|
|
以下是部分启动输出：
U-Boot 1.1.3 (Dec 25 2014 - 13:53:24)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer at: 87fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
find flash: W25Q128BV
size = 16MB, sector size = 64KB, 256 sectors
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.2.S.1
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: SPI Flash
Date ec 25 2014 Time:13:53:24
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size = 128 Mbytes
## Booting image at bc080000 ...
raspi_read: from:80000 len:40
Image Name: MIPS OpenWrt Linux-3.10.14-p1128
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1227055 Bytes = 1.2 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:80040 len:12b92f
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
怘?奦??x臸怘怘ff斆旦f[ 0.000000] Linux version 3.10.14 (james@localhost.localdomain) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #18 Tue Jan 13 16:51:05 CST 2015
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 580 MHz
[ 0.000000] PCIE: bypass PCIe DLL.
[ 0.000000] PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
[ 0.000000] disable all power about PCIe
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock6 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=0003b657
[ 0.000000] Readback ErrCtl register=0003b657
[ 0.000000] Memory: 125724k/131072k available (2692k kernel code, 5348k reserved, 654k data, 172k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled
[ 0.110000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.170000] pid_max: default: 32768 minimum: 301
[ 0.170000] Mount-cache hash table entries: 512
[ 0.180000] NET: Registered protocol family 16
[ 0.180000] RALINK_GPIOMODE = 1a311c
[ 0.190000] RALINK_GPIOMODE = 18311c
[ 0.190000] PPLL_CFG1=0xe64000
[ 0.190000] MT7620 PPLL lock
[ 0.190000] PPLL_DRV =0x80080504
[ 0.200000] start PCIe register access
[ 0.700000] RALINK_RSTCTRL = 2400000
[ 0.700000] RALINK_CLKCFG1 = 75afffc0
[ 0.710000]
[ 0.710000] *************** MT7620 PCIe RC mode *************
[ 1.210000] PCIE0 no card, disable it(RST&CLK)
[ 1.220000] PCIE0 enabled
[ 1.220000] Port 0 N_FTS = ffffffff
[ 1.220000] init_rt2880pci done
[ 1.250000] bio: create slab <bio-0> at 0
[ 1.250000] PCI host bridge to bus 0000:00
[ 1.260000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[ 1.260000] pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff]
[ 1.270000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.270000] Switching to clocksource MIPS
[ 1.280000] NET: Registered protocol family 2
[ 1.280000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 1.290000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 1.300000] TCP: Hash tables configured (established 1024 bind 1024)
[ 1.300000] TCP: reno registered
[ 1.310000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.310000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.320000] NET: Registered protocol family 1
[ 1.320000] MTK/Ralink EHCI/OHCI init.
[ 1.350000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.350000] NTFS driver 2.1.30 [Flags: R/W].
[ 1.360000] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 1.370000] msgmni has been set to 245
[ 1.370000] io scheduler noop registered
[ 1.380000] io scheduler deadline registered (default)
[ 1.380000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 1.390000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
[ 1.400000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
[ 1.400000] Ralink gpio driver initialized
[ 1.410000] Enable Ralink GDMA Controller Module
[ 1.410000] GDMA IP Version=3
[ 1.420000] spidrv_major = 217
[ 1.420000] deice id : ef 40 18 0 0 (40180000)
[ 1.430000] W25Q128BV(ef 40180000) (16384 Kbytes)
[ 1.430000] mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 256
[ 1.440000] Creating 6 MTD partitions on "raspi":
[ 1.450000] 0x000000000000-0x000001000000 : "ALL"
[ 1.450000] 0x000000000000-0x000000030000 : "Bootloader"
[ 1.460000] 0x000000030000-0x000000040000 : "Config"
[ 1.470000] 0x000000040000-0x000000050000 : "Factory"
[ 1.470000] 0x000000050000-0x000000080000 : " roduct"
[ 1.480000] 0x000000080000-0x000000800000 : "firmware"
[ 1.490000] 0x0000001ab96f-0x000000800000 : "rootfs" |
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡