找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 8122|回复: 30

FON2405E有没有改过USB供电的?成本需要多少???

[复制链接]
如题,TB上看FON2405E最近价格不贵,想买一台看看,不知道有没有人改过USB供电,这样地话可以随时通过电脑或者的机充电器供电了...

这里有拆解图:

https://www.right.com.cn/forum/f ... hread&tid=51019
 楼主| | 显示全部楼层
高淫都上哪去了???
回复

使用道具 举报

剪开USB延长线之类的线 取USB带线,线另一头剪开 取正负极 焊接好5.5插头就好了  做了一条成本2~5元吧。。
回复

使用道具 举报

这机器。。。
5V 1A最少的了。。。没啥玩头,不带usb,openwrt是能跑的,但是目前没人专门编译,没有wan口,没啥意思,早玩过了
回复

使用道具 举报

 楼主| | 显示全部楼层
zhujunsq 发表于 2012-10-23 08:42
这机器。。。
5V 1A最少的了。。。没啥玩头,不带usb,openwrt是能跑的,但是目前没人专门编译,没有wan ...

USB可以接出来的,有USB触点...

OP好像也有人编译吧,RT3050F的...

不是原生自带单WAN单LAN么,咋没WAN???
回复

使用道具 举报

邪恶海盗 发表于 2012-10-23 09:43
USB可以接出来的,有USB触点...

OP好像也有人编译吧,RT3050F的...

我的意思是得有人编译固件才有的玩,,,
回复

使用道具 举报

 楼主| | 显示全部楼层
zhujunsq 发表于 2012-10-23 13:18
我的意思是得有人编译固件才有的玩,,,

有第三方固件刷就行了,不求多少功能,只求稳定...
回复

使用道具 举报

邪恶海盗 发表于 2012-10-23 21:53
有第三方固件刷就行了,不求多少功能,只求稳定...

有个ranlink的公版固件,英文界面,复位也支持,稳定性还行
回复

使用道具 举报

 楼主| | 显示全部楼层
zhujunsq 发表于 2012-10-23 21:56
有个ranlink的公版固件,英文界面,复位也支持,稳定性还行

发来瞧瞧...

支持WEB升级还是TTL???
回复

使用道具 举报

回复

使用道具 举报

 楼主| | 显示全部楼层
zhujunsq 发表于 2012-10-23 22:31
http://royalwin.blog.so-net.ne.jp/2011-12-20按照这个刷就是了

TTL刷的...

鸟文的还是不爱好啊...
回复

使用道具 举报


U-Boot 1.1.3 (Jan  6 2010 - 07:10:30)

Board: Fonera
DRAM:  32 MB
relocate_code Pointer at: 81fac000
spi_wait_nsec: 3e
spi deice id: c2 20 15 c2 20 (2015c220)
find flash: mx25l1605d
raspi_read: from:41030000 len:1000
Using default environment


##### The CPU freq = 320 MHZ ####

SDRAM bus set to 16 bit
SDRAM size =32 Mbytes

Please choose the operation:
   1: Boot system code via Flash (default).
   2: Load system code then write to Flash via TFTP.
   3: Entr boot command line interface.

booting from flash
## Booting image at bf020000 ...
raspi_read: from:20000 len:40
   Image Name:   FON Linux-2.6.21
   Created:      2011-07-11  17:10:36 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    646362 Bytes = 631.2 kB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:20040 len:9dcda
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32

Starting kernel ...


LINUX started...

THIS IS ASIC
Linux version 2.6.21 (eduardo@veriton) (gcc version 4.1.2) #1 Mon Jul 11 19:10:30 CEST 2011

The CPU feqenuce set to 320 MHz
CPU revision is: 0001964c
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 80800064, status = 1100ff00
PID hash table entries: 128 (order: 7, 512 bytes)
calculating r4koff... 0030d400(3200000)
CPU frequency 320.00 MHz
Using 160.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 30312k/32768k available (1783k kernel code, 2456k reserved, 192k data, 100k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Fonita
Generic PHY: Registered new driver
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered
io scheduler deadline registered (default)
ramips_wdt: loaded
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
PPP generic driver version 2.4.2
NET: Registered protocol family 24
IMQ starting with 2 devices...
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
deice id : c2 20 15 c2 20 (2015c220)
MX25L1605D(c2 2015c220) (2048 Kbytes)
mtd .name = raspi, .size = 0x00200000 (2M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
ramips_mtd: kernel size is 646426
padded kernel is 0009E000
Creating 6 MTD partitions on "raspi":
0x00000000-0x00010000 : "uboot"
0x00010000-0x00020000 : "boardconfig"
0x00020000-0x001f0000 : "image"
0x00020000-0x000be000 : "linux"
mtd: partition "linux" doesn't end on an erase block -- force read-only
0x000be000-0x001f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
mtd: partition "rootfs" set to be root filesystem
0x001f0000-0x00200000 : "uci_overlay"
Registered led device: power
Registered led device: wps
Registered led device: wlan
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ramips_gpio: done
ramips: ethernet loaded
ramips_eth: loaded
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 100k freed
Warning: unable to open an initial console.
Preinit complete, spawning microd
  _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M

Bonita Fonita (svn unknown) ---------------------------

starting MEGABOOM vortex engine
Detected a FON2405
copying file from /etc/default/whitelist to /tmp/whitelist
found uci_overlaAlgorithmics/MIPS FPU Emulator v1.5
y -> /dev/mtd5
preparing factory uci settings
copying file from /etc/config_default/zepttho to /tmp/uci_overlay/zepttho
copying file from /etc/config_default/wireless to /tmp/uci_overlay/wireless
copying file from /etc/config_default/user to /tmp/uci_overlay/user
copying file from /etc/config_default/uresd to /tmp/uci_overlay/uresd
copying file from /etc/config_default/uddns to /tmp/uci_overlay/uddns
copying file from /etc/config_default/reg to /tmp/uci_overlay/reg
copying file from /etc/config_default/qos to /tmp/uci_overlay/qos
copying file from /etc/config_default/network to /tmp/uci_overlay/network
copying file from /etc/config_default/led to /tmp/uci_overlay/led
copying file from /etc/config_default/lang to /tmp/uci_overlay/lang
copying file from /etc/config_default/form to /tmp/uci_overlay/form
copying file from /etc/config_default/fonsmcd to /tmp/uci_overlay/fonsmcd
copying file from /etc/config_default/fon to /tmp/uci_overlay/fon
copying file from /etc/config_default/firewall to /tmp/uci_overlay/firewall
copying file from /etc/config_default/features to /tmp/uci_overlay/features
copying file from /etc/default/passwd to /tmp/passwd
copying file from /etc/default/chilli.conf.FON2405 to /tmp/chilli.conf
copying file from /etc/default/localusers to /tmp/localusers
copying file from /etc/default/whitelist to /tmp/whitelist
uci : core
uci : features
uci : lang
uci : essid
uci : wifi
uci : channel
uci : mtu
uci : country
uci : http_wifi
uci : http_11d
uci : http_tls
uci : bridge
uci : repeater
4.0.2.3 -> 4.0.2.3
loading fon config
forking watched process syslogd with pid 14
registering led wps -> /sys/class/leds/wps/
registering led wlan -> /sys/class/leds/wlan/
registering led power -> /sys/class/leds/power/
Configuring switch
loading base firewall ...done
syslog: Mar  4 14:39:15 syslog: adding zone wannet
syslog: Mar  4 14:39:16 syslog: adding zone lan
syslog: Mar  4 14:39:16 syslog: adding zone wan
syslog: Mar  4 14:39:16 syslog: adding zone hotspotwifi
syslog: Mar  4 14:39:16 syslog: adding zone hotspot
syslog: Mar  4 14:39:16 syslog: adding forwarding lan->wan
wifi device rt305x
  type = rt305x
  channel = 11
  mode = 9
wifi interface public
  ifname = ra1
  ssid = FON_FREE_INTERNET
  encryption = none
  network = hotspotwifi
  device = rt305x
  isolate = 1
  auto = 1
  ht = HT20
  wps = pbc
  country = JP
wifi interface private
  ifname = ra0
  ssid = MyPlace_689B28
  encryption = wpa2
  key = 4141414141
  password = oogohsohxo
  wpa_crypto = aes
  network = lan
  device = rt305x
  channel = 0
  mode = bgn
  txpower = 100
  ht = HT20
  wps = pbc
  country = JP
syslog: Mar  4 14:39:16 syslog: bringing up rt305x
rt2860v2_ap: module license 'unspecified' taints kernel.
interface loopback
  proto = static
  ipaddr = 127.0.0.1
  netmask = 255.0.0.0
  ifname = lo
interface lan
  proto = static
  ipaddr = 192.168.10.1
  netmask = 255.255.255.0
  ifname = eth0.1
  type = bridge
interface wan
  proto = dhcp
  ifname = eth0.2
interface hotspot
  ifname = tun0
interface hotspotwifi
  proto = none
  ifname = ra1
syslog: Mar  4 14:39:17 syslog: net event up loopback
syslog: Mar  4 14:39:17 syslog: bringing up lo
done
syslog: Mar  4 14:39:17 syslog: net event up leth0.1: dev_set_promiscuity(master, 1)
an
syslog: Mardevice eth0 entered promiscuous mode
  4 14:39:17 sysdevice eth0.1 entered promiscuous mode
log: bringing upbr-lan: port 1(eth0.1) entering learning state
eth0.1
syslog: Mar  4 14:39:17 syslog: adding br-lan to zone lan
done
syslog: Mar  4 14:39:18 syslog: net event up wan
syslog: Mar  4 14:39:18 syslog: bringing up eth0.2
Configuring switch - wan/lan
syslog: Mar  4 14:39:18 syslog: Spawning udhcpc for eth0.2
syslog: Mar  4 14:39:18 syslog: adding eth0.2 to zone wan
udhcpc (v0.9.9-pre) started
syslog: Mar  4 14:39:18 udhcpc[206]: udhcpc (v0.9.9-pre) started
Trying to connect...
sending -> "udhcpc|deconfig|eth0.2|"
switch reg write offset=40, value=1002
Sending discover...
done
回复

使用道具 举报

TTL里面的信息就这样
但是web里面还是官方那个页面
真不晓得是怎么回事
还没有找到合适的固件
不如就耍了 DD或者OP
回复

使用道具 举报

 楼主| | 显示全部楼层
本帖最后由 邪恶海盗 于 2012-12-22 23:30 编辑
benly 发表于 2012-12-22 22:16
TTL里面的信息就这样
但是web里面还是官方那个页面
真不晓得是怎么回事

RT3050F+2M+32M变态货...

mx25l1605d,这个就是Flash型号,8脚SPI...


Tenda W311r V6.5和268R某版本的配置为RT3050F+2M+8M,估计能刷,有编程器不怕砖地话可以试试看...


参考此帖:腾达W311R(811R)V6.5 无线路由器RT3050F_1M Flash_8M内存缩水版编程器固件(点击查看)
回复

使用道具 举报

邪恶海盗 发表于 2012-12-22 23:25
RT3050F+2M+32M变态货...

mx25l1605d,这个就是Flash型号,8脚SPI...

看到ttl信息里面有openwrt 的 logo 。。。很南明哦。。
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

欢迎大家光临恩山无线论坛上一条 /1 下一条

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-5-23 17:13

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表