我的linksys wrt300n v2怎么不是intel CPU IPX 而显示Ralink的CPU，是不是假的？

testtest1

我的linksys wrt300n v2怎么不是intel CPU IPX 400MHZ，而是显示Ralink的CPU，是不是假的？
??
U-Boot 1.1.3 (Jan 14 2010 - 20:32:38)
Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 8377c000
Set info->start[0]=BF000000
flash_protect ON: from 0xBF000000 to 0xBF022F47
protect on 0
protect on 1
protect on 2
flash_protect ON: from 0xBF030000 to 0xBF03FFFF
protect on 3
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.2
--------------------------------------------
ASIC 3052_MP2 (Port5<->Phy)
DRAM COMPONENT: 256Mbits
DRAM BUS: 32BIT
Total memory: 64 MBytes
Date:Jan 14 2010  Time:20:32:38
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 384 MHZ ####
SDRAM bus set to 32 bit
SDRAM size =64 Mbytes
Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   9: Load Boot Loader code then write to Flash via TFTP.
0
   
3: System Boot system code via Flash.
eth_register  
Eth0 (10/100-M)
enetvar=ethaddr,Eth addr:00:0C:43:09:26:BB

eth_current->name = Eth0 (10/100-M)
verify is 1
## load addr bf050000 ...
print img header
   Magic:       [00000000]
   CRC:         [00000000]
   Image Name:   
   Created:      1970-01-01   0:00:00 UTC
System Control Status = 0x20440000
   Image Type:   Invalid CPU Invalid OS Invalid Image (uncompressed)
   Data Size:    0 Bytes =  0 kB
   Load Address: 00000000
   Entry Point:  00000000
Bad Magic Number , 00000000
## Booting image at bf050000 ...
sizeof image_header_t is 64
print img header
   Magic:       [27051956]
   CRC:         [3cbb42ca]
   Image Name:   Linux Kernel Image
   Created:      2013-06-08   2:11:55 UTC
System Control Status = 0x20440000
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4910089 Bytes =  4.7 MB
   Load Address: 80000000
   Entry Point:  80414000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80414000) ...
## Giving linux memsize in MB, 64
Starting kernel ...

LINUX started...
THIS IS ASIC
Linux version 2.6.21 (root@MaxWong) (gcc version 3.4.2) #650 Sat Jun 8 10:11:37 CST 2013
The CPU feqenuce set to 384 MHz
CPU revision is: 0001964c
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 90800060, status = 1100ff00
PID hash table entries: 256 (order: 8, 1024 bytes)
calculating r4koff... 00177000(1536000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 57020k/65536k available (3329k kernel code, 8452k reserved, 842k data, 3492k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
detected lzma initramfs
detected lzma initramfs
initramfs: LZMA lc=3,lp=0,pb=2,dictSize=1048576,origSize=14696960
LZMA initramfs by Ming-Ching Tiew <mctiew@yahoo.com>.................................................................................................................................................................................................................................================ 1 ==================
ralink flash device: 0x800000 at 0x1f000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 4 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Config"
0x00040000-0x00050000 : "Factory"
0x00050000-0x00800000 : "Kernel"
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
NTFS driver 2.1.28 [Flags: R/W].
fuse init (API version 7.8)
io scheduler noop registered (default)
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 1024K size 1024 blocksize
loop: loaded (max 8 devices)
rdm_major = 254
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v1.60  256 rx/tx descriptors allocated, mtu = 1500!
GDMA1_MAC_ADRH -- : 0x00008013
GDMA1_MAC_ADRL -- : 0x00b0c001
PROC INIT OK!
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
IMQ starting with 2 devices...
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.

=== pAd = c0019000, size = 512792 ===
<-- RTMPAllocAdapterBlock, Status=0
block2mtd: version $Revision: 1.1.1.1 $
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
dwc_otg: version 2.60a 22-NOV-2006
DWC_otg: Using DMA mode
dwc_otg lm0: DWC OTG Controller
dwc_otg lm0: new USB bus registered, assigned bus number 1
dwc_otg lm0: irq 18, io mem 0x00000000
DWC_otg: Init: Port Power? op_state=1
DWC_otg: Init: Power Port (0)
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
netem: version 1.2
u32 classifier
    Performance counters on
    OLD policer on
    input device check on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (25600 buckets, 204800 max)
ctnetlink v0.93: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
ipt_time loading
Loading ipp2p data module v0.99.17
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Cannot open root device "ram0" or unknown-block(1,0)
Please append a correct "root=" boot option
VFS: Cannot open root device "ram0" or unknown-block(1,0)
Please append a correct "root=" boot option
VFS: Cannot open root device "ram0" or unknown-block(1,0)
Please append a correct "root=" boot option
VFS: Cannot open root device "ram0" or unknown-block(1,0)
Please append a correct "root=" boot option
No filesystem could mount root, tried:  squashfs vfat ntfs fuseblk
Freeing unused kernel memory: 3492k freed
Hit enter to continue...switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg
phy_tx_ring = 0x00726000, tx_ring = 0xa0726000, size: 16 bytes
phy_rx_ring = 0x00727000, rx_ring = 0xa0727000, size: 16 bytes
write offset=48GDMA1_FWD_CFG = 10000
, value=1002
switch reg write offset=70, value=ffff506f
br0: No such device
RX DESC a072f000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
MCS Set = ff ff 00 00 01
Main bssid = 8c:28:09:10:04:c0
<==== rt28xx_init, Status=0
0x1300 = 00064380
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
eth2.1: Setting MAC address to  8c 28 09 10 04 c0.
device eth2 entered promiscuous mode
VLAN (eth2.1):  Setting underlying device (eth2) to promiscious mode.
device ra0 entered promiscuous mode
eth2.1: dev_set_promiscuity(master, 1)
device eth2.1 entered promiscuous mode
Algorithmics/MIPS FPU Emulator v1.5
br0: port 2(eth2.1) entering learning state
br0: port 1(ra0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth2.1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(ra0) entering forwarding state
SIOCSIFFLAGS: Cannot assign requested address
br0: port 1(ra0) entering disabled state
RX DESC a046b000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
MCS Set = ff ff 00 00 01
Main bssid = 8c:28:09:10:04:c0
<==== rt28xx_init, Status=0
0x1300 = 00064380
br0: port 1(ra0) entering learning state
br0: topology change detected, propagating
br0: port 1(ra0) entering forwarding state
killall: rt2860apd: no process killed
rt2860apd: No such file or directory
info, udhcp server (v0.9.8) started
snmpd: No such file or directory
pptpd: No such file or directory
time.windows.com: Unknown host
eth2.2: Setting MAC address to  8c 28 09 10 04 be.
info, udhcp client (v0.9.8) started
IDLE
Hit enter to continue...

Enter 'help' or '?' for a list of built-in commands.

cybplus

用雷凌的山寨300N早就不稀奇了，论坛里面已经有不少人多次提到，这种山寨机固件从一开始山寨TOMATO界面，现在已经开始山寨公版的LINKSYS固件了。就算是原版机在现在也已经不是什么好东西，山寨机卖得还不便宜，但是X宝的销量却惊人的高，真是搞不懂。

ls2025

我也买了一个但是信号确实是牛B

laoma348

山寨的啊