[7月16日更新-本帖终结]AX6砖了，官方和ttl都失败，请大神们帮忙！！！

solomongao

7,16 更新
在查看TTL信息时发现里面有一条

1. U-Boot 2016.01 (Jul 06 2020 - 10:50:19 +0000), Build: jenkins-r3600_ota_publish-152

复制代码

想了下，似乎是当时用官方修复时选错了文件，把u-boot刷成了r3600，也就是AX36000的固件，索性用官方修复刷了3600的“miwifi_r3600_firmware_d1610_1.1.21.bin”，然后……
发生了一个不算奇迹的奇迹，刷完后Internet竟然开始闪蓝灯
只是目前的问题是断电重启后Internet竟然开始闪橙灯，结束后system蓝灯一闪，然后不断的重复上面的过程，这种状态下自然也无法用过web或ssh方式进行修复，索性开机后长按reset清空系统设置，再断电重启情况依旧……
再试下ttl…………成功进入。
后面按

1. https://www.right.com.cn/FORUM/thread-8253621-1-8.html

复制代码

成功救砖
按

1. https://www.right.com.cn/FORUM/forum.php?mod=viewthread&tid=8291501&highlight=u%2Bboot%2BAX6

复制代码

刷入不死UBOOT
至此，AX6完美复活！！本帖终结，完美撒花！！


7.14 记录
AX6按https://www.right.com.cn/forum/thread-8236039-3-1.html救砖失败，又按https://www.right.com.cn/FORUM/thread-4717648-1-2.html用ttl救砖也失败，
现在的情况是开机后sys灯亮几秒灭掉，之后intern亮一下，然后两灯都灭了，不停的循环这个状态，用官方修砖是可以走完进度的，但刷完长亮紫灯不灭，彻底没辙了
ttl下既无法按回车停止boot，系统也没法继续执行程序，用ttl查跑码结果如下，查了论坛也没发现有类似情况，请各路大神帮忙：

1. Connecting to COM3...
   
2. Connected.
   
3. 
   
4. jªM        D+ check, Start
   
5. D -         0 - USB D+ check, Delta
   
6. B -    825879 - SBL1, End
   
7. D -    680607 - SBL1, Delta
   
8. S - Flash Throughput, 6753 KB/s  (2096379 Bytes,  310423 us)
   
9. S - DDR Frequency, 466 MHz
   
10. S - Core 0 Frequency, 800 MHz
    
11. 
    
12. 
    
13. U-Boot 2016.01 (Jul 06 2020 - 10:50:19 +0000), Build: jenkins-r3600_ota_publish-152
    
14. 
    
15. DRAM:  smem ram ptable found: ver: 1 len: 4
    
16. 512 MiB
    
17. NAND:  ONFI device found
    
18. ID = 158061c8
    
19. Vendor = c8
    
20. Device = 61
    
21. SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
    
22. ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
    
23. 128 MiB
    
24. MMC:   sdhci: Node Not found, skipping initialization
    
25. 
    
26. ## Error: flags type check failure for "ethaddr" <= ""00:AA:BB:CC:DD:10"" (type: m)
    
27. himport_r: can't insert "ethaddr="00:AA:BB:CC:DD:10"" into hash table
    
28. PCI1 is not defined in the device tree
    
29. In:    serial@78B3000
    
30. Out:   serial@78B3000
    
31. Err:   serial@78B3000
    
32. machid: 8010010
    
33. MMC Device 0 not found
    
34. eth5 MAC Address from ART is not valid
    
35. write phy_id=1, reg(0x8074):0x0670
    
36. write phy_id=2, reg(0x8074):0x0670
    
37. write phy_id=3, reg(0x8074):0x0670
    
38. write phy_id=4, reg(0x8074):0x0670
    
39. bootwait is off, bootdelay=5
    
40. Hit any key to stop autoboot:  0
    
41. trigger button release!
    
42. boot from rootfs 1
    
43.   miwifi: check crash in rmem !  
    
44. ubi0: attaching mtd1
    
45. ubi0: scanning is finished
    
46. ubi0: attached mtd1 (name "mtd=0", size 66 MiB)
    
47. ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
    
48. ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
    
49. ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
    
50. ubi0: good PEBs: 532, bad PEBs: 0, corrupted PEBs: 0
    
51. ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
    
52. ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 33712689
    
53. ubi0: available PEBs: 284, total reserved PEBs: 248, PEBs reserved for bad PEB handling: 20
    
54. Read 0 bytes from volume kernel to 44000000
    
55. No size specified -> Using max size (4317184)
    
56. Could not find PCI in device tree
    
57. ## Loading kernel from FIT Image at 44000000 ...
    
58.    Using 'config@ac04' configuration
    
59.    Trying 'kernel@1' kernel subimage
    
60.      Description:  ARM64 OpenWrt Linux-4.4.60
    
61.      Type:         Kernel Image
    
62.      Compression:  gzip compressed
    
63.      Data Start:   0x440000e8
    
64.      Data Size:    3957924 Bytes = 3.8 MiB
    
65.      Architecture: AArch64
    
66.      OS:           Linux
    
67.      Load Address: 0x41080000
    
68.      Entry Point:  0x41080000
    
69.      Hash algo:    crc32
    
70.      Hash value:   d807269a
    
71.      Hash algo:    sha1
    
72.      Hash value:   9b765627ec30dbf10507b430b78eeac59423ba9a
    
73.    Verifying Hash Integrity ... crc32+ sha1+ OK
    
74. ## Loading fdt from FIT Image at 44000000 ...
    
75.    Using 'config@ac04' configuration
    
76.    Trying 'fdt@ac04' fdt subimage
    
77.      Description:  ARM64 OpenWrt qcom-ipq807x-hkxx device tree blob
    
78.      Type:         Flat Device Tree
    
79.      Compression:  uncompressed
    
80.      Data Start:   0x443edb18
    
81.      Data Size:    79565 Bytes = 77.7 KiB
    
82.      Architecture: AArch64
    
83.      Hash algo:    crc32
    
84.      Hash value:   b4ed9ff8
    
85.      Hash algo:    sha1
    
86.      Hash value:   6119388eb1ae982f4a3586f267c7ea804db115bb
    
87.    Verifying Hash Integrity ... crc32+ sha1+ OK
    
88.    Booting using the fdt blob at 0x443edb18
    
89.    Uncompressing Kernel Image ... OK
    
90.    Loading Device Tree to 4a3e9000, end 4a3ff6cc ... OK
    
91. Using machid 0x8010010 from environment
    
92. 
    
93. Starting kernel ...
    
94. 
    
95. Jumping to AARCH64 kernel via monitor
    
96. [    0.000000] Booting Linux on physical CPU 0x0
    
97. [    0.000000] Initializing cgroup subsys cpuset
    
98. [    0.000000] Initializing cgroup subsys cpu
    
99. [    0.000000] Initializing cgroup subsys cpuacct
    
100. [    0.000000] Linux version 4.4.60 (jenkins@16c0d7b27833) (gcc version 5.5.0 (OpenWrt GCC 5.5.0 unknown) ) #0 SMP PREEMPT Fri Mar 5 08:59:31 2021
     
101. [    0.000000] Boot CPU: AArch64 Processor [410fd034]
     
102. [    0.000000] Ignoring memory range 0x40000000 - 0x41000000
     
103. [    0.000000] efi: Getting EFI parameters from FDT:
     
104. [    0.000000] efi: UEFI not found.
     
105. [    0.000000] psci: probing for conduit method from DT.
     
106. [    0.000000] psci: PSCIv1.0 detected in firmware.
     
107. [    0.000000] psci: Using standard PSCI v0.2 function IDs
     
108. [    0.000000] psci: MIGRATE_INFO_TYPE not supported.
     
109. [    0.000000] PERCPU: Embedded 14 pages/cpu @ffffffc01ef5c000 s19096 r8192 d30056 u57344
     
110. [    0.000000] Detected VIPT I-cache on CPU0
     
111. [    0.000000] CPU features: enabling workaround for ARM erratum 845719
     
112. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 105840
     
113. [    0.000000] Kernel command line: ubi.mtd=rootfs_1 root=mtd:ubi_rootfs rootfstype=squashfs rootwait swiotlb=1
     
114. [    0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes)
     
115. [    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
     
116. [    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
     
117. [    0.000000] software IO TLB [mem 0x5fe58000-0x5fe98000] (0MB) mapped at [ffffffc01ee58000-ffffffc01ee97fff]
     
118. [    0.000000] Memory: 402208K/430080K available (5491K kernel code, 654K rwdata, 2796K rodata, 224K init, 405K bss, 27872K reserved, 0K cma-reserved)
     
119. [    0.000000] Virtual kernel memory layout:
     
120. [    0.000000]     vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000   (   246 GB)
     
121. [    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
     
122. [    0.000000]               0xffffffbdc0040000 - 0xffffffbdc0800000   (     7 MB actual)
     
123. [    0.000000]     fixed   : 0xffffffbffa7fd000 - 0xffffffbffac00000   (  4108 KB)
     
124. [    0.000000]     PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000   (    16 MB)
     
125. [    0.000000]     modules : 0xffffffbffc000000 - 0xffffffc000000000   (    64 MB)
     
126. [    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc01f000000   (   496 MB)
     
127. [    0.000000]       .init : 0xffffffc00089a000 - 0xffffffc0008d2000   (   224 KB)
     
128. [    0.000000]       .text : 0xffffffc000080000 - 0xffffffc0008997f4   (  8294 KB)
     
129. [    0.000000]       .data : 0xffffffc0008e1000 - 0xffffffc000984800   (   654 KB)
     
130. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
     
131. [    0.000000] Preemptible hierarchical RCU implementation.
     
132. [    0.000000]         Build-time adjustment of leaf fanout to 64.
     
133. [    0.000000] NR_IRQS:64 nr_irqs:64 0
     
134. [    0.000000] Architected cp15 timer(s) running at 19.20MHz (virt).
     
135. [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
     
136. [    0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
     
137. [    0.000397] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
     
138. [    0.000409] pid_max: default: 32768 minimum: 301
     
139. [    0.000497] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
     
140. [    0.000506] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes)
     
141. [    0.001039] Initializing cgroup subsys io
     
142. [    0.001055] Initializing cgroup subsys memory
     
143. [    0.001085] Initializing cgroup subsys devices
     
144. [    0.001100] Initializing cgroup subsys freezer
     
145. [    0.001112] Initializing cgroup subsys net_cls
     
146. [    0.001122] Initializing cgroup subsys pids
     
147. [    0.001371] EFI services will not be available.
     
148. [    0.001396] ASID allocator initialised with 65536 entries
     
149. [    0.051862] MSM Memory Dump base table set up
     
150. [    0.051886] MSM Memory Dump apps data table set up
     
151. [    0.090120] Detected VIPT I-cache on CPU1
     
152. [    0.090163] CPU1: Booted secondary processor [410fd034]
     
153. [    0.120105] Detected VIPT I-cache on CPU2
     
154. [    0.120133] CPU2: Booted secondary processor [410fd034]
     
155. [    0.150133] Detected VIPT I-cache on CPU3
     
156. [    0.150160] CPU3: Booted secondary processor [410fd034]
     
157. [    0.150212] Brought up 4 CPUs
     
158. [    0.150238] SMP: Total of 4 processors activated.
     
159. [    0.150247] CPU: All CPU(s) started at EL1
     
160. [    0.150271] alternatives: patching kernel code
     
161. [    0.167043] DMI not present or invalid.
     
162. [    0.167292] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
     
163. [    0.167316] futex hash table entries: 1024 (order: 5, 131072 bytes)
     
164. [    0.167541] pinctrl core: initialized pinctrl subsystem
     
165. [    0.168482] NET: Registered protocol family 16
     
166. [    0.190063] cpuidle: using governor ladder
     
167. [    0.220079] cpuidle: using governor menu
     
168. [    0.220219] vdso: 2 pages (1 code @ ffffffc0008e9000, 1 data @ ffffffc0008e8000)
     
169. [    0.220359] DMA: preallocated 256 KiB pool for atomic allocations
     
170. [    0.220453] CPU: unavail, SoC Version: 2.0
     
171. [    0.220490] <CORE> glink_init: IPC Logging Disabled
     
172. [    0.220887] IPC logging disabled
     
173. [    0.220893] IPC logging disabled
     
174. [    0.220898] IPC logging disabled
     
175. [    0.220902] IPC logging disabled
     
176. [    0.220907] IPC logging disabled
     
177. [    0.223610] Soc version is not 1, changing clock offsets
     
178. [    0.235016] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
     
179. [    0.237033] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
     
180. [    0.239211] msm_rpm_dev_probe: APSS-RPM communication over GLINK
     
181. [    0.240132] sps:sps is ready.
     
182. [    0.249859] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 2
     
183. [    0.256365] pps_core: LinuxPPS API ver. 1 registered
     
184. [    0.256377] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
     
185. [    0.256400] PTP clock support registered
     
186. [    0.256556] dmi: Firmware registration failed.
     
187. [    0.257837] Advanced Linux Sound Architecture Driver Initialized.
     
188. [    0.258485] clocksource: Switched to clocksource arch_sys_counter
     
189. [    0.261734] NET: Registered protocol family 2
     
190. [    0.262329] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
     
191. [    0.262389] TCP bind hash table entries: 4096 (order: 4, 65536 bytes)
     
192. [    0.262486] TCP: Hash tables configured (established 4096 bind 4096)
     
193. [    0.262535] UDP hash table entries: 256 (order: 1, 8192 bytes)
     
194. [    0.262558] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
     
195. [    0.262730] NET: Registered protocol family 1
     
196. [    0.270361] squashfs: version 4.0 (2009/01/31) Phillip Lougher
     
197. [    0.270379] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
     
198. [    0.273636] io scheduler noop registered
     
199. [    0.273652] io scheduler deadline registered (default)
     
200. [    0.275687] 20000000.pci supply vdda not found, using dummy regulator
     
201. [    0.275764] 20000000.pci supply vdda_phy not found, using dummy regulator
     
202. [    0.275800] 20000000.pci supply vdda_refclk not found, using dummy regulator
     
203. [    0.276351] PCI host bridge /soc/pci@20000000 ranges:
     
204. [    0.276379]    IO 0x20200000..0x202fffff -> 0x20200000
     
205. [    0.276394]   MEM 0x20300000..0x20ffffff -> 0x20300000
     
206. [    1.308533] qcom-pcie 20000000.pci: phy link never came up
     
207. [    1.310076] qcom-pcie 20000000.pci: hostinit failed
     
208. [    1.310086] qcom-pcie 20000000.pci: cannot initialize host
     
209. [    1.310231] qcom-pcie: probe of 20000000.pci failed with error -110
     
210. [    1.315565] NET: Registered protocol family 27
     
211. [    1.315577] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled
     
212. [    1.315590] qmi_log_init: IPC Logging disabled
     
213. [    1.315595] qmi_log_init: IPC Logging disabled
     
214. [    1.315680] msm_rpm_log_probe: OK
     
215. [    1.316248] msm-dcc b3000.dcc: DCC XPU is not specified
     
216. [    1.316491] msm-dcc b3000.dcc: DCC SRAM dump setup failed
     
217. [    1.316515] msm-dcc b3000.dcc: jiffies_64: 0xffff8b52, cntvct_64: 0x6905cc7
     
218. [    1.316526] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xffffff80003cc004)
     
219. [    1.316536] msm-dcc b3000.dcc: gcnt_lo: 0x06905e77(0xffffff80003cc000)
     
220. [    1.317064] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set
     
221. [    1.317701] msm_serial 78b3000.serial: msm_serial: detected port #0
     
222. [    1.317736] msm_serial 78b3000.serial: uartclk = 3686400
     
223. [    1.317769] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 77, base_baud = 230400) is a MSM
     
224. [    1.317787] msm_serial: console setup on port #0
     
225. [    2.053476] console [ttyMSM0] enabled
     
226. [    2.058426] msm_serial 78b1000.serial: msm_serial: detected port #1
     
227. [    2.061722] msm_serial 78b1000.serial: uartclk = 19200000
     
228. [    2.067778] 78b1000.serial: ttyMSM1 at MMIO 0x78b1000 (irq = 78, base_baud = 1200000) is a MSM
     
229. [    2.073633] msm_serial: driver initialized
     
230. [    2.082098] msm_serial_hsl_init: driver initialized
     
231. [    2.094829] brd: module loaded
     
232. [    2.095508] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
     
233. [    2.098186] m25p80 spi32766.0: unrecognized JEDEC id bytes: 00,  0,  0
     
234. [    2.105105] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x61
     
235. [    2.110358] nand: GigaDevice PSR1GA30DT
     
236. [    2.116822] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
     
237. [    2.120504] 15 ofpart partitions found on MTD device qcom_nand.0
     
238. [    2.128024] Creating 15 MTD partitions on "qcom_nand.0":
     
239. [    2.134203] 0x000000000000-0x000000100000 : "0:SBL1"
     
240. [    2.141164] 0x000000100000-0x000000200000 : "0:MIBIB"
     
241. [    2.145956] 0x000000200000-0x000000500000 : "0:QSEE"
     
242. [    2.152719] 0x000000500000-0x000000580000 : "0:DEVCFG"
     
243. [    2.155484] 0x000000580000-0x000000600000 : "0:RPM"
     
244. [    2.160453] 0x000000600000-0x000000680000 : "0:CDT"
     
245. [    2.165213] 0x000000680000-0x000000700000 : "0:APPSBLENV"
     
246. [    2.170083] 0x000000700000-0x000000800000 : "0:APPSBL"
     
247. [    2.176067] 0x000000800000-0x000000880000 : "0:ART"
     
248. [    2.180709] 0x000000880000-0x000000900000 : "bdata"
     
249. [    2.185429] 0x000000900000-0x000000980000 : "crash"
     
250. [    2.190279] 0x000000980000-0x000000a00000 : "crash_syslog"
     
251. [    2.195140] 0x000000a00000-0x000002dc0000 : "rootfs"
     
252. [    2.232138] mtd: device 12 (rootfs) set to be root filesystem
     
253. [    2.232485] mtdsplit: no squashfs found in "rootfs"
     
254. [    2.236866] 0x000002dc0000-0x000007040000 : "rootfs_1"
     
255. [    2.301133] 0x000007040000-0x0000070c0000 : "rsvd0"
     
256. [    2.302723] spmi spmi-0: PMIC Arb Version-2 (0x20010000)
     
257. [    2.307665] libphy: Fixed MDIO Bus: probed
     
258. [    2.531049] qca-mdio 90000.mdio: Could not find phy-reset-gpio
     
259. [    2.531155] libphy: qca_mdio: probed
     
260. [    2.536987] qca-mdio 90000.mdio: qca-mdio driver was registered
     
261. [    2.539711] Unable to create IPC log context!
     
262. [    2.545433] cnss: Platform driver probed successfully.
     
263. [    2.549896] Skip QCA8074V1 in V2 platform
     
264. [    2.554790] cnss_genl: genl_register_family fail: -17
     
265. [    2.558816] cnss: CNSS genl init failed -17
     
266. [    2.563798] cnss: Platform driver probed successfully.
     
267. [    2.567940] i2c /dev entries driver
     
268. [    2.579469] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
     
269. [    2.579930] sdhci: Secure Digital Host Controller Interface driver
     
270. [    2.586966] sdhci: Copyright(c) Pierre Ossman
     
271. [    2.592984] sdhci-pltfm: SDHCI platform and OF driver helper
     
272. [    2.598030] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed
     
273. [    2.603184] ICE IRQ = 81
     
274. [    2.611684]
     
275. [    2.611684] Version Rollback Feature Disabled
     
276. [    2.614628] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000008b04000
     
277. [    2.619631] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000008b04000
     
278. [    2.636896] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000008b04000
     
279. [    2.652779] sps:BAM 0x0000000008b04000 is registered.[    2.660507] DEV CI test message
     
280. [    2.665211] subsys-restart: ssr_parse_restart_orders(): q6v5_m3 device has been added to q6v5-m3's restart group
     
281. [    2.667970] subsys-restart: ssr_parse_restart_orders(): q6v5_wcss device has been added to q6v5-m3's restart group
     
282. [    2.678485] remoteproc remoteproc0: q6v5-m3 is available
     
283. [    2.688895] SPMI VADC - Min ch: 0 Max ch: 15
     
284. [    2.695672] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000
     
285. [    2.698331] coresight-csr 6001000.csr: CSR initialized
     
286. [    2.705794] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000
     
287. [    2.710752] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000
     
288. [    2.718275] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000
     
289. [    2.725672] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000
     
290. [    2.733044] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000
     
291. [    2.740426] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000
     
292. [    2.747791] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000
     
293. [    2.755183] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000
     
294. [    2.762565] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000
     
295. [    2.769935] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000
     
296. [    2.777314] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000
     
297. [    2.784697] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000
     
298. [    2.792079] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000
     
299. [    2.799456] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000
     
300. [    2.806819] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000
     
301. [    2.814213] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000
     
302. [    2.821595] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000
     
303. [    2.829137] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000
     
304. [    2.836454] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000
     
305. [    2.843881] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000
     
306. [    2.851296] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000
     
307. [    2.858674] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000006044000
     
308. [    2.865706] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000006044000
     
309. [    2.882815] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000006044000
     
310. [    2.898700] sps:BAM 0x0000000006044000 is registered.[    2.906324] coresight-tmc 6028000.tmc: TMC initialized
     
311. [    2.911139] coresight-tmc 6027000.tmc: TMC initialized
     
312. [    2.916269] coresight-funnel 6021000.funnel: FUNNEL initialized
     
313. [    2.921330] coresight-funnel 6100000.funnel: FUNNEL initialized
     
314. [    2.927119] coresight-funnel 6120000.funnel: FUNNEL initialized
     
315. [    2.933048] coresight-funnel 61a1000.funnel: FUNNEL initialized
     
316. [    2.939471] coresight-etm4x 619c000.etm: ETM 4.0 initialized
     
317. [    2.945158] coresight-etm4x 619d000.etm: ETM 4.0 initialized
     
318. [    2.951110] coresight-etm4x 619e000.etm: ETM 4.0 initialized
     
319. [    2.956776] coresight-etm4x 619f000.etm: ETM 4.0 initialized
     
320. [    2.962065] coresight-replicator-qcom 6026000.replicator: REPLICATOR 1.0 initialized
     
321. [    2.967789] coresight-stm 6002000.stm: STM initialized
     
322. [    2.976330] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000
     
323. [    2.980227] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized
     
324. [    2.990461] Netfilter messages via NETLINK v0.30.
     
325. [    2.995424] ip_set: protocol 6
     
326. [    3.000720] NET: Registered protocol family 10
     
327. [    3.003723] NET: Registered protocol family 17
     
328. [    3.007403] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
     
329. [    3.011854] Bridge firewalling registered
     
330. [    3.024567] 8021q: 802.1Q VLAN Support v1.8
     
331. [    3.029957] <CORE> glink_core_register_transport: IPC Logging disabled
     
332. [    3.032563] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 2
     
333. [    3.039077] msm_glink_smem_native_xprt        rx fifo not found
     
334. [    3.046412] pmd9655_s3: supplied by e-smps1-reg
     
335. [    3.052026] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
     
336. [    3.056066] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
     
337. [    3.062680] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
     
338. [    3.070327] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
     
339. [    3.077820] cpr3_mem_acc_init: apc: not using memory accelerator regulator
     
340. [    3.086983] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      SVS: open-loop= 704000 uV
     
341. [    3.093928] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      NOM: open-loop= 816000 uV
     
342. [    3.103959] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      SVS: quot[ 7]= 708, quot_offset[ 7]=   0
     
343. [    3.113725] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      NOM: quot[ 7]= 925, quot_offset[ 7]= 215
     
344. [    3.124673] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
     
345. [    3.136785] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz
     
346. [    3.142388] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017600 KHz
     
347. [    3.149655] DEV CI test message
     
348. [    3.158456] remoteproc remoteproc1: q6v5-wcss is available
     
349. [    3.161238] ubi0: attaching mtd13
     
350. [    3.512309] random: nonblocking pool is initialized
     
351. [    3.513014] ubi0: scanning is finished
     
352. [    3.522776] ubi0: attached mtd13 (name "rootfs_1", size 66 MiB)
     
353. [    3.522797] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
     
354. [    3.527491] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
     
355. [    3.534447] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
     
356. [    3.541299] ubi0: good PEBs: 532, bad PEBs: 0, corrupted PEBs: 0
     
357. [    3.548062] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
     
358. [    3.554322] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 33712689
     
359. [    3.561357] ubi0: available PEBs: 284, total reserved PEBs: 248, PEBs reserved for bad PEB handling: 20
     
360. [    3.570304] ubi0: background thread "ubi_bgt0d" started, PID 117
     
361. [    3.590302] hctosys: unable to open rtc device (rtc0)
     
362. [    3.615466]  crash_kernel_init, res rsvd1, 50700000, 400000, /reserved-memory/rsvd1@50700000  
     
363. [    3.615500]  mtd dev crash, size 0x80000
     
364. [    3.623380]  crash_kernel_init,  crash init, res->start:50700000,crash_buf:0xffffff8001c80000,crash_buf_len 0x7ffe4, crash_avail_sz 0x80000
     
365. [    3.627054]  Crash kernel dumper registered ok!
     
366. [    3.639758]  crash_syslog_init, res rsvd2, 50b00000, 400000, /reserved-memory/rsvd2@50b00000  
     
367. [    3.644237]  mtd dev crash_syslog, size 0x80000
     
368. [    3.653377]  crash_syslog_init,  crash init, crash_buf_len 0x3ffe4, crash_avail_sz 0x40000  
     
369. [    3.657528]  Crash syslog dumper register ok!
     
370. [    3.665978] pmd9655_ldo11: disabling
     
371. [    3.670700] ALSA device list:
     
372. [    3.673910]   No soundcards found.
     
373. [    3.679434] VFS: Mounted root (squashfs filesystem) readonly on device 31:16.
     
374. [    3.680217] Freeing unused kernel memory: 224K (ffffffc00089a000 - ffffffc0008d2000)
     
375. [    3.687307] Freeing alternatives memory: 44K (ffffffc0008d2000 - ffffffc0008dd000)
     
376. [    4.038205] init: Console is alive
     
377. [    4.038322] init: - watchdog -
     
378. [    5.160264] kmodloader: loading kernel modules from /etc/modules-boot.d/*
     
379. [    5.176322] usbcore: registered new interface driver usbfs
     
380. [    5.176375] usbcore: registered new interface driver hub
     
381. [    5.180815] usbcore: registered new device driver usb
     
382. [    5.187533] Button Hotplug driver version 0.4.1
     
383. [    5.193630] SCSI subsystem initialized
     
384. [    5.197317] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
     
385. [    5.199837] ehci-platform: EHCI generic platform driver
     
386. [    5.418386] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
     
387. [    5.418426] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
     
388. [    5.422953] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x00010010
     
389. [    5.430360] xhci-hcd xhci-hcd.0.auto: irq 189, io mem 0x08a00000
     
390. [    5.439424] hub 1-0:1.0: USB hub found
     
391. [    5.445253] hub 1-0:1.0: 1 port detected
     
392. [    5.448998] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
     
393. [    5.452884] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
     
394. [    5.458217] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
     
395. [    5.466058] hub 2-0:1.0: USB hub found
     
396. [    5.474079] hub 2-0:1.0: 1 port detected
     
397. [    5.480365] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
     
398. [    5.490549] init: - preinit -
     
399. Press the [f] key and hit [enter] to enter failsafe mode
     
400. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
     
401. [    8.860621] mount_root: mounting /dev/root
     
402. hexdump: /tmp/ubi_data_firstpage.bin: No such file or directory
     
403. rm: can't remove '/tmp/ubi_data_firstpage.bin': No such file or directory
     
404. flag_format_overlay is set, format
     
405. ubiattach: error!: strtoul: unable to parse the number ''
     
406. ubiattach: error!: bad MTD device number: ""
     
407. cat: can't open '/sys/class/ubi/ubi1/dev': No such file or directory
     
408. cat: can't open '/sys/class/ubi/ubi1/dev': No such file or directory
     
409. BusyBo[    8.935375] UBIFS error (pid: 198): cannot open "ubi1_0", error -19x v1.25.1 (2021-03-08 11:34:02 UTC) multi-call binary.
     
410. 
     
411. Usage: mknod [-m MODE] NAME TYPE MAJOR MINOR
     
412. 
     
413. Create a special file (block, character, or pipe)
     
414. 
     
415.         -m MODE        Creation mode (default a=rw)
     
416. TYPE:
     
417.         b        Block device
     
418.         c or u        Character device
     
419.         p        Named pipe (MAJOR and MINOR are ignored)
     
420. libubi: error!: cannot get information about "/dev/ubi1"
     
421.         error 2 (No such file or directory)
     
422. ubimkvol: error!: error while probing "/dev/ubi1"
     
423.           error 2 (No such file or directory)
     
424. mount: mounting ubi1_0 on /data failed: No such device
     
425. Trying to save syslog to crash...
     
426. target mtd /dev/mtd10
     
427. MTD Type: 4
     
428. MTD total size: 80000 bytes
     
429. MTD erase size: 20000 bytes
     
430. Beging Eraseing Block 0x400f28
     
431. End...
     
432. Unlocking crash ...
     
433. 
     
434. Writing from /tmp/.mtd_crash_tmp to crash ...     
     
435. Log saved to crash.
     
436. FATAL: Data mount fail again. Restoring defaults.
     
437. ubiattach: error!: strtoul: unable to parse the number ''
     
438. ubiat
     
439. [    9.367616] UBIFS error (pid: 210): cannot open "ubi1_0", error -19tach: error!: bad MTD device number: ""
     
440. mount: mounting ubi1_0 on /data failed: No such device
     
441. [    9.432

复制代码

到[ 9.432就没有下文了，不是粘贴不全

xiaodong-l

boot进不去，是不是boot搞坏了？我遇到过一次紫灯的情况，后面就没出现过。

solomongao

5290589 发表于 2024-7-14 12:17
boot进不去，是不是boot搞坏了？我遇到过一次紫灯的情况，后面就没出现过。 ...

就是搞不清楚是因为什么，手边也没编程器，只有ttl，无奈了

1562004423

参考教程：
https://www.right.com.cn/forum/thread-8255711-1-1.html
https://www.right.com.cn/FORUM/thread-8255773-1-1.html

solomongao

1562004423 发表于 2024-7-14 14:38
参考教程：
https://www.right.com.cn/forum/thread-8255711-1-1.html
https://www.right.com.cn/FORUM/thr ...

感谢，但我刷完官方并不会出现蓝灯闪烁，只是紫灯一直亮

1562004423

solomongao 发表于 2024-7-14 14:46
感谢，但我刷完官方并不会出现蓝灯闪烁，只是紫灯一直亮

你们怎么总是喜欢看灯呢，灯有什么用，接上ttl，看有没有输出，看报错在哪里，看能不能操作，看点有用的

solomongao

试了N次，ttl都是快速跳过autoboot，没办法阻止运行内核……