求救啊， mw310r TTL刷机.

guolicheng

手上有台 水星310r。刷好的 华硕N14了。想刷Op. 怎么也刷不回了， 想刷入 uboot,求指点 哪里是ttl 线插口啊、如何接线呢？  com口插头倒是有好几个，是不是把线接好 就可以当TTL 用呢？

guolicheng

有指点下得吗？ {:soso_e101:}  圈里的那个是TTL接口吗？ 我咋焊线序呢？

jiangshunmin

guolicheng 发表于 2014-10-6 17:36
有指点下得吗？   圈里的那个是TTL接口吗？ 我咋焊线序呢？

万用表测试，与负极电阻最小的是GND，然后通电与GND电压最高的是VCC， 电压最高的这个就不要用了。剩下两根接ttl测试，如果没有正确的显示信息，就反过来，就行了。。。

housecall

最右边单独的那个是Vcc，靠近Vcc那个是GND，接下来就是RXTX了

hanhg

能刷N14的，应该是不死uboot，按着reset键开机，就可以进入web挽救模式刷支持的固件！

modi5156

hanhg 发表于 2014-10-6 21:02
能刷N14的，应该是不死uboot，按着reset键开机，就可以进入web挽救模式刷支持的固件！

大神！任何刷了不死UBOOT都能这样自救的吗

hanhg

modi5156 发表于 2014-10-7 00:47
大神！任何刷了不死UBOOT都能这样自救的吗

是的，不然要不死uboot做什么呢？

guolicheng

请问： 帮我看看问题出在哪里？


udhcpc_wan:: leasefail
udhcpc_wan:: leasefail
Reset Count 11.Current Date 0-14-14.
udhcpc_wan:: leasefail
udhcpc_wan:: leasefail
[1 init:init_main +931] main loop signal/state=14
udhcpc_wan:: leasefail
Reset Count 12.Current Date 0-16-16.
udhcpc_wan:: leasefail


U-Boot 1.1.3 (Oct 26 2013 - 18:10:05)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb0000
enable ephy clock...done. rf reg 29 = 5
SSC enabled. swing=5000, upperbound=0
spi_wait_nsec: 3e
spi device id: ef 40 18 0 0 (40180000)
find flash: W25Q128FV
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Oct 26 2013  Time:18:10:05
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 386 MHZ ####
estimate memory size =64 Mbytes
ASUS RT-N14U gpio init : wps / reset pin
ppe reset

Please choose the operation:
   0: Load system code then write to Flash via Serial.
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   5: Load Boot Loader code to SDRAM via Serial.
   7: Load Boot Loader code then write to Flash via Serial.
   8: Load Boot Loader code to SDRAM via TFTP.
   9: Load Boot Loader code then write to Flash via TFTP.
0
   
3: System Boot system code via Flash.
raspi_read: from:4018a len:4

Bootloader version: 1.0.0.1
raspi_read: from:40004 len:6
MAC Address: 00:11:11:11:11:11
raspi_read: from:40028 len:6

before LEDON:
data:fc7f86
Do bootm
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    12486368 Bytes = 11.9 MB
   Load Address: 80000000
   Entry Point:  8000c150
raspi_read: from:50040 len:be86e0
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c150) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

THIS IS ASIC
Linux version 2.6.36 (root@asus) (gcc version 4.2.4) #214 Wed Jan 15 19:15:08 CST 2014

The CPU feqenuce set to 386 MHz
ramsize = 64 MBytes
rambase not set, set to default (0x00000000)
PCIE: bypass PCIe DLL.
PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
disable all power about PCIe
PCIE: PLL power down for MT7620N
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squashfs noinitrd
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0002fff7
Readback ErrCtl register=0002fff7
Memory: 61508k/65536k available (2643k kernel code, 4028k reserved, 544k data, 172k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 257.02 BogoMIPS (lpj=514048)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Load Ralink Timer0 Module
Load Ralink Timer1 Module
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 120
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
deice id : ef 40 18 0 0 (40180000)
W25Q128BV(ef 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
partion 3: ffffffff f30000
partion 4: 16a300 e15d00
#add mtd partition#
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "nvram"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000f80000 : "linux"
0x00000016a300-0x000000f80000 : "rootfs"
0x000000f80000-0x000001000000 : "jffs2"
0x000000000000-0x000001000000 : "ALL"
rdm_major = 253
Allocate 4096 entries coherent memory for hw_nat. (327680 bytes)
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x432880a8
Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x4328804d
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
        Hooking IMQ after NAT on PREROUTING.
        Hooking IMQ before NAT on POSTROUTING.
u32 classifier
nf_conntrack version 0.5.0 (961 buckets, 3844 max)
matchsize=264
xt_time: kernel timezone is -0000
GRE over IPv4 demultiplexor driver
gre: can't add protocol
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Freeing unused kernel memory: 172k freed
offset 0xa000 elapse 4ms
set_action 0


Hit ENTER for console...

clean_mode(1) clean_time(2) threshold(0)
free_caches: Start syncing...
free_caches: Start cleaning...
free_caches: waiting 2 second...
free_caches: Finish.
bootloader version: RT-N14U-01-00-00-01
firmware version: 3.0.0.4
[1 init:init_nvram +9] init_nvram for 4
RT-N14U: swmode: router repeater apconfig_switch(0x00bf): link down all ports
Algorithmics/MIPS FPU Emulator v1.5
config_switch(0x00d3): STB port: 0
config_switch(0x01f2): link up wan port(s)
rt2860v2_ap: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint


=== pAd = c051c000, size = 728632 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.6
hotplug net INTERFACE=ra0 ACTION=add
/ # check_action 0
*** jffs2: 5, 524288
[1 init:init_main +15] main loop signal/state=17
start_logger:
start_usb
_iRaeth v3.0 (fcTaskleton,SkbRecyclefi)
g: na
phy_tx_ring = 0x02ad7000, tx_ring = 0xa2ad7000

phy_rx_ring0 = 0x02ac7000, rx_ring0 = 0xa2ac7000
SMACCR1 -- : 0x00000011
SMACCR0 -- : 0x11111111
meESW: Link Status Changed - Port3 Link Down
=eCDMA_CSG_CFG = 81000000
thGDMA1_FWD_CFG = 20710000
2 flags=1043 IFUP addr=(null) netmask=(null)
hotplug net INTERFACE=vlan1 ACTION=add
hotplug net INTERFACE=vlan2 ACTION=add
start_lan 954
update_lan_state(lan_, 0, 0)
start_lan: setting up the bridge br0
_ifconfig: name=vlan1 flags=1043 IFUP addr=(null) netmask=(null)
start_lan: setting MAC of br0 bridge to 00:11:11:11:11:11
hotplug net INTERFACE=br0 ACTION=add
gen ralRX DESC a2e92000  size = 2048
ink config
gen_ralink_config(0x05bc): Main BSSID is not multiple of 4s!mac_filter[0] = 0
_ifconfig: name=ra0 flags=1043 IFUP addr=(null) netmask=(null)
APSDCapable[0]=1
APSDCapable[1]=1
APSDCapable[2]=1
APSDCapable[3]=1
APSDCapable[4]=1
APSDCapable[5]=1
APSDCapable[6]=1
APSDCapable[7]=1
APSDCapable[8]=1
APSDCapable[9]=1
APSDCapable[10]=1
APSDCapable[11]=1
APSDCapable[12]=1
APSDCapable[13]=1
APSDCapable[14]=1
APSDCapable[15]=1
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
RtmpOSFileOpen(): Error 2 opening /etc_ro/wlan/MT7620_AP_2T2R-4L_V15.BIN
rtmp_ee_init(): rtmp_ee_flash_init() failed
ERROR!!! E2PROM: WRONG VERSION 0xff, should be 1
E2PROM: D0 target power=0xffff
E2PROM: 40 MW Power Delta= 0
3. Phy Mode = 9
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = 2, D2 = 2, CalCode = 0 !!!
RT6352_Temperature_Init : BBPR49 = 0x2
RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff8
Current Temperature from BBP_R49=0xfffffff4
RT6352_TssiTableAdjust: upper_bound = 0x7F decimal: 127
RT6352_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128
*** RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -1 -1 -1 -1 -1 -1 -1
- -1 - -1 -1 -1 -1 -1 -1 -1, offset=-8, tuning=0
RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -9 -9 -9 -9 -9 -9 -9 - -9 - -9 -9 -9 -9 -9 -9 -9, offset=-8, tuning=0
mp_temperature=0xffffffff, step = +7
E2PROM: G Tssi[-7 .. +7] = -9 -9 -9 -9 -9 -9 -9 - -9 - -9 -9 -9 -9 -9 -9 -9, offset=-8, tuning=0
TX BW Filter Calibration !!!
RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= 3, phase=3a)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 0, phase=3d)
TX IQ Calibration Done!
internal ALC is not enabled in NVM !
bAutoTxAgcG = 0
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
Main bssid = 00:11:11:11:11:11
<==== rt28xx_init, Status=0
0x1300 = 00064380
hotplug net INTERFACE=wds3 ACTION=add
hotplug net INTERFACE=wds0 ACTION=add
[doSystem] iwpriv ra0 set TxPower=100
hotplug net INTERFACE=wds1 ACTION=add
hotplug net INTERFACE=wds2 ACTION=add
_ifconfig: name=br0 flags=1043 IFUP addr=192.168.1.1 netmask=255.255.255.0
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
update_lan_state(lan_, 2, 0)

set default filter settings
stop_nat_rules: apply the redirect_rules!
start_lan 1351
start_services 2635
start wsc start_wsc_pin_enrollee()
[doSystem] iwpriv ra0 set WscConfMode=7
WPS: PIN
[doSystem] iwpriv ra0 set WscMode=1
[1 init:start_dnsmasq +23] begin
[1 init:start_dnsmasq +24] end
start_lan_port(0) 1
[doSystem] iwpriv ra0 set WatchdogPid=246
decomp: fname=/var/lib/misc/rstats-speed.gz
set watchdog pid as: 246
[doSystem] iwpriv rai0 set WatchdogPid=246
decomp: gzip -dc /var/lib/misc/rstats-speed.gz > /var/tmp/rstats-uncomp != 0
load: speed_count = 0
load: read source= save_path=
load_history: fname=/var/lib/misc/rstats-history.gz
decomp: fname=/var/lib/misc/rstats-history.gz
decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0
decomp: fname=/var/lib/misc/rstats-history.gz
decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0
load_history: load failed
TZ watchdog
[1 init:start_upnp +25] config 5
start_pptpd: getpid= 1
start_wan_if(0)
update_wan_state(wan0_, 0, 0)
convert_wan_nvram(wan0_)
no linklocal address configured for vlan2
** wan_ifname: vlan2 is NOT UP
_ifconfig: name=vlan2 flags=1043 IFUP addr=(null) netmask=(null)
start_auth:: done
update_wan_state(wan0_, 1, 0)
start_wan_if(): End.
sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
udhcpc_wan:: deconfig
_ifconfig: name=vlan2 flags=1043 IFUP addr=0.0.0.0 netmask=(null)
wan_down(vlan2)
wan_down(vlan2): .
stop_auth:: done
sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
route_manip: cmd=DEL name=vlan2 addr=0.0.0.0 netmask=0.0.0.0 gateway=(null) metric=0
update_wan_state(wan0_, 3, 0)
update_wan_state(wan0_, 4, 3)
udhcpc:: deconfig done
check_action 0
set_action 7
# wanduck: nvram changed: x_Setting=1, link_modem=0.
# wanduck: Got LAN(-1) information:

# Enable direct rule
set_action 0
Started Wireless And Mrbaron.
eval(rtkswitch, 41) ret(0)
ESW: Link Status Changed - Port3 Link UP
U2EC starting ...
eval(iwpriv, ra0, stat) ret(0)
clean_mode(1) clean_time(2) threshold(0)
free_caches: Start syncing...
free_caches: Start cleaning...
free_caches: waiting 2 second...
free_caches: Finish.
[1 init:init_main +30] main loop signal/state=14
Now Make Allowlist
userallowbuf .
[1 init:init_main +31] main loop signal/state=14
udhcpc_wan:: leasefail
Reset Count 1.Current Date 0-0-0.
Mrbaron Gateway.
[1 init:init_main +58] main loop signal/state=14
[3][Sat Jan  1 00:00:58 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t mangle -F WiFiDog_br0_Trusted
[3][Sat Jan  1 00:00:58 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t mangle -F WiFiDog_br0_Outgoing
[3][Sat Jan  1 00:00:58 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t mangle -F WiFiDog_br0_Incoming
[3][Sat Jan  1 00:00:58 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t mangle -X WiFiDog_br0_Trusted
[3][Sat Jan  1 00:00:58 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t mangle -X WiFiDog_br0_Outgoing
[3][Sat Jan  1 00:00:58 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t mangle -X WiFiDog_br0_Incoming
[3][Sat Jan  1 00:00:58 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t nat -F WiFiDog_br0_AuthServers
[3][Sat Jan  1 00:00:58 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t nat -F WiFiDog_br0_Outgoing
[3][Sat Jan  1 00:00:58 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t nat -F WiFiDog_br0_WIFI2Router
[3][Sat Jan  1 00:00:58 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t nat -F WiFiDog_br0_WIFI2Internet
[3][Sat Jan  1 00:00:58 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t nat -F WiFiDog_br0_Global
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t nat -F WiFiDog_br0_Unknown
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t nat -X WiFiDog_br0_AuthServers
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t nat -X WiFiDog_br0_Outgoing
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t nat -X WiFiDog_br0_WIFI2Router
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t nat -X WiFiDog_br0_WIFI2Internet
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t nat -X WiFiDog_br0_Global
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t nat -X WiFiDog_br0_Unknown
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -F WiFiDog_br0_WIFI2Internet
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -F WiFiDog_br0_AuthServers
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -F WiFiDog_br0_Locked
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -F WiFiDog_br0_Global
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -F WiFiDog_br0_Validate
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -F WiFiDog_br0_Known
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -F WiFiDog_br0_Unknown
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -X WiFiDog_br0_WIFI2Internet
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -X WiFiDog_br0_AuthServers
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -X WiFiDog_br0_Locked
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -X WiFiDog_br0_Global
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -X WiFiDog_br0_Validate
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -X WiFiDog_br0_Known
[3][Sat Jan  1 00:00:59 2011][317](fw_iptables.c:116) iptables command failed(1): iptables -t filter -X WiFiDog_br0_Unknown
Accept seq 0.
[3][Sat Jan  1 00:01:01 2011][490](centralserver.c:198) Failed to connect to any of the auth servers
udhcpc_wan:: leasefail
rm: can't remove '/tmp/gw-status.log': No such file or directory
udhcpc_wan:: leasefail
udhcpc_wan:: leasefail
Reset Count 2.Current Date 0-2-2.
udhcpc_wan:: leasefail
udhcpc_wan:: leasefail
[1 init:init_main +206] main loop signal/state=14
udhcpc_wan:: leasefail
Reset Count 3.Current Date 0-3-3.
udhcpc_wan:: leasefail

guolicheng

{:soso_e101:}

guolicheng

ttl 信息有问题吗？ 哪位高手指点下， 怎么中断信息啊。   ctrl+c  ,  p   tpl   都中断不了啊。、

housecall

CPU频率怎么是386，正常是580才对，重新设置一下参数吧

modi5156

hanhg 发表于 2014-10-7 09:41
是的，不然要不死uboot做什么呢？

原来是这样谢谢大神的指点