|
|
本帖最后由 sd_smallbird 于 2017-11-22 09:41 编辑
另外发现，按不按reset启动都一样，都能打开mini cfe，但上传原机备份的CFE或者下载的CFE都说无效。也不知道它这个CFE mini server到底干啥用，怎么才能刷进去
Decompressing...done
Found ST compatible serial flash with 128 64KB blocks; total size 8MB
CFE version 9.10.178.27 (r584393) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Thu Apr 6 23:02:30 EDT 2017 (root@linux-tdxn)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 533 MHz
Info: DDR frequency set from clkfreq=900,*533*
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.27 (r584393)
CPU type 0x0: 900MHz
Tot mem: 131072 KBytes
CFE mem: 0x00F00000 - 0x017A358C (9057676)
Data: 0x00F6B934 - 0x00F6BF6C (1592)
BSS: 0x00F6BF78 - 0x00FA158C (218644)
Heap: 0x00FA158C - 0x017A158C (8388608)
Stack: 0x017A158C - 0x017A358C (8192)
Text: 0x00F00000 - 0x00F5F86C (391276)
Boot: 0x017A4000 - 0x017E4000
Reloc: I:00000000 - D:00000000
Mac:d8-32-14-XX-XX-XX
Device eth0: hwaddr D8-32-14-XX-XX-XX, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
upgrade wait time is 3s
**upgrade_wait over!
Loader:raw Filesys:raw Dev:flash0.os File: Options null)
Loading: .... 4133088 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
[ 0.780000] console [ttyS0] enabled, bootconsole disabled
[ 0.800000] brd: module loaded
[ 0.800000] loop: module loaded
[ 0.810000] pflash: found no supported devices
[ 0.810000] bcmsflash: squash filesystem found at block 28
[ 0.820000] Creating 7 MTD partitions on "bcmsflash":
[ 0.820000] 0x000000000000-0x000000800000 : "All"
[ 0.830000] 0x000000000000-0x000000040000 : "Bootloader"
[ 0.830000] 0x000000040000-0x0000007d0000 : "KernelFS"
[ 0.840000] 0x0000001ceb10-0x0000007d0000 : "rootfs"
[ 0.840000] 0x0000007d0000-0x0000007e0000 : "CFM_BACKUP"
[ 0.850000] 0x0000007e0000-0x0000007f0000 : "CFM"
[ 0.850000] 0x0000007f0000-0x000000800000 : "nvram"
[ 0.860000] nflash: found no supported devices
[ 0.860000] PPP generic driver version 2.4.2
[ 0.870000] PPP Deflate Compression module registered
[ 0.870000] PPP BSD Compression module registered
[ 0.880000] PPP MPPE Compression module registered
[ 0.880000] NET: Registered protocol family 24
[ 0.880000] Initializing USB Mass Storage driver...
[ 0.890000] usbcore: registered new interface driver usb-storage
[ 0.890000] USB Mass Storage support registered.
[ 0.900000] u32 classifier
[ 0.900000] Actions configured
[ 0.900000] Netfilter messages via NETLINK v0.30.
[ 0.910000] nf_conntrack version 0.5.0 (1962 buckets, 7848 max)
[ 0.910000] [BM CORE ] INFO: online ip data hash table created, size = 1 99
[ 0.920000] [BM CORE ] INFO: online_ip proc file created
[ 0.920000] ctnetlink v0.93: registering with nfnetlink.
[ 0.930000] create /proc/behavior/emailbcc SUCCESSFULLY.
[ 0.930000] netfilter smtp init successfully
[ 0.940000] xt_time: kernel timezone is -0000
[ 0.940000] Kernel:Init flow dev success.
[ 0.940000] IPv4 over IPv4 tunneling driver
[ 0.950000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 0.950000] TCP cubic registered
[ 0.950000] NET: Registered protocol family 17
[ 0.960000] L2TP core driver, V2.0
[ 0.960000] PPPoL2TP kernel driver, V2.0
[ 0.960000] L2TP IP encapsulation support (L2TPv3)
[ 0.970000] L2TP netlink interface
[ 0.970000] L2TP ethernet pseudowire support (L2TPv3)
[ 0.970000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.980000] All bugs added by David S. Miller <davem@redhat.com>
[ 1.030000] Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
[ 1.040000] brcmnand: found no supported devices
[ 1.040000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.050000] devtmpfs: mounted
[ 1.050000] Freeing init memory: 192K
[ 1.060000] Failed to execute /sbin/preinit. Attempting defaults...
mkdir: can't create directory '/var/run': File exists
[ 2.990000] [BM CORE ] INFO: bm_init success
[ 3.010000] bm_debug_init_proc success!
[ 3.010000] [U2K MODULE ] INFO: bm_u2k_info_init success
[ 3.080000] [MAC FILTER ] INFO: bm_mac_filter init success
[ 3.200000] [PRIVILEGE IP] INFO: privilege ip init success
[ 3.290000] qos qos_init 1627: qos module init success
[ 3.350000] OS TYPE INIT FINISHED
[ 3.350000] [URL FILTER ] INFO: url filter init success
[ 3.500000] fastnatconf fastnat_conf_init 611: fastnat conf module init succe ss
[ 3.520000] js: module license 'unspecified' taints kernel.
[ 3.530000] Disabling lock debugging due to kernel taint
[ 3.540000] js module ---2.0
[ 3.540000] init_module(1987)$string$
[ 3.560000] init_module(1989)$string$
[ 3.560000] creat nlsock ok!js=<script src="&g=/s&c=/s" defer></script> js st rlen =60
[ 3.800000] udevd (375): /proc/375/oom_adj is deprecated, please use /proc/37 5/oom_score_adj instead.
init_core_dump 1816: rlim_cur = 0, rlim_max = -1
init_core_dump 1825: open core dump success
init_core_dump 1834: rlim_cur = 5242880, rlim_max = 5242880
func:InitCfm begin load_mib....
flash_read:ret = 65536
crc = 3851ec, newcrc = 3851ec
######## STARTING PROGRAM #########
flash_read:ret = 65536
crc = 32549502, newcrc = 32549502
flash_read:ret = 65536
crc = 3851ec, newcrc = 3851ec
spawn-fcgi: child spawned successfully: PID: 388
Give root password for system maintenance
(or type Control-D for normal startup):flash_to_file pen Policy failed.
going to rewrite flash...
open /etc/policy_bak.cfg failed.
rewrite flash ok...
failure to open policy source: /etc/policy.cfg
left wan[0]:0
left lan[0]:1
left lan[1]:2
left lan[2]:3
left lan[3]:4
vlan_array[0]: value 1 index_num 1 name eth1 cpu_port 5index[0] 0 index[1] 0 index[2] 0 index[3] 0 index[4] 0
vlan_array[1]: value 0 index_num 4 name eth0 cpu_port 8index[0] 1 index[1] 2 index[2] 3 index[3] 4 index[4] 0
vlan_array[2]: value -2 index_num 0 name cpu_port 0index[0] 0 index[1] 0 ind ex[2] 0 index[3] 0 index[4] 0
vlan_array[3]: value -2 index_num 0 name cpu_port 0index[0] 0 index[1] 0 ind ex[2] 0 index[3] 0 index[4] 0
vlan_array[4]: value -2 index_num 0 name cpu_port 0index[0] 0 index[1] 0 ind ex[2] 0 index[3] 0 index[4] 0
nvram unset vlan1ports
nvram unset vlan2ports
nvram unset vlan3ports
nvram unset vlan4ports
nvram unset vlan5ports
nvram set vlan2ports="0 5*"
nvram set vlan1ports="1 2 3 4 8*"
#IPTV STB VLAN I[ 5.090000] zzj++:cmd:GPIO_IOC_REG_USB_LED
D mode is disable!#
main=>116:init server success.1..
No need to start gpio thread.
[ 5.180000] et_module_init: passivemode set to 0x0
[ 5.190000] et_module_init: txworkq set to 0x0
[ 5.190000] et_module_init: et_txq_thresh set to 0xce4
[ 5.200000] et_module_init: et_rxlazy_timeout set to 0x3e8
[ 5.200000] et_module_init: et_rxlazy_framecnt set to 0x20
[ 5.280000] stbport=4=wanport=0=
[ 5.290000] bcm_robo_enable_switch: EEE is disabled
[ 5.300000] eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10. 178.27 (r584393)
[ 5.320000] eth1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10. 178.27 (r584393)
insmod: can't read '/lib/modules/2.6.36.4brcmarm/kernel/drivers/net/proxyarp/pro xyarp.ko': No such file or directory
[ 7.080000] wl_module_init: passivemode set to 0x0
[ 7.080000] wl_module_init: txworkq set to 0x0
[ 7.110000] External imprecise Data abort at addr=0x1f4fc, fsr=0x1c06, pc=0x8 01f7a2c lr=0x801fdf6c ignored.
[ 7.120000] External imprecise Data abort at addr=0x1f4fc, fsr=0x1c06, pc=0x7 f0c71f8 lr=0x801fdf6c ignored.
[ 7.140000] eth2: Broadcom BCM43c8 802.11 Wireless Controller 9.10.178.27 (r5 84393 WLTEST)
[ 7.150000] PCI: Enabling device 0001:01:00.0 (0140 -> 0142)
[ 7.190000] eth3: Broadcom BCM43227 802.11 Wireless Controller 9.10.178.27 (r 584393 WLTEST)
insmod: can't read '/lib/modules/2.6.36.4brcmarm/kernel/drivers/usb/core/usbcore .ko': No such file or directory
[ 7.250000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.260000] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 7.260000] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus numbe r 1
[ 7.300000] ehci_hcd 0000:00:04.1: irq 36, io mem 0x18004000
[ 7.320000] ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
[ 7.320000] hub 1-0:1.0: USB hub found
[ 7.350000] hub 1-0:1.0: 2 ports detected
add
[ 7.460000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
add
[ 7.480000] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 7.480000] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus numbe r 2
[ 7.500000] ohci_hcd 0000:00:04.0: irq 36, io mem 0x1800d000
[ 7.570000] hub 2-0:1.0: USB hub found
add
[ 7.590000] hub 2-0:1.0: 2 ports detected
add
insmod: can't read '/lib/modules/2.6.36.4brcmarm/kernel/drivers/usb/storage/usb- storage.ko': No such file or directory
insmod: can't read '/lib/modules/2.6.36.4brcmarm/kernel/drivers/usb/class/usblp. ko': No such file or directory
insmod: can't read '/lib/modules/2.6.36.4brcmarm/kernel/drivers/usb/host/xhci-hc d.ko': No such file or directory
[ 7.710000] Hello,This is the USB LED handling Driver
[ 7.720000] >>si_gpioreserve : 0xffffffff
[ 7.720000] >>si_gpiocontrol : 0x0
[ 7.720000] >>si_gpioouten : 0x8546
[ 7.730000] >>si_gpioout : 0x8106
sh: can't create /proc/irq/163/smp_affinity: nonexistent directory
sh: can't create /proc/irq/169/smp_affinity: nonexistent directory
ifconfig: SIOCSIFHWADDR: No such device
ifconfig: SIOCGIFFLAGS: No such device
### set br0 mac [d8:32:14:b6:6b:e0]### [5]
##############add vlan devices [vconfig add eth1 2]
##############add vlan devices [vconfig add eth0 1]
[ 7.980000] device eth1 entered promiscuous mode
ifconfig: SIOCSIFHWADDR: No such device
[ 8.080000] device vlan1 entered promiscuous mode
[ 8.080000] device eth0 entered promiscuous mode
[ 8.100000] br0: topology change detected, propagating
[ 8.110000] br0: port 1(vlan1) entering forwarding state
[ 8.110000] br0: port 1(vlan1) entering forwarding state
[ 8.130000] IPv4 FIB: Using LC-trie version 0.409
Sat Jan 1 00:00:00 UTC 2000
Loading dnrd...
killall: dnrd: no process killed
[compatibility:is_compatible:80] The software is compatible!
_eval 98: child process create success
_eval 98: child process create success
_start_time_check 202: time_check register success, register_pid = 530
_eval 94: child process status is 0
_start_httpd 219: httpd register success, register_pid = 531
_eval 94: child process status is 0
_start_multiwan 283: _start_multiwan register success, register_pid = 532
_eval 94: child process status is 0
_start_ucloud_v2 357: ucloud_v2 register success, register_pid = 533
_eval 94: child process status is 0
_start_buisness_proc 383: buisness_proc register success, register_pid = 534
_eval 94: child process status is 0
_start_auto_discover 237: _start_auto_discover register success, register_pid = 535
business_proc
ucloud_v2
httpd
multiWAN
time_check
auto_discover
netctrl
Notice: caching turned off
[TIMER_CHECK >>time_check_reboot_info_printf(51)]: enable:1
[TIMER_CHECK >>time_check_reboot_info_printf(52)]: type:1
[TIMER_CHECK >>time_check_reboot_info_printf(57)]: wday_en:1;1;1;1 ;1;1;1
[TIMER_CHECK >>time_check_reboot_info_printf(58)]: start_time:03:0 0
[TIMER_CHECK >>time_check_reboot_info_printf(59)]: end_time:05:00
[TIMER_CHECK >>time_check_reboot_info_printf(60)]: max_speed:3
[TIMER_CHECK >>time_check_reboot_info_printf(61)]: check_speed=300 0
[TIMER_CHECK >>time_check_reboot_info_printf(62)]: wan_ifnames:vla n2
[TIMER_CHECK >>time_check_power_info_printf(50)]: enable:0
[TIMER_CHECK >>time_check_power_info_printf(51)]: type:1
[TIMER_CHECK >>time_check_power_info_printf(56)]: wday_en:1;1;1;1 ;1;1;1
[TIMER_CHECK >>time_check_power_info_printf(57)]: start_time:00:0 0
[TIMER_CHECK >>time_check_power_info_printf(58)]: end_time:07:00
[TIMER_CHECK >>time_check_power_info_printf(59)]: max_speed:3
[TIMER_CHECK >>time_check_power_info_printf(60)]: check_speed=300 0
wl2g_op:0 wl5g_op:0
fopen: No such file or directory
init_core_dump 1816: rlim_cur = 5242880, rlim_max = 5242880
init_core_dump 1825: open core dump success
init_core_dump 1834: rlim_cur = 5242880, rlim_max = 5242880
init_core_dump 1816: rlim_cur = 5242880, rlim_max = 5242880
init_core_dump 1825: open core dump success
init_core_dump 1834: rlim_cur = 5242880, rlim_max = 5242880
init_core_dump 1816: rlim_cur = 5242880, rlim_max = 5242880
init_core_dump 1825: open core dump success
init_core_dump 1834: rlim_cur = 5242880, rlim_max = 5242880
logserver.c check network 192.168.0.1 success
init_core_dump 1816: rlim_cur = 5242880, rlim_max = 5242880
init_core_dump 1825: open core dump success
init_core_dump 1834: rlim_cur = 5242880, rlim_max = 5242880
######## RECEIVING DATA #########
Yes:
****** WeLoveLinux******
|
|
/1 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2017-11-19 08:43
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
