wr941n v2 16M flash的uboot

729650915

RT
还没测试(没环境)
试过的帮忙反馈下

chkai1981

感谢楼主分享，第一时间下载，呵呵

yzl0827

感谢楼主分享，第二时间下载，呵呵

Grelon

沙发没有坐上

729650915

刚刚又合成了个编程器固件 下载地址在顶楼

chkai1981

我合成的固件是英文的，用的是楼主提供的factory那个固件，不知是不是我哪里搞的不对呀

729650915

6# chkai1981

我的固件是英文的 没集成中文包 需要自己装

chkai1981

能不能集成一下呢，呵呵。我自己不会弄。最好在加点软件，比如下载啥的


flash容量识别这样，对吗？

wtchen

第一时间下载研究

729650915

8# chkai1981


...好像不正常 难道我漏了啥参数...? 有ttl的发下启动信息看看

rickyo0

1# 729650915


恭喜LZ终于发现编译uboot当初的问题所在了
你一开始用的是最新的4.5版本吧
你再-ver看看现在编译成功所用的版本号多少
没记错的话是3.4
所以我说你是版本有问题
你和我说软件没问题啊
我说你没开窍
这源码应该是atheros基于当时的3.4版本的gcc写的
用现在最新的gcc编译问题就出来了

chkai1981

U-Boot 1.1.4 (Apr  7 2011 - 18:59:04)

AP81 (ar7100) U-boot by dyq
DRAM:  
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 256
Flash: 16 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Autobooting in 1 seconds, press t to stop## Booting image at bf020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.37.6 (dyq@dyq-desktop) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #2 Wed Apr 6 23:17:24 CST 2011
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
Atheros AR9132 rev 1, CPU:400.000 MHz, AHB:100.000 MHz, DDR:400.000 MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line:  board=TL-WR941ND rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29492k/32768k available (1924k kernel code, 3276k reserved, 366k data, 168k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:56
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR941ND
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: found mx25l12805d, expected m25p80
m25p80 spi0.0: mx25l12805d (16384 Kbytes)
Searching for RedBoot partition table in spi0.0 at offset 0xfe0000
Searching for RedBoot partition table in spi0.0 at offset 0xff0000
No RedBoot partition table detected in spi0.0
spi0.0: no WRT160NL signature found
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000160000 : "kernel"
0x000000160000-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=5F0000, len=200000
0x0000005f0000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "art"
0x000000020000-0x0000007f0000 : "firmware"
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registered
NET: Registered protocol family 17
Distributed Switch Architecture driver version 0.1
eth0[0]: detected a Marvell 88E6060 switch
dsa slave smi: probed
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 168k freed
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.4.1
eth0: link up (100Mbps/Full duplex)
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -
eth0: link down

Please press Enter to activate this console. eth0: link up (100Mbps/Full duplex)
device lan1 entered promiscuous mode
device eth0 entered promiscuous mode
device lan2 entered promiscuous mode
device lan3 entered promiscuous mode
device lan4 entered promiscuous mode
Compat-wireless backport release: compat-wireless-2011-01-31-26-gf7606f5
Backport based on wireless-testing.git master-2011-03-24
cfg80211: Calling CRDA to update world regulatory domain
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
cfg80211: World regulatory domain updated:
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
usbcore: registered new device driver usb
ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a1 mem=0xb80c0000, irq=2
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
nf_conntrack version 0.5.0 (463 buckets, 1852 max)
xt_time: kernel timezone is -0000
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
JFFS2 notice: (1577) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
lan2: link up, 100 Mb/s, full duplex, flow control disabled
br-lan: port 2(lan2) entering forwarding state
br-lan: port 2(lan2) entering forwarding state
wan: link up, 100 Mb/s, full duplex, flow control disabled
eth0: link down
br-lan: port 2(lan2) entering forwarding state
device eth0 left promiscuous mode
device lan4 left promiscuous mode
br-lan: port 4(lan4) entering disabled state
device lan3 left promiscuous mode
br-lan: port 3(lan3) entering disabled state
device lan2 left promiscuous mode
br-lan: port 2(lan2) entering disabled state
device lan1 left promiscuous mode
br-lan: port 1(lan1) entering disabled state
lan2: link down
wan: link down
eth0: link up (100Mbps/Full duplex)
eth0: link down
eth0: link up (100Mbps/Full duplex)
device lan1 entered promiscuous mode
device eth0 entered promiscuous mode
device lan2 entered promiscuous mode
device lan3 entered promiscuous mode
device lan4 entered promiscuous mode
wan: link up, 100 Mb/s, full duplex, flow control disabled
lan2: link up, 100 Mb/s, full duplex, flow control disabled
br-lan: port 2(lan2) entering forwarding state
br-lan: port 2(lan2) entering forwarding state
device wlan0 entered promiscuous mode
br-lan: port 5(wlan0) entering forwarding state
br-lan: port 5(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 5(wlan0) entering forwarding state
device wlan0 entered promiscuous mode
br-lan: port 5(wlan0) entering forwarding state
br-lan: port 5(wlan0) entering forwarding state

729650915

11# rickyo0
弄了半天发现gpl里自带编译工具....甚蛋疼 昨天find命令发现的

12# chkai1981
看来能认到16M flash了 但openwrt的分区好像有问题...估计哪个参数搞错了

rickyo0

13# 729650915


没事 当初我也走过这个弯路
用最新的gcc搞了几次不成功
后来检查源码的时候突然想到是不是GCC版本的问题
然后google顺利解决
我们还是有点像的
我现在的和路由有关的知识 不论是路由的使用 还是编译固件或者uboot
基本99%都是自己埋头翻论坛帖子和google思考
再加上自己实践得来的

rickyo0

不过这样也挺有成就感