腾达FH1202 11AC双频路由拆解（有TTL）

lion2002

没有编程器，不敢换固件，
线路板版本：10017026 V1.0
FLASH:  8M  (25Q64BS1G)
RAM:    64 (W9751G6KB-25)
DC-DC: FR9886， FR9888
2.4G
3天线     2T3R ?
开关 ：  SKY13377
功放：    5641

5G
BCM43526   （这个是估出来的）
2天线
功放:  5633

lion2002

CFE version 6.37.14.9 (r409124) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Jul 11 13:55:55 CST 2013 (root@linux-svzy-cj)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.9 (r409124)
CPU type 0x19749: 500MHz
Tot mem: 65536 KBytes

CFE mem:    0x80E00000 - 0x80E9A950 (633168)
Data:       0x80E31570 - 0x80E336E0 (8560)
BSS:        0x80E336E0 - 0x80E34950 (4720)
Heap:       0x80E34950 - 0x80E98950 (409600)
Stack:      0x80E98950 - 0x80E9A950 (8192)
Text:       0x80E00000 - 0x80E31568 (202088)

Device eth0:  hwaddr C8-3A-35-2B-2B-2B, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: .... 4385244 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22 (root@linux-ger5) (gcc version 4.2.3) #68 PREEMPT Tue Dec 10 08:10:12 CST 2013
CPU revision is: 00019749
Found an ST compatible serial flash with 128 64KB blocks; total size 8MB
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 16256
Kernel command line: root=/dev/mtdblock3 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM5357 rev 2 at 500 MHz
Using 250.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60080k/65536k available (3387k kernel code, 5400k reserved, 672k data, 220k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
PCI: no core
PCI: no core
PCI: Fixing up bus 0
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
fuse init (API version 7.8)
io scheduler noop registered (default)
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
骵rial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
loop: module loaded
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.3
pflash: found no supported devices
sflash: squash filesystem with lzma found at block 27
Creating 7 MTD partitions on "sflash":
0x00000000-0x00800000 : "All"
0x00000000-0x00040000 : "Bootloader"
0x00040000-0x00790000 : "KernelFS"
0x001b52f4-0x00790000 : "rootfs"
0x00790000-0x007e0000 : "WebFS"
0x007e0000-0x007f0000 : "CFM"
0x007f0000-0x00800000 : "nvram"
nflash: found no supported devices
brcmnand: found no supported devices
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
create /proc/behavior/emailbcc SUCCESSFULLY.
netfilter smtp init successfully
Kernel:Init flow dev success.
IPv4 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 220k freed
init started: BusyBox v1.13.0 (2013-04-28 11:06:03 CST
starting pid 610, tty '': '/etc/init.d/rcS
Algorithmics/MIPS FPU Emulator v1.5
starting pid 630, tty '': '/bin/cfm_check
starting pid 631, tty '/dev/ttyS0': '/sbin/sulogin
Give root password for system maintenance
(or type Control-D for normal startup):pid = 630
cmds = echo 630 > /var/cfm_check


Yes:

      ****** WeLoveLinux ******

Welcome to ...
init server success.1..
ctf: module license 'Proprietary' taints kernel.
et_module_init: passivemode set to 0x1
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0x400
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.34 (r415984)
insmod: cannot insert '/lib/modules/2.6.22/kernel/drivers/net/proxyarp/proxyarp.ko': unknown symbol in module, or unknown parameter
insmod: cannot insert '/lib/modules/2.6.22/kernel/drivers/net/dpsta/dpsta.ko': unknown symbol in module, or unknown parameter
wl_module_init: passivemode set to 0x0
wl_module_init: txworkq set to 0x0
eth1: Broadcom BCM4347 802.11 Wireless Controller 6.37.14.34 (r415984 WLTEST)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
wombo_reset set to gpio 23
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: EHCI Fastpath: New EHCI driver starting
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Symbol usb_register_driver is being used by a non-GPL module, which will not be allowed in the future
Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details.
Symbol usb_deregister is being used by a non-GPL module, which will not be allowed in the future
Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details.
EHCI Fastpath: usb_dev 82c7e000
EHCI Fastpath: bus 82bac800
EHCI Fastpath: Hub 82c7e800
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the bypass device command in EHCI 82c7e000
EHCI Fastpath: usb_dev 82c7e000
EHCI Fastpath: bus 82bac800
EHCI Fastpath: Hub 82c7e800
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the bypass callback command in EHCI c046eb84
EHCI Fastpath: usb_dev 82c7e000
EHCI Fastpath: bus 82bac800
EHCI Fastpath: Hub 82c7e800
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the bypass fastpath pool command in EHCI 82822380
EHCI Fastpath: usb_dev 82c7e000
EHCI Fastpath: bus 82bac800
EHCI Fastpath: Hub 82c7e800
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the RH bypass command in EHCI for EP #0 0004
ehci_hcd 0000:00:04.1: EHCI Fastpath: release native dummy qtd and alloc new one
ehci_hcd 0000:00:04.1: EHCI Fastpath: EP 83e7bbf8 QH a338a100 dummy a2823000
EHCI Fastpath: usb_dev 82c7e000
EHCI Fastpath: bus 82bac800
EHCI Fastpath: Hub 82c7e800
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the RH bypass command in EHCI for EP #1 0012
ehci_hcd 0000:00:04.1: EHCI Fastpath: release native dummy qtd and alloc new one
ehci_hcd 0000:00:04.1: EHCI Fastpath: EP 83e7bba8 QH a338a180 dummy a2823060
EHCI Fastpath: EP in 18 EP in2 19 EP out 4
bcm_rpc_up: waiting to be connected
bcm_rpc_buf_recv_mgn_high: Recvd:3 Version: 0x6250e22
State: 3 Session:105
bcm_rpc_buf_recv_mgn_high: Reason: 0 Dongle Version: 0x6250e22
bcm_rpc_buf_recv_mgn_high: Connected!
eth2: Broadcom BCMaa06 802.11 Wireless Controller 6.37.14.34 (r415984 WLTEST)
usbcore: registered new interface driver dbus_usbdev
eth0.1: Setting MAC address to  c8 3a 35 31 5e e0.
VLAN (eth0.1):  Underlying device (eth0) has same MAC, not checking promiscious mode.
eth0.2: Setting MAC address to  c8 3a 35 31 5f e1.
device eth0 entered promiscuous mode
VLAN (eth0.2):  Setting underlying device (eth0) to promiscious mode.
br0: starting userspace STP failed, staring kernel STP
eth0.1: dev_set_promiscuity(master, 1)
device eth0.1 entered promiscuous mode
br0: port 1(eth0.1) entering listening state
br0: port 1(eth0.1) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0.1) entering forwarding state
br10: starting userspace STP failed, staring kernel STP
device eth1 entered promiscuous mode
device eth2 entered promiscuous mode
IPv4 FIB: Using LC-trie version 0.408
Sat Jan  1 00:00:00 UTC 2000
sh: can't create /proc/conn_max: nonexistent directory
sh: can't create /proc/sys/net/ipv4/udp_mem: nonexistent directory
sh: can't create /proc/sys/net/ipv4/udp_rmem_min: nonexistent directory
sh: can't create /proc/sys/net/ipv4/udp_wmem_min: nonexistent directory
sh: tc: not found
sh: tc: not found
sh: tc: not found
sh: tc: not found
sh: tc: not found
No need to start gpio thread.
sntp.c check network 192.168.0.1 success
cfm_check_pid  = 630
killall: dnrd-guest: no process killed


Yes:

      ****** WeLoveLinux ******

Welcome to ...
logserver.c check network 192.168.0.1 success
main.c check network 192.168.0.1 success
main.c check network 192.168.0.1 success

Stop Ftp Sev......
open /proc/tdproc/lanip failed
Init tQoS dev success.
mac_filter_init.....
ipmacbind_init.....
groupip_init.....
client_filter_init.....
start url_filter_init...................
sh: can't create /proc/br0_ip: nonexistent directory
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name

=====>MAX_WIFI_SSID_NUM[2]
WIFI Trace  [wireless_reset]  ...
WIFI INFO : [wlhandle_switch_button] High Power Product

Usage: bcmgpio set/get gpio_pin 1/0
comprLen[3308]

#####CRC[f4f81d50]
Erasing 64 Kbyte @ 0 -- 100 % complete.
commit crc [f4f81d50]
sh: ebtables: not found
WIFI INFO : [load_wlinfo_from_mib] wl interface : eth1
WIFI INFO : [load_wlinfo_from_mib] wl interface : wl0.1
WIFI INFO : Wl_ifname wl0.1 disabled,[load_wlinfo_from_mib] break off!

WIFI INFO : [load_wlinfo_from_mib] wl interface : eth2
WIFI INFO : [load_wlinfo_from_mib] wl interface : wl1.1
WIFI INFO : Wl_ifname wl1.1 disabled,[load_wlinfo_from_mib] break off!

WIFI INFO : [set_wireless_all] wl interface eth1
WIFI Trace  [set_wireless_basic]  ...
WIFI Trace  [set_wl24g_bgn]  ...
WIFI INFO : 24G 11b/g/n mixed .
WIFI Trace  [set_wireless_basic_vif]  ...
WIFI Trace  [set_wireless_advance]  ...
WIFI Trace  [set_wireless_filter]  ...
WIFI Trace  [set_wireless_filter]  ...
wlctl: wl driver adapter not found
wlctl: wl driver adapter not found
WIFI Trace  [set_wireless_security]  ...
WIFI INFO : WPA_PSK
WIFI Trace  [set_wireless_workmode]  ...
WIFI Trace  [set_wireless_ap]  ...
WIFI Trace  [set_wireless_wds]  ...
WIFI INFO : [set_wireless_all] wl interface eth2
WIFI Trace  [set_wireless_basic]  ...
WIFI Trace  [set_wl5g_an]  ...
WIFI INFO : 5G actual set channel to:153/80

WIFI Trace  [set_wireless_basic_vif]  ...
WIFI Trace  [set_wireless_advance]  ...
WIFI Trace  [set_wireless_filter]  ...
Restart [multiWAN]....
killall: multiWAN: no process killed
WIFI Trace  [set_wireless_filter]  ...
wlctl: wl driver adapter not found
wlctl: wl driver adapter not found
WIFI Trace  [set_wireless_security]  ...
WIFI Trace  [set_wireless_workmode]  ...
WIFI Trace  [set_wireless_ap]  ...
WIFI Trace  [set_wireless_wds]  ...
WIFI Trace  [set_lan_ifname]  ...
[multiWAN]main.c check network 192.168.0.1 success
WIFI Trace  [wireless_restart]  ...
WIFI Trace  [stop_wl_services]  ...
Restart [dhcps]....
killall: dhcps: no process killed
WIFI Trace  [wireless_stop]  ...
device eth1 left promiscuous mode
br0: port 2(eth1) entering disabled state
device eth2 left promiscuous mode
br0: port 3(eth2) entering disabled state
Invalid instance identifier br0

Restart [miniupnpd]....
killall: miniupnpd: no process killed
Invalid instance identifier br0

Command failed
Invalid instance identifier br0

miniupnpd.c,865,ver=1.0,osname=Wireless Router,osver=1.0,osurl=http://192.168.0.1,manuft=Tenda,descri=Wireless Router
interface wl0.1 does not exist!
interface wl1.1 does not exist!
WIFI Trace  [wireless_start]  ...
WIFI INFO : wl_probe vlan1 failed.

vlan1: WLC_GET_VAR(cap): No such device
interface vlan1 does not exist!
ifconfig eth1 up
eth1: cmd=231: Invalid argument
eth1: WLC_SET_VAR(bsscfg:radio_pwrsave_enable): Operation not permitted
eth1: WLC_SET_VAR(chanspec): Invalid argument
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(rx_amsdu_in_ampdu): Operation not supported
eth1: WLC_SET_VAR(bg_rate): Operation not supported
eth1: WLC_SET_VAR(a_rate): Operation not supported
eth1: WLC_SET_VAR(bg_rate): Operation not supported
eth1: WLC_SET_VAR(a_rate): Operation not supported
eth1: WLC_SET_VAR(bg_mrate): Operation not supported
eth1: WLC_SET_VAR(a_mrate): Operation not supported
eth1: WLC_SET_VAR(bg_mrate): Operation not supported
eth1: WLC_SET_VAR(a_mrate): Operation not supported
eth1: WLC_SET_VAR(avg_dma_xfer_rate): Operation not supported
killall: dnrd: no process killed
device eth1 entered promiscuous mode
br0: port 2(eth1) entering listening state
br0: port 2(eth1) entering learning state
killall: dnrd-guest: no process killed
multwan init ok.br0: topology change detected, propagating

br0: port 2(eth1) entering forwarding state
ifconfig eth2 up
Notice: caching turned off
eth2: cmd=231: Invalid argument
eth2: WLC_SET_VAR(bsscfg:radio_pwrsave_enable): Operation not permitted
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(bg_rate): Operation not supported
eth2: WLC_SET_VAR(a_rate): Operation not supported
eth2: WLC_SET_VAR(bg_rate): Operation not supported
eth2: WLC_SET_VAR(a_rate): Operation not supported
eth2: WLC_SET_VAR(bg_mrate): Operation not supported
eth2: WLC_SET_VAR(a_mrate): Operation not supported
eth2: WLC_SET_VAR(bg_mrate): Operation not supported
eth2: WLC_SET_VAR(a_mrate): Operation not supported
eth2: WLC_SET_VAR(avg_dma_xfer_rate): Operation not supported
eth2: WLC_SET_VAR(nar): Operation not supported
device eth2 entered promiscuous modet supported

eth2: WLC_SET_Vbr0: port 3(eth2) entering listening state
AR(ebos_enable):br0: port 3(eth2) entering learning state
Operation not supported
eth2: cmd=64: Operatiobr0: topology change detected, propagating
br0: port 3(eth2) entering forwarding state

eth2: WLC_SET_VAR(bsscfg:pspretend_retry_limit): Operation not supported
eth2: WLC_SET_VAR(pspretend_retry_limit): Operation not supported
eth2: WLC_SET_VAR(pspretend_threshold): Operation not supported
eth2: WLC_SET_VAR(wmf_ucast_igmp_query): Operation not supported
eth2: WLC_SET_VAR(wmf_ucast_upnp): Operation not supported
eth2: WLC_SET_VAR(wmf_igmpq_filter): Operation not supported
WIFI INFO : GetValue lan.macaddr() failed.

WIFI Trace  [start_wl_services]  ...
[start_wl_services] eapd
[start_wl_services] nas
[start_wl_services] ses -f
[start_wl_services] ses_cl -f
[start_wl_services] wps_monitor
[start_wl_services] acsd
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
iptables: No chain/target/match by that name
iptables v1.4.0: Couldn't find target `Xrate'

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name
acsd: scan in progress ...
iptables: No chain/target/match by that name
iptables v1.4.0: Couldn't find target `Xuprate'

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables v1.4.0: Couldn't find target `Xmark'

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0x1803
[start_wl_services] comad
WIFI Trace  [set_wl_pwr_percent]  ...
wlctl: Unsupported
kdz===>lan_ip = 192.168.0.1
open /dev/gsbmac failed.
killall: arpbrocast: no process killed
open /dev/fence failed.
open /dev/fence failed.
open /dev/fence failed.
ip: RTNETLINK answers: No such file or directory
set port 3 to AUTO
WIFI Trace  [wireless_restart]  ...
WIFI Trace  [stop_wl_services]  ...
WIFI Trace  [wireless_stop]  ...
br0: port 2(eth1) entering disabled state
device eth1 left promiscuous mode
br0: port 2(eth1) entering disabled state
br0: port 3(eth2) entering disabled state
device eth2 left promiscuous mode
br0: port 3(eth2) entering disabled state
Invalid instance identifier br0

Invalid instance identifier br0

Command failed
Invalid instance identifier br0

interface wl0.1 does not exist!
interface wl1.1 does not exist!
WIFI Trace  [wireless_start]  ...
WIFI INFO : wl_probe vlan1 failed.

vlan1: WLC_GET_VAR(cap): No such device
interface vlan1 does not exist!
ifconfig eth1 up
eth1: cmd=231: Invalid argument
eth1: WLC_SET_VAR(bsscfg:radio_pwrsave_enable): Operation not permitted
eth1: WLC_SET_VAR(bsscfg:radio_pwrsave_level): Invalid argument
eth1: WLC_SET_VAR(chanspec): Invalid argument
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation device eth1 entered promiscuous mode
not supported
ebr0: port 2(eth1) entering listening state
th1: WLC_SET_VARbr0: port 2(eth1) entering learning state
(ampdu_rr_retry_br0: topology change detected, propagating
limit_tid): Operbr0: port 2(eth1) entering forwarding state
ation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth1: WLC_SET_VAR(rx_amsdu_in_ampdu): Operation not supported
eth1: WLC_SET_VAR(bg_rate): Operation not supported
eth1: WLC_SET_VAR(a_rate): Operation not supported
eth1: WLC_SET_VAR(bg_rate): Operation not supported
eth1: WLC_SET_VAR(a_rate): Operation not supported
eth1: WLC_SET_VAR(bg_mrate): Operation not supported
eth1: WLC_SET_VAR(a_mrate): Operation not supported
eth1: WLC_SET_VAR(bg_mrate): Operation not supported
eth1: WLC_SET_VAR(a_mrate): Operation not supported
eth1: WLC_SET_VAR(avg_dma_xfer_rate): Operation not supported
ifconfig eth2 up
eth2: cmd=231: Invalid argument
eth2: WLC_SET_VAR(bsscfg:radio_pwrsave_enable): Operation not permitted
eth2: WLC_SET_VAR(bsscfg:radio_pwrsave_level): Invalid argument
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(bg_rate): Operation not supported
eth2: WLC_SET_VAR(a_rate): Operation not supported
eth2: WLC_SET_VAR(bg_rate): Operation not supported
eth2: WLC_SET_VAR(a_rate): Operation not supported
eth2: WLC_SET_VAR(bg_mrate): Operation not supported
eth2: WLC_SET_VAR(a_mrate): Operation not supported
eth2: WLC_SET_VAR(bg_mrate): Operation not supported
eth2: WLC_SET_VAR(a_mrate): Operation not supported
eth2: WLC_SET_VAR(avg_dma_xfer_rate): Operation not supported
eth2: WLC_SET_VAR(nar): Operation not supported
eth2: WLC_SET_VAR(taf): Operation not supported
eth2: WLC_SET_VAR(ebos_enable): Operation not supportdevice eth2 entered promiscuous mode
ed
eth2: cmd=64br0: port 3(eth2) entering listening state
: Operation not supported
eth2: WLC_SET_VAR(bssbr0: port 3(eth2) entering learning state
cfg:pspretend_retry_limit): Operation not supported
eth2: WLC_Sbr0: topology change detected, propagating
ET_VAR(pspretendbr0: port 3(eth2) entering forwarding state
_retry_limit): Operation not supported
eth2: WLC_SET_VAR(pspretend_threshold): Operation not supported
eth2: WLC_SET_VAR(wmf_ucast_igmp_query): Operation not supported
eth2: WLC_SET_VAR(wmf_ucast_upnp): Operation not supported
eth2: WLC_SET_VAR(wmf_igmpq_filter): Operation not supported
WIFI INFO : GetValue lan.macaddr() failed.

WIFI Trace  [start_wl_services]  ...
[start_wl_services] eapd
[start_wl_services] nas
[start_wl_services] ses -f
[start_wl_services] ses_cl -f
[start_wl_services] wps_monitor
[start_wl_services] acsd
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
eth1: cmd=51: Invalid argument
ACSD >>acs_get_scan(817): err from WLC_SCAN_RESULTS: -1
ACSD >>acs_start(1625): request data failed
ret code: -1
ACSD >>acs_init_run(2678): acs_start failed for ifname: eth1
[start_wl_services] comad
httpd listen ip = 192.168.0.1 port = 80
webs: Listening for HTTP requests at address 192.168.0.1
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0x1803

atheros

谢谢分享。{:soso_e100:}

yech163

cpu主频才500 难道是哪个47186??

pppeng-101

CPU：bcm5358 Bo

pppeng-101

CPU图片来了

LZ的是FH1202，我这个是F1202

popi989

求个原版cfe

凹凸凹凸凹凸

我串口调试竟然需要密码，这款路由器的默认密码root密码是什么？

tom4733

lion2002 发表于 2014-6-23 22:11
CFE version 6.37.14.9 (r409124) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Jul  ...

这么长，怎么操作啊？

HFTDGH

这应该是抓的日志这么长