极壹s ttl线刷 报错 求指导 ethernet: port0 linkdown(dev event...

gy31***

ttl信息如下：
一直就是
[  521.660000] ethernet: port0 linkdown(dev event)
[  521.810000] device eth2.2 entered promiscuous mode
无限循环

U-Boot 1.1.3 (Dec 31 2014 - 13:19:08)

Board: Ralink APSoC DRAM:  128 MB
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi device id: ef 40 18 0 0 (40180000)
find flash: w25q128
*** Warning - bad CRC, using default environment

============================================
ASIC 7620_MP (Port5<->None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
Dateec 31 2014  Time:13:19:08
============================================
0
## Booting image at bc050000 ...
   Image Name:   HC5661
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1417086 Bytes =  1.4 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.3.8 (build@DEV-9-1-243) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Thu Jan 29 13:34:04 CST 2015
[    0.000000]
[    0.000000]  The CPU feqenuce set to 580 MHz
[    0.000000]
[    0.000000]  MIPS CPU sleep mode enabled.
[    0.000000]  PCIE: bypass PCIe DLL.
[    0.000000]  PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
[    0.000000]  disable all power about PCIe
[    0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00008000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00008000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=HC5661 console=ttyS1,115200 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=0000000e
[    0.000000] Readback ErrCtl register=0000000e
[    0.000000] allocated 262144 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 125628k/131072k available (2739k kernel code, 5444k reserved, 610k data, 372k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:128
[    0.000000] MTK/Ralink System Tick Counter init... cd:80333ba0, m:214748, s:32
[    0.000000] console [ttyS1] enabled
[    0.010000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 512
[    0.080000] Initializing cgroup subsys memory
[    0.080000] Initializing cgroup subsys net_cls
[    0.090000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is Hiwifi Wireless HC5661 Board
[    0.100000] gpiochip_add: registered GPIOs 0 to 23 on device: MT7620-GPIO0
[    0.100000] gpiochip_add: registered GPIOs 24 to 39 on device: MT7620-GPIO1
[    0.110000] gpiochip_add: registered GPIOs 40 to 71 on device: MT7620-GPIO2
[    0.110000] gpiochip_add: registered GPIOs 72 to 72 on device: MT7620-GPIO3
[    1.310000] PCIE0 no card, disable it(RST&CLK)
[    1.320000] bio: create slab <bio-0> at 0
[    1.330000] PCI host bridge to bus 0000:00
[    1.330000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    1.340000] pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
[    1.340000] Switching to clocksource Ralink external timer
[    1.350000] NET: Registered protocol family 2
[    1.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    1.360000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    1.370000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    1.370000] TCP: Hash tables configured (established 4096 bind 4096)
[    1.380000] TCP reno registered
[    1.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.400000] NET: Registered protocol family 1
[    1.750000] RT3xxx EHCI/OHCI init.
[    1.770000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.780000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.790000] msgmni has been set to 245
[    1.800000] io scheduler noop registered
[    1.800000] io scheduler deadline registered (default)
[    1.810000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.810000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
[    1.820000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
[    1.840000] brd: module loaded
[    1.840000] deice id : ef 40 18 0 0 (40180000)
[    1.850000] chip info: w25q128(ef 40180000)
[    1.850000] mtd name = raspi, size = 0x01000000 (16M) erasesize = 0x00010000 (64K)
[    1.860000] raspi: squash filesystem found at block 27
[    1.880000] bdinfo: fac txt empty, use default.
[    1.880000] Creating 9 MTD partitions on "raspi":
[    1.890000] 0x000000000000-0x000000030000 : "u-boot"
[    1.890000] mtdchar alloc 0x10000 memory success
[    1.900000] 0x000000030000-0x000000040000 : "hw_panic"
[    1.910000] 0x000000040000-0x000000050000 : "Factory"
[    1.910000] 0x000000050000-0x0000001b0000 : "kernel"
[    1.920000] 0x0000001b0000-0x000000fd0000 : "rootfs"
[    1.930000] mtd: partition "rootfs" set to be root filesystem
[    1.930000] mtd: partition "rootfs_data" created automatically, ofs=C40000, len=390000
[    1.940000] 0x000000c40000-0x000000fd0000 : "rootfs_data"
[    1.950000] 0x000000fd0000-0x000000fe0000 : "hwf_config"
[    1.960000] 0x000000fe0000-0x000000ff0000 : "bdinfo"
[    1.960000] 0x000000ff0000-0x000001000000 : "backup"
[    1.970000] 0x000000050000-0x000000fd0000 : "firmware"
[    1.980000] Stopped WatchDog Timer.
[    1.980000] Ralink APSoC Hardware Watchdog Timer
[    1.990000] MTK MSDC device init.
[    1.990000] MediaTek MT6575 MSDC Driver
[    2.000000] TCP cubic registered
[    2.000000] NET: Registered protocol family 17
[    2.010000] 8021q: 802.1Q VLAN Support v1.8
[    2.010000] Freeing unused kernel memory: 372k freed
-HiWiFi initrd-
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
keypressed: 1
- regular preinit -
[    7.500000] JFFS2 notice: (511) jffs2_build_xattr_subsystem: complete building xattr subsystem, 29 of xdatum (1 unchecked, 28 orphan) and 72 of xref (0 dead, 61 orphan) found.
switching to jffs2
- init -
[   10.410000] Uniform Multi-Platform E-IDE driver
[   10.590000] NET: Registered protocol family 10
[   10.980000] SCSI subsystem initialized
[   11.110000] usbcore: registered new interface driver usbfs
[   11.120000] usbcore: registered new interface driver hub
[   11.120000] usbcore: registered new device driver usb
[   11.210000] zram: Created 1 device(s) ...
[   11.930000] rt2860v2_ap: module license 'unspecified' taints kernel.
[   11.940000] Disabling lock debugging due to kernel taint
[   13.030000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[   13.440000] loop: module loaded
[   13.610000] PPP generic driver version 2.4.2
[   13.660000] PPP MPPE Compression module registered
[   13.680000] IPv6 over IPv4 tunneling driver
[   13.780000] exFAT: Core Version 1.2.4
[   13.800000] exFAT: FS Version 1.2.4
[   13.870000] GRE over IPv4 demultiplexor driver
[   13.960000] GRE over IPv4 tunneling driver
[   13.980000] ide-gd driver 1.18
[   14.160000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.430000] NET: Registered protocol family 24
[   14.670000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   14.690000] rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
[   14.700000] rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
[   14.740000] rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
[   14.760000] rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
[   14.760000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   14.770000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   14.780000] usb usb1: Product: Ralink EHCI Host Controller
[   14.780000] usb usb1: Manufacturer: Linux 3.3.8 ehci_hcd
[   14.790000] usb usb1: SerialNumber: rt3xxx
[   14.790000] hub 1-0:1.0: USB hub found
[   14.800000] hub 1-0:1.0: 1 port detected
[   14.950000] nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
[   15.530000] PPTP driver version 0.8.5
[   15.920000] xt_time: kernel timezone is -0000
[   16.530000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   16.870000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   16.900000] rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
[   16.910000] rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
[   16.920000] rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
[   16.980000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[   16.990000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   16.990000] usb usb2: Product: RT3xxx OHCI Controller
[   17.000000] usb usb2: Manufacturer: Linux 3.3.8 ohci_hcd
[   17.000000] usb usb2: SerialNumber: rt3xxx-ohci
[   17.010000] hub 2-0:1.0: USB hub found
[   17.010000] hub 2-0:1.0: 1 port detected
[   17.120000] Initializing USB Mass Storage driver...
[   17.130000] usbcore: registered new interface driver usb-storage
[   17.130000] USB Mass Storage support registered.
[   17.220000] fuse init (API version 7.18)

[   28.830000] device eth2 entered promiscuous mode
[   28.850000] br-lan: port 1(eth2.1) entered forwarding state
[   28.850000] br-lan: port 1(eth2.1) entered forwarding state
鴁@^@^@[   29.480000] ADDRCONF(NETDEV_CHANGE): eth2.1: link becomes ready
^@^@^@[   30.540000] device eth2.2 entered promiscuous mode
[   30.850000] br-lan: port 1(eth2.1) entered forwarding state
^@^@^@@^@^@^@[   36.070000] device ra0 entered promiscuous mode
[   36.080000] br-lan: port 2(ra0) entered forwarding state
[   36.080000] br-lan: port 2(ra0) entered forwarding state
[   36.260000] Simple address matching list for Netfilter - HiWiFi
[   38.080000] br-lan: port 2(ra0) entered forwarding state
[   43.580000] [NOTICE] <HWF-Kproxy> (hwf_kproxy_init:2121) kproxy hook prioriy -101
[   43.590000] [NOTICE] <HWF-Kproxy> (hwf_kproxy_init:2155) Module is inserted
[   44.500000] [NOTICE] <HWF-SQOS> (hwf_sqos_lan_init:120) lan: 192.168.199.1, lan1: 0.0.0.0
[   44.510000] [NOTICE] <HWF-SQOS> (hwf_sqos_init:186) Module is inserted
[   45.740000] [NOTICE] <HWF-SQOS> (hwf_sqos_qdisc_init:347) tc direction  1
[   45.750000] [NOTICE] <HWF-SQOS> (hwf_sqos_qdisc_init:348) tc queue len max 4000
[   45.880000] [NOTICE] <HWF-SQOS> (hwf_sqos_qdisc_init:347) tc direction  0
[   45.890000] [NOTICE] <HWF-SQOS> (hwf_sqos_qdisc_init:348) tc queue len max 4000
[   49.030000] device eth2.2 left promiscuous mode
[   49.070000] ethernet: port0 linkdown(dev event)
[   49.500000] device eth2.2 entered promiscuous mode
[   66.830000] device eth2.2 left promiscuous mode
[   66.860000] ethernet: port0 linkdown(dev event)
[   67.010000] device eth2.2 entered promiscuous mode
[   83.540000] device eth2.2 left promiscuous mode
[   83.550000] ethernet: port0 linkdown(dev event)
[   83.710000] device eth2.2 entered promiscuous mode
[  100.260000] device eth2.2 left promiscuous mode
[  100.270000] ethernet: port0 linkdown(dev event)
[  100.440000] device eth2.2 entered promiscuous mode
[  116.950000] device eth2.2 left promiscuous mode
[  116.980000] ethernet: port0 linkdown(dev event)
[  117.140000] device eth2.2 entered promiscuous mode
[  133.660000] device eth2.2 left promiscuous mode

gy31***

顶一顶，，求大神指导

era***

极路由1S增强版，在不ROOT的情况下，TTL通讯模式成功更新hack大的不死uboot
话说极路由锁uboot蛮彻底的，uboot的刷机选项全没了

gy31***

eraghjk 发表于 2015-3-21 17:43
极路由1S增强版，在不ROOT的情况下，TTL通讯模式成功更新hack大的不死uboot
话说极路由锁uboot蛮彻底的，u ...

我按着Ctrl+C键  没有反应啊。

gy31***

顶顶，把顶上去，让更多人看到

ABTCa***

膜拜，顶一下

era***

gy3141255 发表于 2015-3-21 18:17
我按着Ctrl+C键  没有反应啊。

[    0.000000] Linux version 3.3.8 (build@DEV-9-1-243) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Thu Jan 29 13:34:04 CST 2015

看固件的编译日期是2015.01.29，这可能是最新版本的固件封了TTL，要想办法降级到9006/9007