|
NAND: ONFI device found
ID = 158061c8
Vendor = c8
Device = 61
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010010
MMC Device 0 not found
eth5 MAC Address from ART is not valid
write phy_id=1, reg(0x8074):0x0670
write phy_id=2, reg(0x8074):0x0670
write phy_id=3, reg(0x8074):0x0670
write phy_id=4, reg(0x8074):0x0670
bootwait is on, bootdelay=5
Hit any key to stop autoboot: 0
restore_defaults is set, enlarge xqup detect time
trigger button release!
boot from rootfs 1
miwifi: check crash in rmem !
ubi0: attaching mtd1
UBI init error 22
Erasing NAND...
Erasing at 0x6e0000 -- 100% complete.
Writing to NAND... OK
resetting ...
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAAA
S - OEM_IMAGE_VERSION_STRING=xiaoyang-gv
S - Boot Config, 0x000002e5
B - 203 - PBL, Start
B - 2738 - bootable_media_detect_entry, Start
B - 3447 - bootable_media_detect_success, Start
B - 3451 - elf_loader_entry, Start
B - 6120 - auth_hash_seg_entry, Start
B - 6363 - auth_hash_seg_exit, Start
B - 68624 - elf_segs_hash_verify_entry, Start
B - 131323 - PBL, End
B - 222192 - SBL1, Start
B - 304115 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 314211 - pm_device_init, Start
B - 500871 - PM_SET_VAL:Skip
D - 184525 - pm_device_init, Delta
B - 503158 - pm_driver_init, Start
D - 5368 - pm_driver_init, Delta
B - 509594 - clock_init, Start
D - 2104 - clock_init, Delta
B - 513650 - boot_flash_init, Start
D - 11895 - boot_flash_init, Delta
B - 529236 - boot_config_data_table_init, Start
D - 3202 - boot_config_data_table_init, Delta - (575 Bytes)
B - 536769 - Boot Setting : 0x00000600
B - 540704 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:16
B - 547627 - sbl1_ddr_set_params, Start
B - 551440 - CPR configuration: 0x300
B - 554825 - cpr_init, Start
B - 557723 - Rail:0 Mode: 5 Voltage: 808000
B - 562847 - CL CPR settled at 760000mV
B - 565683 - Rail:1 Mode: 5 Voltage: 880000
B - 569862 - Rail:1 Mode: 7 Voltage: 912000
D - 16470 - cpr_init, Delta
B - 576755 - Pre_DDR_clock_init, Start
B - 580781 - Pre_DDR_clock_init, End
B - 584166 - DDR Type : PCDDR3
B - 589778 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 594628 - DDR: Start of HAL DDR Boot Training
B - 599355 - DDR: End of HAL DDR Boot Training
B - 605028 - DDR: Checksum to be stored on flash is -1907442160
B - 615551 - Image Load, Start
D - 224053 - QSEE Image Loaded, Delta - (1373936 Bytes)
B - 839695 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 847381 - Image Load, Start
D - 10706 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B - 858178 - Image Load, Start
D - 25254 - RPM Image Loaded, Delta - (105964 Bytes)
B - 883524 - Image Load, Start
D - 96715 - APPSBL Image Loaded, Delta - (590292 Bytes)
B - 980361 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 986187 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 992561 - SBL1, End
D - 772687 - SBL1, Delta
S - Flash Throughput, 6747 KB/s (2096771 Bytes, 310726 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 800 MHz
U-Boot 2016.01 (Jul 08 2021 - 07:16:48 +0000), Build: jenkins-common_router_openwrt_ota_publish-1455
DRAM: smem ram ptable found: ver: 1 len: 4
512 MiB
NAND: ONFI device found
ID = 158061c8
Vendor = c8
Device = 61
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010010
MMC Device 0 not found
eth5 MAC Address from ART is not valid
write phy_id=1, reg(0x8074):0x0670
write phy_id=2, reg(0x8074):0x0670
write phy_id=3, reg(0x8074):0x0670
write phy_id=4, reg(0x8074):0x0670
bootwait is on, bootdelay=5
Hit any key to stop autoboot: 4
用的是FT232 插电一直跑按什么键也不停,有没有大佬懂得 感谢感谢
|
|