ax3600 ttl救砖 求个大佬指导一下

xiaowei1

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B -       201 - PBL, Start
B -      2735 - bootable_media_detect_entry, Start
B -      3443 - bootable_media_detect_success, Start
B -      3448 - elf_loader_entry, Start
B -      6115 - auth_hash_seg_entry, Start
B -      6359 - auth_hash_seg_exit, Start
B -     68574 - elf_segs_hash_verify_entry, Start
B -    131270 - PBL, End
B -    145607 - SBL1, Start
B -    198677 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    205295 - pm_device_init, Start
B -    328424 - PM_SET_VAL:Skip
D -    122457 - pm_device_init, Delta
B -    330681 - pm_driver_init, Start
D -      5337 - pm_driver_init, Delta
B -    337208 - clock_init, Start
D -      2165 - clock_init, Delta
B -    341173 - boot_flash_init, Start
D -     11773 - boot_flash_init, Delta
B -    356728 - boot_config_data_table_init, Start
D -      3202 - boot_config_data_table_init, Delta - (575 Bytes)
B -    364231 - Boot Setting :  0x00000600
B -    368165 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:16
B -    375089 - sbl1_ddr_set_params, Start
B -    378932 - CPR configuration: 0x300
B -    382409 - cpr_init, Start
B -    385184 - Rail:0 Mode: 5 Voltage: 816000
B -    390339 - CL CPR settled at 768000mV
B -    393175 - Rail:1 Mode: 5 Voltage: 880000
B -    397354 - Rail:1 Mode: 7 Voltage: 920000
D -     16470 - cpr_init, Delta
B -    404247 - Pre_DDR_clock_init, Start
B -    408273 - Pre_DDR_clock_init, End
B -    411658 - DDR Type : PCDDR3
B -    417270 - do ddr sanity test, Start
D -      1037 - do ddr sanity test, Delta
B -    422120 - DDR: Start of HAL DDR Boot Training
B -    426847 - DDR: End of HAL DDR Boot Training
B -    432520 - DDR: Checksum to be stored on flash is -1102448106
B -    442951 - Image Load, Start
D -    224114 - QSEE Image Loaded, Delta - (1373936 Bytes)
B -    667157 - Image Load, Start
D -        61 - SEC Image Loaded, Delta - (0 Bytes)
B -    674843 - Image Load, Start
D -     10705 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B -    685640 - Image Load, Start
D -     25254 - RPM Image Loaded, Delta - (105964 Bytes)
B -    710985 - Image Load, Start
D -     99796 - APPSBL Image Loaded, Delta - (611366 Bytes)
B -    810934 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -    816729 - USB D+ check, Start
D -        30 - USB D+ check, Delta
B -    823134 - SBL1, End
D -    679814 - SBL1, Delta
S - Flash Throughput, 6758 KB/s  (2117845 Bytes,  313381 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 800 MHz


U-Boot 2016.01 (Sep 11 2022 - 20:20:26 -0700)

DRAM:  smem ram ptable found: ver: 1 len: 4
512 MiB
NAND:  Could not find nand_gpio in dts, using defaults
ONFI device found
ID = 1590aac8
Vendor = c8
Device = aa
qpic_nand: changing oobsize to 64 from 128 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC:   sdhci: Node Not found, skipping initialization

*** Warning - bad CRC, using default environment

PCI Link Intialized
PCI1 is not defined in the device tree
In:    serial@78B3000
Out:   serial@78B3000
Err:   serial@78B3000
machid: 8010010
MMC Device 0 not found
eth5 MAC Address from ART is not valid

Net:   MAC0 addr:8c:53:c3:dc:bd:e8
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0
Hit any key to stop autoboot:  0

Net:   MAC0 addr:8c:53:c3:dc:bd:e8
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
, eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is         8c:53:c3:dc:bd:e8
Address in environment is  8c:53:c3:b4:80:68


这是ttl信息

xiaowei1

有没有大佬懂啊

倒影年华

看看能不能中断启动

jet慕情

正常的，中断一下。

jet慕情

https://www.right.com.cn/forum/thread-8253375-1-1.html

xiaowei1

现在插上网线只有10m