|
楼主 |
发表于 2015-2-25 22:03
|
显示全部楼层
以下是正常加电的时候TTL反馈的信息:
UART1 output test ok
Uart init
mfid=000000c2 devid=00002249
Found 1 x 2M flash memory
---RealTek(RTL8186)at 2006.02.16-18:46+0800 version 1.4 [32bit](180MHz)
no sys signature at 00010000!
Jump to image start=0x80300000...
early printk enabled
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock1 console=0 single
Calibrating delay loop... 179.40 BogoMIPS
Memory: 14332k/16384k available (1477k kernel code, 2052k reserved, 140k data, 48k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
check_wait... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
state->flags=00000000
Realtek GPIO Driver for Flash Reload Default
block: 64 slots per queue, batch=16
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
CSLIP: code copyright 1989 Regents of the University of California.
PPP generic driver version 2.4.1
MPPE/MPPC encryption/compression module registered
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Found 1 x 2M Byte MXIC MX29LV160CB at 0xbe000000
Creating 2 MTD partitions on "DiskOnChip Millennium":
0x00000000-0x00100000 : "boot+cfg+linux"
0x00100000-0x00200000 : "root fs"
RTL8185 driver version 1.11 (2006-07-18)
rtl8186_init: Loading new ethernet driver!!
8186NIC Ethernet driver v0.0.4 (Sep 23, 2005)
eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4
eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5
fast_nat v1.3b-abc
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
ip_conntrack version 2.1 (128 buckets, 1024 max) - 312 bytes per conntrack
PPTP netfilter connection tracking: registered
PPTP netfilter NAT helper: registered
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 48k freed
mount /proc file system ok!
mount /var file system ok!
serial console detected. Disabling virtual terminals.
init started: BusyBox v1.00-pre8 (2006.08.10-06:16+0000) multi-call binary
BusyBox v1.00-pre8 (2006.08.10-06:16+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
36
37
mac_bit = 27
killall: l2tpd: no process killed
killall: l2tp.sh: no process killed
killall: pppd: no process killed
killall: pptp: no process killed
killall: telnetd: no process killed
killall: pptp.sh: no process killed
killall: pppoe.sh: no process killed
killall: bpalogin: no process killed
Initialize wlan0 interface
setup for WiFi test...
wifi_specific=0
Setup LNA ...
disable LNA
Setup BRIDGE interface
killall: syslogd: no process killed
killall: klogd: no process killed
SIOCGIFFLAGS: No such device
bridge br0 doesn't exist; can't delete it
Setup bridge...
device eth0 entered promiscuous mode
eth0:phy is 8305
SIOCDELRT: No such process
device eth1 entered promiscuous mode
eth1:phy is 8305
SIOCDELRT: No such process
device wlan0 entered promiscuous mode
SIOCDELRT: No such process
br0: port 3(wlan0) entering listening state
br0: port 2(eth1) entering listening state
br0: port 3(wlan0) entering learning state
br0: port 3(wlan0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering listening state
br0: port 2(eth1) entering learning state
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
SIOCDELRT: No such process
SIOCDELRT: No such process
SIOCDELRT: No such process
autoconf: not found
Setup Firewall
Auto-Discovery (ver 1.01)
killall: reload.sh: no process killed
killall: dnrd.sh: no process killed
774
# process DNRD disappear, restart this service!!
cat: /etc/resolv.conf: No such file or directory
restart DNS Relay Daemon
process DNRD disappear, restart this service!!
cat: /etc/resolv.conf: No such file or directory
restart DNS Relay Daemon
process DNRD disappear, restart this service!!
cat: /etc/resolv.conf: No such file or directory
restart DNS Relay Daemon
process DNRD disappear, restart this service!!
cat: /etc/resolv.conf: No such file or directory
restart DNS Relay Daemon
process DNRD disappear, restart this service!!
cat: /etc/resolv.conf: No such file or directory
restart DNS Relay Daemon
process DNRD disappear, restart this service!!
cat: /etc/resolv.conf: No such file or directory
restart DNS Relay Daemon
将在以上三行无限循环,请老师们予以帮助,谢谢! |
|