请求大哥们帮在忙 MOTO850G刷DD-WRT坏了

aaaaasss

从原厂6.14刷到 DD-WRT MINI的时候忘记复位了,直接在线刷的.(论坛上说从6.14刷DD-WRT一定要复位后再刷)
现在的情况是路由反复重启,连TTL线清NVRAM 刷原厂或其它固件,都是反复重启
请问有什么解决办法吗     QQ:  859655733 谢谢
下面是启动信息 :


CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Jul 29 16:18:25 CST 2004 (xavier@cvs.gemtek.com.tw)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena.
Initializing Devices.
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.50.21.0
CPU type 0x29007: 200MHz
Total memory: 0x2000000 bytes (32MB)

Total memory used by CFE:  0x8032C2C0 - 0x804317C0 (1070336)
Initialized Data:          0x8032C2C0 - 0x8032E410 (8528)
BSS Area:                  0x8032E410 - 0x8032F7C0 (5040)
Local Heap:                0x8032F7C0 - 0x8042F7C0 (1048576)
Stack Area:                0x8042F7C0 - 0x804317C0 (8192)
Text (code) segment:       0x80300000 - 0x80309870 (39024)
Boot area (physical):      0x00432000 - 0x00472000
Relocation Factor:         I:00000000 - D:00000000

Checking MAC address...
Wrote new MAC address to NVRAM_backup.
wl_hwaddr error. Skip GPLUS check.
Device eth0:  hwaddr 00-0C-10-21-32-02, ipaddr 192.168.10.1, mask 255.255.255.0
        gateway not set, nameserver not set

    *CFE for Motorola WR850G v5.00 [AFTERBURNER][FEM1], Release date: Jul. 29, 2004

Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: ............ 1552384 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
We got BCM4712 board...
Broadcom 3.51.21.0 version.
===== Set default value =====
Now set [os_ram_addr] to [80001000]
Now set [boardrev] to [0x10]
Now set [watchdog] to [0]
Now set [boot_wait] to [off]
Now set [et0mdcport] to [0]
Now set [pmon_ver] to [CFE 3.51.21.0]
Now set [vlan0ports] to [0 1 2 3 5*]
Now set [os_flash_addr] to [bfc40000]
Now set [sromrev] to [2]
Now set [boardtype] to [0x0101]
Now set [gpio2] to [adm_eecs]
Now set [gpio3] to [adm_eesk]
Now set [gpio4] to [adm_eedi]
Now set [gpio5] to [adm_rc]
Now set [wl0id] to [0x4320]
Now set [ag0] to [255]
Now set [wl0gpio0] to [0]
Now set [wl0gpio1] to [0]
Now set [wl0gpio2] to [0]
Now set [wl0gpio3] to [0]
Now set [wl0gpio4] to [0]
Now set [wl0gpio5] to [0]
Now set [boardflags2] to [0]
Now set [pa0itssit] to [62]
Now set [cctl] to [0]
Now set [pa0maxpwr] to [60]
Now set [clkfreq] to [200]
Now set [aa0] to [3]
Now set [vlan1hwname] to [et0]
Now set [vlan1ports] to [4 5]
Now set [scratch] to [a0180000]
Now set [ccode] to [0]
Now set [boardflags] to [0x0188]
Now set [sdram_init] to [0x0]
Now set [sdram_config] to [0x0032]
Now set [sdram_refresh] to [0x0000]
Now set [sdram_ncdl] to [0x21]
Now set [et0phyaddr] to [30]
Now set [pa0b0] to [0x119a]
Now set [pa0b1] to [0xfb93]
Now set [pa0b2] to [0xfea5]
Now set [vlan0hwname] to [et0]
Now set [dl_ram_addr] to [a0001000]
Now set [boardnum] to [44]
Now set [lan_ifname] to [br0]
Now set [lan_ifnames] to [vlan0 eth1 wds0.2 wds0.3 wds0.4 wds0.5]
Now set [wan_ifname] to [vlan1]
Now set [wan_ifnames] to [vlan1]
===================================
wlconf: vlan0 failed (-1)
wds0.2: No such device
wlconf: wds0.2 failed (-1)
interface wds0.2 does not exist!
wds0.3: No such device
wlconf: wds0.3 failed (-1)
interface wds0.3 does not exist!
wds0.4: No such device
wlconf: wds0.4 failed (-1)
interface wds0.4 does not exist!
wds0.5: No such device
wlconf: wds0.5 failed (-1)
interface wds0.5 does not exist!
NVRAM: WAN_linkstate does not exist!!
Is_WAN_Cable_Connected ... WAN side cable is connected ... Ok

aaaaasss

哪位高手帮帮忙啊,,,感激不尽

ZJeff

重写cfe 嘛

aaaaasss

原帖由 ZJeff 于 2009-2-28 15:41 发表
重写cfe 嘛

我也想做条JTAG线，但笔记本没有并口。 用TTL线能重写CFE吗？

hyppt

别乱写cfe
你试过tftp回复了么