|
这个软件这次安装了8个小时了,不断的上网找,一直没找到错在哪儿。快没脾气了!
按照教程linux bt速度之王—— rtorrent DHT版本 For Oleg optware(7231-4P,WL-500g,mss可用 )
安装完毕后
运行了export HOME=/opt/root
运行l/opt/bin/rtorrent
出现
然后
没有运行export HOME=/opt/root
运行l/opt/bin/rtorrent
出现
退也退不出来
/opt/root目录这样
/opt/ect目录这样
为什么呢?
我的配置文件是这样的有什么问题吗?
# This is an example resource file for rTorrent. Copy to
# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
# uncomment the options you wish to enable.
# Minumum amount of peers to connect per torrent, if available.
min_peers = 20
# Minumum amount of peers to connect per torrent.
max_peers = 40
# Same as above but for seeding completed torrents (-1 = same as downloading)
#min_peers_seed = 10
#max_peers_seed = 20
# Maximum number of simultanious uploads per torrent.
max_uploads = 5
# Global download rate in KiB. "0" for unlimited.
download_rate = 80
# Global upload rate in KiB. "0" for unlimited.
upload_rate = 80
# Default directory to save downloaded files. Note it doesn't support
# space yet.
directory = /mnt/C/BT
# Watch a directory for new torrents, and stop those that have been deleted.
schedule = watch_directory,5,5,load_start=/mnt/C/BT/torrent/*.torrent
#schedule = untied_directory,5,5,stop_untied=
# Close torrents when diskspace is low.
#schedule = low_diskspace,5,60,close_low_diskspace=100M
# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a
# relative path?
session = /mnt/C/BT/torrent/session
# The ip address reported to the tracker.
#ip = rakshasa
# The ip address the listening socket and outgoing connections is
# bound to.
#bind = rakshasa
# Port range to use for listening.
port_range = 51777-51780
# Start opening ports at a random position within the port range.
#port_random = no
# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
#check_hash = no
# Set whetever the client should try to connect to UDP trackers.
use_udp_trackers = yes
# Alternative calls to bind and ip that should handle dynamic ip's.
#schedule = ip_tick,0,1800,ip=rakshasa
#schedule = bind_tick,0,1800,bind=rakshasa
#
# Do not modify the following parameters unless you know what you're doing.
#
# Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
#hash_read_ahead = 10
# Interval between attempts to check the hash, in milliseconds.
#hash_interval = 100
# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
#hash_max_tries = 10
# Max number of files to keep open simultaniously.
#max_open_files = 128
# Number of sockets to simultaneously keep open.
#max_open_sockets = <no default>
# Example of scheduling commands: Switch between two ip's every 5
# seconds.
#schedule = "ip_tick1,5,10,ip=torretta"
#schedule = "ip_tick2,10,10,ip=lampedusa"
# Remove a scheduled event.
#schedule_remove = "ip_tick1"
# Stop torrents when reaching upload ratio in percent,
# when also reaching total upload in bytes, or when
# reaching final upload ratio in percent.
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
#schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"
schedule = ratio,30,60,stop_on_ratio=200
# Encryption options, set to none (default) or any combination of the following:
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
#
# encryption = allow_incoming,enable_retry,prefer_plaintext
# Enable DHT support for trackerless torrents or when all trackers are down.
# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
# The default is "off". For DHT to work, a session directory must be defined.
#
# dht = auto
# UDP port to use for DHT.
#
# dht_port = 6881
# Enable peer exchange (for torrents not marked private)
#
# peer_exchange = yes
#
# Do not modify the following parameters unless you know what you're doing.
#
[ 本帖最后由 Fansly 于 2008-2-24 00:35 编辑 ] |
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有账号?立即注册
×
|