斐讯K2 V22.3.15.128 启动信息

oppo007

5月份USB-TTL串口线刷了breed r849，最近看到有更新到r899，于是更新到最新的。又闲着蛋疼，breed下刷了官方固件，再更新到V22.3.15.128这一版，官方已下架，确实会把breed干掉。于是按照论坛的开启Telnet的办法，*/1 * * * * iwpriv ra0 e2p 26=7010 && [ "$(ps|grep telnetd|grep -v grep|wc -l)" -lt 2 ] && (killall telnetd_startup;telnetd_startup &)
发现无效，无法开启Telnet。
只能再次用USB-TTL刷breed。
下面是最新的V22.3.15.128启动信息

U-Boot 1.1.3 ( - )

Board: Ralink APSoC DRAM:  64 MB
MT7620 gpio init : WPS / RESET pin
GPIO#1 updated GPIOMODE register: 001a311c -> 001a311d
relocate_code Pointer at: 83fb0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: *********（此处隐藏）
Warning: un-recognized chip ID, please update bootloader!
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:  Time:
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes

Press press hardware button for more than 4 seconds to run web failsafe mode



Catution: hardware button wasn't pressed or not long enough!
Continuing normal boot...


Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   6: Load all then write to Flash via TFTP.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.


3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   OpenWrt-Linux-3.10.14
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1262620 Bytes =  1.2 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

THIS IS ASIC

SDK 5.0.S.0
[    0.000000] Linux version 3.10.14 (jenkins@SOHO-OPWRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 Tue Jul 19 15:26:17 CST 2016
[    0.000000]
[    0.000000]  The CPU feqenuce set to 580 MHz
[    0.000000]  PCIE: bypass PCIe DLL.
[    0.000000]  PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
[    0.000000]  disable all power about PCIe
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] Software DMA cache coherency
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00066005
[    0.000000] Readback ErrCtl register=00066005
[    0.000000] Memory: 61020k/65536k available (2784k kernel code, 4516k reserved, 656k data, 204k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] console [ttyS1] enabled
[    0.108000] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[    0.148000] pid_max: default: 32768 minimum: 301
[    0.152000] Mount-cache hash table entries: 512
[    0.156000] NET: Registered protocol family 16
[    0.160000] RALINK_GPIOMODE = 1a311d
[    0.164000] RALINK_GPIOMODE = 18311d
[    0.168000] PPLL_CFG1=0xe6c000
[    0.172000] MT7620 PPLL lock
[    0.176000] PPLL_DRV =0x80080504
[    0.180000] start PCIe register access
[    0.680000] RALINK_RSTCTRL = 2400000
[    0.684000] RALINK_CLKCFG1 = 75afffc0
[    0.688000]
[    0.688000] *************** MT7620 PCIe RC mode *************
[    1.188000] PCIE0 enabled
[    1.192000] Port 0 N_FTS = 1b105000
[    1.196000] init_rt2880pci done
[    1.220000] bio: create slab <bio-0> at 0
[    1.224000] PCI host bridge to bus 0000:00
[    1.228000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    1.232000] pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
[    1.236000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.240000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.244000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[    1.248000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[    1.252000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[    1.256000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[    1.260000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[    1.264000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[    1.268000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.272000] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
[    1.276000] pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
[    1.280000] BAR0 at slot 0 = 0
[    1.284000] bus=0x0, slot = 0x0
[    1.288000] res[0]->start = 0
[    1.292000] res[0]->end = 0
[    1.296000] res[1]->start = 20200000
[    1.300000] res[1]->end = 2020ffff
[    1.304000] res[2]->start = 0
[    1.308000] res[2]->end = 0
[    1.312000] res[3]->start = 0
[    1.316000] res[3]->end = 0
[    1.320000] res[4]->start = 0
[    1.324000] res[4]->end = 0
[    1.328000] res[5]->start = 0
[    1.332000] res[5]->end = 0
[    1.336000] bus=0x1, slot = 0x0
[    1.340000] res[0]->start = 20000000
[    1.344000] res[0]->end = 200fffff
[    1.348000] res[1]->start = 0
[    1.352000] res[1]->end = 0
[    1.356000] res[2]->start = 0
[    1.360000] res[2]->end = 0
[    1.364000] res[3]->start = 0
[    1.368000] res[3]->end = 0
[    1.372000] res[4]->start = 0
[    1.376000] res[4]->end = 0
[    1.380000] res[5]->start = 0
[    1.384000] res[5]->end = 0
[    1.388000] Switching to clocksource Ralink Systick timer
[    1.392000] NET: Registered protocol family 2
[    1.404000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    1.416000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    1.428000] TCP: Hash tables configured (established 512 bind 512)
[    1.440000] TCP: reno registered
[    1.448000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.460000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.472000] NET: Registered protocol family 1
[    1.480000] Load Kernel WDG Timer Module
[    1.488000] Load Ralink Timer0 Module
[    1.500000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.512000] jffs2: version 2.2. (NAND) (SUMMARY)  (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.532000] msgmni has been set to 119
[    1.540000] io scheduler noop registered (default)
[    1.548000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.560000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
[    1.576000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
[    1.588000] button_netlink: create netlink socket ok.
[    1.600000] Ralink gpio driver initialized
[    1.608000] Enable Ralink GDMA Controller Module
[    1.616000] GDMA IP Version=3
[    1.624000] spidrv_major = 217
[    1.628000] deice id : c8 40 17 c8 40 (4017c840)
[    1.640000] Warning: un-recognized chip ID, please update SPI driver!
[    1.652000] GD25Q64B(c8 40170000) (8192 Kbytes)
[    1.660000] mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
[    1.680000] Creating 5 MTD partitions on "raspi":
[    1.692000] 0x000000000000-0x000000800000 : "ALL"
[    1.700000] 0x000000000000-0x000000030000 : "Bootloader"
[    1.712000] 0x000000030000-0x000000040000 : "Config"
[    1.724000] 0x000000040000-0x000000050000 : "Factory"
[    1.736000] 0x000000050000-0x000000800000 : "firmware"
[    1.748000] 0x00000018445c-0x000000800000 : "rootfs"
[    1.756000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.784000] mtd: partition "rootfs_data" created automatically, ofs=0x6e0000, len=0x120000
[    1.800000] 0x0000006e0000-0x000000800000 : "rootfs_data"
[    1.812000] rdm_major = 253
[    1.820000] netif_napi_add() called with weight 128 on device eth0
[    1.832000] SMACCR1 -- : 0x00008cab
[    1.836000] SMACCR0 -- : 0x8eafee39
[    1.844000] Ralink APSoC Ethernet Driver Initilization. v3.1  512 rx/tx descriptors allocated, mtu = 1500!
[    1.864000] NAPI enable, Tx Ring = 512, Rx Ring = 512
[    1.872000] SMACCR1 -- : 0x00008cab
[    1.880000] SMACCR0 -- : 0x8eafee39
[    1.888000] PROC INIT OK!
[    1.896000] Ralink APSoC Hardware Watchdog Timer
[    1.904000] TCP: cubic registered
[    1.912000] NET: Registered protocol family 10
[    1.920000] NET: Registered protocol family 17
[    1.928000] 8021q: 802.1Q VLAN Support v1.8
[    1.936000] init_module:price_compare!
[    1.944000] creat nlsock ok!
[    1.956000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.972000] Freeing unused kernel memory: 204K (8035d000 - 80390000)

Kucami

不懂，看楼下怎么说

cjt200685

小白表示完全看不懂