53)
   
2. Board: Ralink APSoC DRAM:  128 MB
   
3. relocate_code Pointer at: 87f68000
   
4. enable ephy clock...done. rf reg 29 = 5
   
5. SSC disabled.
   
6. spi_wait_nsec: 29
   
7. spi device id: c2 20 18 c2 20 (2018c220)
   
8. find flash: MX25L12805D
   
9. raspi_read: from:30000 len:1000
   
10. raspi_read: from:30000 len:1000
    
11. ============================================
    
12. Ralink UBoot Version: 4.2.S.1
    
13. --------------------------------------------
    
14. ASIC 7620_MP (Port5<->None)
    
15. DRAM component: 1024 Mbits DDR, width 16
    
16. DRAM bus: 16 bit
    
17. Total memory: 128 MBytes
    
18. Flash component: SPI Flash
    
19. Date:Jul 10 2014  Time:18:28:53
    
20. ============================================
    
21. icache: sets:512, ways:4, linesz:32 ,total:65536
    
22. dcache: sets:256, ways:4, linesz:32 ,total:32768
    
23. ##### The CPU freq = 580 MHZ ####
    
24. estimate memory size =128 Mbytes
    
25. Please choose the operation:
    
26.    1: Load system code to SDRAM via TFTP.
    
27.    2: Load system code then write to Flash via TFTP.
    
28.    3: Boot system code via Flash (default).
    
29.    4: Entr boot command line interface.
    
30.    7: Load Boot Loader code then write to Flash via Serial.
    
31.    9: Load Boot Loader code then write to Flash via TFTP.
    
32. 
    
33. 3: System Boot system code via Flash.
    
34. Try to boot OS1
    
35. raspi_read: from:30000 len:10000
    
36. Erasing SPI Flash...
    
37. raspi_erase: offs:30000 len:10000
    
38. .
    
39. Writing to SPI Flash...
    
40. raspi_write: to:30000 len:10000
    
41. .
    
42. done
    
43. ## Booting image at bc050000 ...
    
44. raspi_read: from:50000 len:40
    
45.    Image Name:   MIPS OpenWrt Linux-2.6.36
    
46.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
    
47.    Data Size:    1431406 Bytes =  1.4 MB
    
48.    Load Address: 80000000
    
49.    Entry Point:  80000000
    
50. raspi_read: from:50040 len:15d76e
    
51.    Verifying Checksum ... OK
    
52.    Uncompressing Kernel Image ... OK
    
53. fac_flag 0xffffffff
    
54. commandline uart_en=0 factory_mode=0 mem=128m
    
55. No initrd
    
56. ## Transferring control to Linux (at address 80000000) ...
    
57. ## Giving linux memsize in MB, 128
    
58. Starting kernel ...
    
59. 
    
60. LINUX started...
    
61. THIS IS ASIC
    
62. Linux version 2.6.36 (szy @ shenzhiyong-ct) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012:49 CST 2014
    
63. The CPU feqenuce set to 580 MHz
    
64. PCIE: bypass PCIe DLL.
    
65. PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
    
66. disable all power about PCIe
    
67. CPU revision is: 00019650 (MIPS 24Kc)
    
68. Software DMA cache coherency
    
69. Determined physical RAM map:
    
70. memory: 04000000  @  00000000 (usable)
    
71. User-defined physical RAM map:
    
72. memory: 08000000  @  00000000 (usable)
    
73. Zone PFN ranges:
    
74.   Normal   0x00000000 -> 0x00008000
    
75. Movable zone start PFN for each node
    
76. early_node_map[1] active PFN ranges
    
77.     0: 0x00000000 -> 0x00008000
    
78. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
    
79. Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock5 uart_en=0 factory_mode=0 mem=128m
    
80. PID hash table entries: 512 (order: -1, 2048 bytes)
    
81. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    
82. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    
83. Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
    
84. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
    
85. Writing ErrCtl register=0002f2f6
    
86. Readback ErrCtl register=0002f2f6
    
87. Memory: 125540k/131072k available (3004k kernel code, 5532k reserved, 950k data, 160k init, 0k highmem)
    
88. NR_IRQS:128
    
89. console [ttyS1] enabled
    
90. Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
    
91. pid_max: default: 32768 minimum: 301
    
92. Mount-cache hash table entries: 512
    
93. NET: Registered protocol family 16
    
94. RALINK_GPIOMODE = 1a131c
    
95. RALINK_GPIOMODE = 18131c
    
96. PPLL_CFG1=0xe70000
    
97. MT7620 PPLL lock
    
98. PPLL_DRV =0x80080504
    
99. start PCIe register access
    
100. RALINK_RSTCTRL = 2400000
     
101. RALINK_CLKCFG1 = 75afffc0
     
102. *************** MT7620 PCIe RC mode *************
     
103. PCIE0 enabled
     
104. init_rt2880pci done
     
105. bio: create slab <bio-0> at 0
     
106. SCSI subsystem initialized
     
107. usbcore: registered new interface driver usbfs
     
108. usbcore: registered new interface driver hub
     
109. usbcore: registered new device driver usb
     
110. pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
     
111. pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
     
112. pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
     
113. pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
     
114. pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
     
115. pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
     
116. pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] (PCI address [0x20000000-0x200fffff]
     
117. pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
     
118. pci 0000:00:00.0: PCI bridge to [bus 01-01]
     
119. pci 0000:00:00.0:   bridge window [io  disabled]
     
120. pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
     
121. pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
     
122. BAR0 at slot 0 = 0
     
123. bus=0x0, slot = 0x0
     
124. res[0]->start = 0
     
125. res[0]->end = 0
     
126. res[1]->start = 20200000
     
127. res[1]->end = 2020ffff
     
128. res[2]->start = 0
     
129. res[2]->end = 0
     
130. res[3]->start = 0
     
131. res[3]->end = 0
     
132. res[4]->start = 0
     
133. res[4]->end = 0
     
134. res[5]->start = 0
     
135. res[5]->end = 0
     
136. bus=0x1, slot = 0x0
     
137. res[0]->start = 20000000
     
138. res[0]->end = 200fffff
     
139. res[1]->start = 0
     
140. res[1]->end = 0
     
141. res[2]->start = 0
     
142. res[2]->end = 0
     
143. res[3]->start = 0
     
144. res[3]->end = 0
     
145. res[4]->start = 0
     
146. res[4]->end = 0
     
147. res[5]->start = 0
     
148. res[5]->end = 0
     
149. Switching to clocksource MIPS
     
150. NET: Registered protocol family 2
     
151. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
     
152. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
     
153. TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
     
154. TCP: Hash tables configured (established 4096 bind 4096)
     
155. TCP reno registered
     
156. UDP hash table entries: 256 (order: 0, 4096 bytes)
     
157. UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
     
158. NET: Registered protocol family 1
     
159. RT3xxx EHCI/OHCI init.
     
160. squashfs: version 4.0 (2009/01/31) Phillip Lougher
     
161. JFFS2 version 2.2 (NAND) (SUMMARY) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
     
162. fuse init (API version 7.15)
     
163. msgmni has been set to 245
     
164. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
     
165. io scheduler noop registered (default)
     
166. Ralink gpio driver initialized
     
167. Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
     
168. serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
     
169. serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
     
170. init reset module!
     
171. brd: module loaded
     
172. deice id : c2 20 18 c2 20 (2018c220)
     
173. MX25L12805D(c2 2018c220) (16384 Kbytes)
     
174. mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 65536
     
175. Creating 11 MTD partitions on "raspi":
     
176. 0x000000000000-0x000001000000 : "ALL"
     
177. 0x000000000000-0x000000030000 : "Bootloader"
     
178. 0x000000030000-0x000000040000 : "Config"
     
179. 0x000000040000-0x000000050000 : "Factory"
     
180. 0x000000050000-0x000000cd0000 : "OS1"
     
181. mtd: try split OS1 partition
     
182. mtd: split_firmware
     
183. mtd: firmware_partition->size   0xc80000
     
184. mtd: firmware_partition->offset 0x50000
     
185. mtd: uimage_len 1431470
     
186. mtd: rootfs_partition->size   0xb22852
     
187. mtd: rootfs_partition->offset 0x1ad7ae
     
188. mtd: partition "rootfs" created automatically, ofs=1AD7AE, len=B22852
     
189. 0x0000001ad7ae-0x000000cd0000 : "rootfs"
     
190. mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
     
191. mtd: rootfs_len 10889298
     
192. 0x000000cd0000-0x000000ed0000 : "OS2"
     
193. 0x000000ed0000-0x000000fd0000 : "overlay"
     
194. 0x000000fd0000-0x000000fe0000 : "crash"
     
195. 0x000000fe0000-0x000000ff0000 : "reserved"
     
196. 0x000000ff0000-0x000001000000 : "Bdata"
     
197. 0x000000050000-0x000000ff0000 : "firmware"
     
198. rdm_major = 253
     
199. SMACCR1 -- : 0x00008cbe
     
200. SMACCR0 -- : 0xbe401279
     
201. Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
     
202. SMACCR1 -- : 0x00008cbe
     
203. SMACCR0 -- : 0xbe401279
     
204. PROC INIT OK!
     
205. PPP generic driver version 2.4.2
     
206. PPP MPPE Compression module registered
     
207. NET: Registered protocol family 24
     
208. PPTP driver version 0.8.5
     
209. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
     
210. rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
     
211. rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
     
212. rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
     
213. rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
     
214. hub 1-0:1.0: USB hub found
     
215. hub 1-0:1.0: 1 port detected
     
216. ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
     
217. rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
     
218. rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
     
219. rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
     
220. hub 2-0:1.0: USB hub found
     
221. hub 2-0:1.0: 1 port detected
     
222. usbcore: registered new interface driver cdc_acm
     
223. cdc_acm: v0.26:USB Abstract Control Model ** adapters
     
224. Initializing USB Mass Storage driver...
     
225. usbcore: registered new interface driver usb-storage
     
226. USB Mass Storage support registered.
     
227. usbcore: registered new interface driver usbserial
     
228. USB Serial support registered for generic
     
229. usbcore: registered new interface driver usbserial_generic
     
230. usbserial: USB Serial Driver core
     
231. USB Serial support registered for pl2303
     
232. usbcore: registered new interface driver pl2303
     
233. pl2303: Prolific PL2303 USB to serial adaptor driver
     
234. USB Serial support registered for TI USB 3410 1 port adapter
     
235. USB Serial support registered for TI USB 5052 2 port adapter
     
236. usbcore: registered new interface driver ti_usb_3410_5052
     
237. ti_usb_3410_5052: v0.10:TI USB 3410/5052 Serial Driver
     
238. nf_conntrack version 0.5.0 (1961 buckets, 7844 max)
     
239. IPVS: Registered protocols ()
     
240. IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
     
241. IPVS: ipvs loaded.
     
242. GRE over IPv4 demultiplexor driver
     
243. ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
     
244. TCP cubic registered
     
245. NET: Registered protocol family 10
     
246. NET: Registered protocol family 17
     
247. L2TP core driver, V2.0
     
248. PPPoL2TP kernel driver, V2.0
     
249. L2TP netlink interface
     
250. 802.1Q VLAN Support v1.8 Ben Greear <greearb @ candelatech.com>
     
251. All bugs added by David S. Miller <davem @ redhat.com>
     
252. VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
     
253. Freeing unused kernel memory: 160k freed
     
254. Raeth v3.0 (Tasklet,SkbRecycle)
     
255. phy_tx_ring = 0x0751c000, tx_ring = 0xa751c000
     
256. phy_rx_ring0 = 0x0751d000, rx_ring0 = 0xa751d000
     
257. SMACCR1 -- : 0x00008cbe
     
258. SMACCR0 -- : 0xbe401279
     
259. CDMA_CSG_CFG = 81000000
     
260. GDMA1_FWD_CFG = 20710000
     
261. - preinit -
     
262. - regular preinit -
     
263. JFFS2 notice: (93) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 uncheref (0 dead, 0 orphan) found.
     
264. switching to jffs2
     
265. jffs2 not ready yet; using ramdisk
     
266. Unlocking OS1 ...
     
267. Thu Jan  1 13:00:00 UTC 1970
     
268. fix epoch time 1970-01-01 13:00:00 ok.
     
269. - init -
     
270. ra2880stop()...Done
     
271. Free TX/RX Ring Memory!
     
272. init started: BusyBox v1.19.4 (2014-07-10 18:25:02 CST)
     
273. Please press Enter to activate this console. rcS S boot: INFO: rc script run time limit to 65 seconds.
     
274. Thu Jan  1 13:00:00 UTC 1970 pre-system-up[156]:  *
     
275. Thu Jan  1 13:00:00 UTC 1970 pre-system-up[156]:  ******* R1CM/mips *******
     
276. Button Hotplug driver version 0.4.1
     
277. NTFS driver 2.1.29 [Flags: R/O MODULE].
     
278. GRE over IPv4 tunneling driver
     
279. register rt2860
     
280. 
     
281. === pAd = c0902000, size = 1811424 ===
     
282. <-- RTMPAllocTxRxRingMemory, Status=0
     
283. <-- RTMPAllocAdapterBlock, Status=0
     
284. pAd->CSRBaseAddress =0xc0800000, csr_addr=0xc0800000!
     
285. device_id =0x7662
     
286. ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
     
287. RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
     
288. RtmpEepromGetDefault::e2p_dafault=2
     
289. NVM is FLASH mode
     
290. mt7620: module license 'unspecified' taints kernel.
     
291. Disabling lock debugging due to kernel taint
     
292. 
     
293. === pAd = c0ebb000, size = 953216 ===
     
294. <-- RTMPAllocTxRxRingMemory, Status=0
     
295. <-- RTMPAllocAdapterBlock, Status=0
     
296. AP Driver version-2.7.1.6
     
297. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: INFO: loading exist /etc/config/network.
     
298. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: config interface 'loopback'
     
299. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option ifname 'lo'
     
300. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option proto 'static'
     
301. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option ipaddr '127.0.0.1'
     
302. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option netmask '255.0.0.0'
     
303. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: config interface 'lan'
     
304. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option ifname 'eth0.1'
     
305. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option type 'bridge'
     
306. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option proto 'static'
     
307. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option netmask '255.255.255.0'
     
308. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option ipaddr '192.168.31.1'
     
309. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: config interface 'wan'
     
310. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option proto 'pppoe'
     
311. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option mtu '1480'
     
312. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option special '0'
     
313. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option username '02298540935'
     
314. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option password '98540935'
     
315. Thu Jan  1 21:00:07 CST 1970 netconfig[446]: option ifname 'eth0.2'
     
316. Raeth v3.0 (Tasklet,SkbRecycle)
     
317. phy_tx_ring = 0x06629000, tx_ring = 0xa6629000
     
318. phy_rx_ring0 = 0x0662b000, rx_ring0 = 0xa662b000
     
319. SMACCR1 -- : 0x00008cbe
     
320. SMACCR0 -- : 0xbe401279
     
321. CDMA_CSG_CFG = 81000000
     
322. GDMA1_FWD_CFG = 20710000
     
323. device eth0.1 entered promiscuous mode
     
324. device eth0 entered promiscuous mode
     
325. br-lan: port 1(eth0.1) entering learning state
     
326. br-lan: port 1(eth0.1) entering learning state
     
327. ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
     
328. br-lan: port 1(eth0.1) entering forwarding state
     
329. RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=wl0!
     
330. ==>rlt_wlan_chip_onoff(): OnOff:0, Reset= 0, pAd->WlanFunCtrl:0x20b, Reg-WlanFunCtrl=0x20b
     
331. register rt2860
     
332. 
     
333. === pAd = c1982000, size = 1811424 ===
     
334. <-- RTMPAllocTxRxRingMemory, Status=0
     
335. <-- RTMPAllocAdapterBlock, Status=0
     
336. pAd->CSRBaseAddress =0xc1880000, csr_addr=0xc1880000!
     
337. device_id =0x7662
     
338. ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x208
     
339. RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
     
340. RtmpEepromGetDefault::e2p_dafault=2
     
341. NVM is FLASH mode
     
342. build time = [20140408060640a
     
343. ]
     
344. rom patch for E3 IC
     
345. platform = [ALPS]
     
346. hw/sw version = [8a 10 8a 10 ]
     
347. patch version = [00000010]
     
348. FW Version:0.0.00 Build:1
     
349. Build Time:201403201049____
     
350. fw for E3 IC
     
351. RX[0] DESC a6e7e000 size = 4096
     
352. RX[1] DESC a6e7f000 size = 4096
     
353. E2pAccessMode=2
     
354. cfg_mode=14
     
355. cfg_mode=14
     
356. wmode_band_equal(): Band Not Equal!
     
357. Key1Str is Invalid key length(0) or Type(0)
     
358. Key2Str is Invalid key length(0) or Type(0)
     
359. Key3Str is Invalid key length(0) or Type(0)
     
360. Key4Str is Invalid key length(0) or Type(0)
     
361. 1. Phy Mode = 49
     
362. get_chl_grp:illegal channel (167)
     
363. get_chl_grp:illegal channel (167)
     
364. get_chl_grp:illegal channel (169)
     
365. get_chl_grp:illegal channel (169)
     
366. get_chl_grp:illegal channel (171)
     
367. get_chl_grp:illegal channel (171)
     
368. get_chl_grp:illegal channel (173)
     
369. get_chl_grp:illegal channel (173)
     
370. Country Region from e2p = ffff
     
371. mt76x2_get_external_lna_gain::LNA type=0x11, BLNAGain=0x0, ALNAGain0=0xffffff82, ALNAGain1=0x0, ALNAGai
     
372. 2. Phy Mode = 49
     
373. 3. Phy Mode = 49
     
374. andes_pci_fw_init
     
375. 0x1300 = 00073200
     
376. AntCfgInit: primary/secondary ant 0/1
     
377. andes_load_cr:cr_type(2)
     
378. ChipStructAssign(): MT76x2 hook !
     
379. RTMPSetPhyMode: channel is out of range, use first channel=0
     
380. MCS Set = ff ff 00 00 01
     
381. TX0 power compensation = 0x38
     
382. TX1 power compensation = 0x38
     
383. Jan  1 21:00:24 TaskMonitor[Server][584]: task fork_failed,can not find the task[sysapihttpd]
     
384. Jan  1 21:00:24 TaskMonitor[Server][584]: task[nginx: master process /usr/sbin/sysapihttpd -c /tmp/sysanf] start failed!
     
385. mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=157, HT-CentCh=159, VHT-CentCh=155
     
386. APStartUp(): AP Set CentralFreq at 155(Prim=157, HT-CentCh=159, VHT-CentCh=155, BBP_BW=2)
     
387. mt76x2_calibration(channel = 155)
     
388. The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
     
389. Main bssid = 8c:be:be:40:12:7b
     
390. mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x27, hi_lna1 = 0x27
     
391. mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x27, hi_lna1 = 0x27
     
392. original vga value(chain0) = 5c
     
393. original vga value(chain1) = 5c
     
394. <==== rt28xx_init, Status=0
     
395. RTMPDrvOpen(1):Check if PDMA is idle!
     
396. RTMPDrvOpen(2):Check if PDMA is idle!
     
397. mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=157, HT-CentCh=159, VHT-CentCh=155
     
398. APStartUp(): AP Set CentralFreq at 155(Prim=157, HT-CentCh=159, VHT-CentCh=155, BBP_BW=2)
     
399. mt76x2_calibration(channel = 155)
     
400. The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
     
401. device wl0 entered promiscuous mode
     
402. br-lan: port 2(wl0) entering learning state
     
403. br-lan: port 2(wl0) entering learning state
     
404. RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=wl1!
     
405. 
     
406. === pAd = c2015000, size = 953216 ===
     
407. <-- RTMPAllocTxRxRingMemory, Status=0
     
408. <-- RTMPAllocAdapterBlock, Status=0
     
409. AP Driver version-2.7.1.6
     
410. Enabling Ralink HW NAT Module ...
     
411. Ralink HW NAT Module Enabled!
     
412. br-lan: port 2(wl0) entering forwarding state
     
413. Jan  1 21:00:38 PPOC/messagingagent[584]: Thrift: Thu Jan  1 21:00:38 1970 TNonblockingServer: using lid epoll
     
414. Jan  1 21:00:38 PPOC/messagingagent[584]: Thrift: Thu Jan  1 21:00:38 1970 TNonblocking: IO thread #0 r
     
415. Jan  1 21:00:38 PPOC/messagingagent[584]: I0101 21:00:38.958582  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
416. Jan  1 21:00:38 PPOC/messagingagent[584]: Thrift: Thu Jan  1 21:00:38 1970 TNonblocking: IO thread #0 r
     
417. Jan  1 21:00:38 PPOC/messagingagent[584]: Thrift: Thu Jan  1 21:00:38 1970 TNonblockingServer: IO threa
     
418. Jan  1 21:00:38 PPOC/messagingagent[584]: I0101 21:00:38.958395  2861 MQTTClient.cpp:204] Waiting for ct
     
419. RX DESC a6dc9000  size = 2048
     
420. Key1Str is Invalid key length(0) or Type(0)
     
421. Key2Str is Invalid key length(0) or Type(0)
     
422. Key3Str is Invalid key length(0) or Type(0)
     
423. Key4Str is Invalid key length(0) or Type(0)
     
424. 1. Phy Mode = 9
     
425. 2. Phy Mode = 9
     
426. E2PROM: D0 target power=0x1e
     
427. E2PROM: 40 MW Power Delta= 0
     
428. 3. Phy Mode = 9
     
429. AntCfgInit: primary/secondary ant 0/1
     
430. D1 = 0, D2 = 6, CalCode = 14 !!!
     
431. RT6352_Temperature_Init : BBPR49 = 0x0
     
432. RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff6
     
433. Current Temperature from BBP_R49=0xfffffff6
     
434. RT6352_TssiTableAdjust: upper_bound = 0x7F decimal: 127
     
435. RT6352_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128
     
436. *** RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -1 -1 -1 -128 -1 -1
     
437. - -1 - -1 -1 -1 -1 -1 -1 -1, offset=-10, tuning=0
     
438. RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -11 -11 -11 -128 -11 -11 - -11 - -11 -11 -11 -11 -11 -10
     
439. mp_temperature=0xfffffff4, step = -2
     
440. E2PROM: G Tssi[-7 .. +7] = -128 -11 -11 -11 -128 -11 -11 - -11 - -11 -11 -11 -11 -11 -11 -11, offset=-1
     
441. TX BW Filter Calibration !!!
     
442. RX BW Filter Calibration !!!
     
443. LOFT Calibration Done!
     
444. IQCalibration Start!
     
445. IQCalibration Done! CH = 0, (gain= d, phase= 2)
     
446. IQCalibration Start!
     
447. IQCalibration Done! CH = 1, (gain= 1, phase= 0)
     
448. TX IQ Calibration Done!
     
449. Change as Normal Mode(0x8171d)
     
450. After Change, now GPIO_MODE value is 0x8171d
     
451. RT6352_Init_ExtPA_ExtLNA: Enable Ext-LNA.
     
452. RT6352_Init_ExtPA_ExtLNA: Init Ext-LNA BBP.
     
453. bAutoTxAgcG = 0
     
454. RTMPSetPhyMode: channel is out of range, use first channel=0
     
455. MCS Set = ff ff 00 00 01
     
456. SYNC - BBP R4 to 20MHz.l
     
457. Jan  1 21:00:45 PPOC/messagingagent[584]: I0101 21:00:45.062155  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
458. Jan  1 21:00:45 PPOC/messagingagent[584]: E0101 21:00:45.065260  2862 HTTPRequest.cpp:175] HTTP Requesterror: Couldn't resolve host 'api.gorouter.info', url: http : / / api.gorouter.info/config, params: , metho
     
459. Jan  1 21:00:45 PPOC/messagingagent[584]: E0101 21:00:45.065675  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
460. Jan  1 21:00:45 PPOC/messagingagent[584]: I0101 21:00:45.065835  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
461. Jan  1 21:00:45 PPOC/messagingagent[584]: E0101 21:00:45.068715  2862 HTTPRequest.cpp:175] HTTP Requesterror: Couldn't resolve host 'api.gorouter.info', url: http : / / api.gorouter.info/config, params: , metho
     
462. Jan  1 21:00:45 PPOC/messagingagent[584]: E0101 21:00:45.069019  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
463. SYNC - BBP R4 to 20MHz.l
     
464. SYNC - BBP R4 to 20MHz.l
     
465. SYNC - BBP R4 to 20MHz.l
     
466. SYNC - BBP R4 to 20MHz.l
     
467. SYNC - BBP R4 to 20MHz.l
     
468. SYNC - BBP R4 to 20MHz.l
     
469. SYNC - BBP R4 to 20MHz.l
     
470. SYNC - BBP R4 to 20MHz.l
     
471. Main bssid = 8c:be:be:40:12:7a
     
472. <==== rt28xx_init, Status=0
     
473. 0x1300 = 00064320
     
474. rcS S boot: INFO: rcS S boot timing 49 seconds.
     
475. Thu Jan  1 21:00:50 CST 1970 INFO: rcS S boot timing 49 seconds.
     
476. rcS S boot: system type(R1CM/2): SQUASH/65535
     
477. Thu Jan  1 21:00:50 CST 1970 system type(R1CM/2): SQUASH/65535
     
478. rcS S boot: ROOTFS: /dev/root on / type squashfs (ro,relatime)
     
479. Thu Jan  1 21:00:50 CST 1970 ROOTFS: /dev/root on / type squashfs (ro,relatime)
     
480. Thu Jan  1 21:00:50 CST 1970 boot_check[3740]: INFO: Wireless OK
     
481. <btnd> main(),L78:
     
482. <btnd> hook_gpio(),L22:
     
483. mknod: /dev/gpio: File exists
     
484. <btnd> hook_gpio(),L39: thread: pid=3859,irq=30
     
485. device wl1 entered promiscuous mode
     
486. br-lan: port 3(wl1) entering learning state
     
487. br-lan: port 3(wl1) entering learning state
     
488. br-lan: port 3(wl1) entering forwarding state
     
489. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.245188  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
490. Jan  1 21:01:29 PPOC/messagingagent[584]: I0101 21:01:29.245346  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
491. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.248524  2862 HTTPRequest.cpp:175] HTTP Requesterror: Couldn't resolve host 'api.gorouter.info', url: http : / / api.gorouter.info/config, params: , metho
     
492. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.248825  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
493. Jan  1 21:01:29 PPOC/messagingagent[584]: I0101 21:01:29.248981  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
494. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.252196  2862 HTTPRequest.cpp:175] HTTP Requesterror: Couldn't resolve host 'api.gorouter.info', url: http : / / api.gorouter.info/config, params: , metho
     
495. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.252498  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
496. Jan  1 21:01:29 PPOC/messagingagent[584]: I0101 21:01:29.252670  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
497. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.255874  2862 HTTPRequest.cpp:175] HTTP Requesterror: Couldn't resolve host 'api.gorouter.info', url: http : / / api.gorouter.info/config, params: , metho
     
498. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.256177  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
499. Jan  1 21:01:29 PPOC/messagingagent[584]: I0101 21:01:29.256335  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
500. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.267198  2862 HTTPRequest.cpp:175] HTTP Requesterror: Couldn't resolve host 'api.gorouter.info', url: http : / / api.gorouter.info/config, params: , metho
     
501. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.267499  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
502. Jan  1 21:01:29 PPOC/messagingagent[584]: I0101 21:01:29.267655  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
503. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.270903  2862 HTTPRequest.cpp:175] HTTP Requesterror: Couldn't resolve host 'api.gorouter.info', url: http : / / api.gorouter.info/config, params: , metho
     
504. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.271206  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
505. Jan  1 21:01:29 PPOC/messagingagent[584]: I0101 21:01:29.271365  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
506. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.274625  2862 HTTPRequest.cpp:175] HTTP Requesterror: Couldn't resolve host 'api.gorouter.info', url: http : / / api.gorouter.info/config, params: , metho
     
507. Jan  1 21:01:29 PPOC/messagingagent[584]: E0101 21:01:29.274934  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
508. Jan  1 21:02:01 smartcontroller[3382]: [SMART_CONTROLLER INFO Scene.cpp:131]Scene actions dirty
     
509. Jan  1 21:02:01 smartcontroller[3382]: [SMART_CONTROLLER INFO AlarmObject.cpp:168]Alarm timer time: 23:
     
510. Jan  1 13:18:32 PPOC/messagingagent[584]: E0101 13:18:32.431034  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
511. Jan  1 13:18:32 PPOC/messagingagent[584]: I0101 13:18:32.431192  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
512. Jan  1 13:18:32 PPOC/messagingagent[584]: E0101 13:18:32.434416  2862 HTTPRequest.cpp:175] HTTP Requesterror: Couldn't resolve host 'api.gorouter.info', url: http : / / api.gorouter.info/config, params: , metho
     
513. Jan  1 13:18:32 PPOC/messagingagent[584]: E0101 13:18:32.434718  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
514. Jan  1 13:18:32 PPOC/messagingagent[584]: I0101 13:18:32.434874  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
515. Jan  1 13:18:32 PPOC/messagingagent[584]: E0101 13:18:32.438114  2862 HTTPRequest.cpp:175] HTTP Requesterror: Couldn't resolve host 'api.gorouter.info', url: http : / / api.gorouter.info/config, params: , metho
     
516. Jan  1 13:18:32 PPOC/messagingagent[584]: E0101 13:18:32.438415  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
517. Jan  1 13:20:58 PPOC/messagingagent[584]: E0101 13:20:58.923163  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
518. Jan  1 13:20:58 PPOC/messagingagent[584]: I0101 13:20:58.923319  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
519. Jan  1 13:20:58 PPOC/messagingagent[584]: E0101 13:20:58.926587  2862 HTTPRequest.cpp:175] HTTP Requesterror: Couldn't resolve host 'api.gorouter.info', url: http : / / api.gorouter.info/config, params: , metho
     
520. Jan  1 13:20:58 PPOC/messagingagent[584]: E0101 13:20:58.926887  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
521. Jan  1 13:20:58 PPOC/messagingagent[584]: I0101 13:20:58.927045  2862 HTTPRequest.cpp:123] Executing HTpi.gorouter.info/config, params: , method: GET)
     
522. Jan  1 13:20:58 PPOC/messagingagent[584]: E0101 13:20:58.931617  2862 HTTPRequest.cpp:175] HTTP Requesterror: Couldn't resolve host 'api.gorouter.info', url: http : / / api.gorouter.info/config, params: , metho
     
523. Jan  1 13:20:58 PPOC/messagingagent[584]: E0101 13:20:58.931917  2862 RemoteConfig.cpp:75] Unable to fel: http : / / api.gorouter.info/config, error code: HTTP error, error message: Couldn't resolve host 'api.g
     
524. usb 2-1: new full speed USB device using rt3xxx-ohci and address 2
     
525. scsi0 : usb-storage 2-1:1.0
     
526. scsi 0:0:0:0: Direct-Access     USB2.0   CARD-READER      1.01 PQ: 0 ANSI: 2
     
527. sd 0:0:0:0: [sda] 1002496 512-byte logical blocks: (513 MB/489 MiB)
     
528. sd 0:0:0:0: [sda] Write Protect is off
     
529. sd 0:0:0:0: [sda] Assuming drive cache: write through
     
530. sd 0:0:0:0: [sda] Assuming drive cache: write through
     
531. sda: sda1
     
532. sd 0:0:0:0: [sda] Assuming drive cache: write through
     
533. sd 0:0:0:0: [sda] Attached SCSI removable disk
     
534. FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
     
535. FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
     
536. usb 2-1: USB disconnect, address 2

复制代码

请不要胡乱输入以及粘贴、复制等方式灌水

请尊重作者、并共同维护网站的正常阅读，否则账户将会被限制发帖、回帖，并且积分可能会被清零，站内短信以及阅读权限等都会受到影响，谢谢。 具体限制方式：https://www.right.com.cn/forum/thread-8307840-1-1.html