360V6 刷机求助

lyr***

刷UBOOT后进Uboot正常，无论刷什么固件都不能进系统。
TTL执行 tftpboot 360v6.bin && flash rootfs 0x44000000 $filesize后可以进系统界面，升级/重置/重启后都不能进系统，TTL信息如下。
T T BOOTP broadcast 最多等到过90多，似乎会一直这样循环下去。


不知道是不是Uboot没刷好，请大神帮忙看看有什么办法挽救。



Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00077-IPQ60xxLZB-2
S - IMAGE_VARIANT_STRING=IPQ6018LA
S - OEM_IMAGE_VERSION_STRING=crm-ubuntu64
S - Boot Interface: NAND
S - Secure Boot: Off
S - Boot Config @ 0x000a602c = 0x000002e5
S - JTAG ID @ 0x000a607c = 0x001390e1
S - OEM ID @ 0x000a6080 = 0x00000000
S - Serial Number @ 0x000a4128 = 0x3d2a057d
S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000
S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000
S - Feature Config Row 0 @ 0x000a4130 = 0x0000800018200021
S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e83783000009
S - PBL Patch Ver: 1
S - I-cache: On
S - D-cache: On
B -      3413 - PBL, Start
B -       592 - bootable_media_detect_entry, Start
B -      4339 - bootable_media_detect_success, Start
B -      5207 - elf_loader_entry, Start
B -      5380 - auth_hash_seg_entry, Start
B -      7847 - auth_hash_seg_exit, Start
B -      8343 - elf_segs_hash_verify_entry, Start
B -    110492 - elf_segs_hash_verify_exit, Start
B -    114917 - auth_xbl_sec_hash_seg_entry, Start
B -    115060 - auth_xbl_sec_hash_seg_exit, Start
B -    121611 - xbl_sec_segs_hash_verify_entry, Start
B -    121611 - xbl_sec_segs_hash_verify_exit, Start
B -    122541 - PBL, End
B -    103303 - SBL1, Start
B -    243390 - GCC [RstStat:0x0, RstDbg:0x600000] WDog Stat : 0x4
B -    245830 - clock_init, Start
D -      2653 - clock_init, Delta
B -    254309 - boot_flash_init, Start
D -     29951 - boot_flash_init, Delta
B -    287554 - sbl1_ddr_set_default_params, Start
D -       244 - sbl1_ddr_set_default_params, Delta
B -    294172 - boot_config_data_table_init, Start
D -      4758 - boot_config_data_table_init, Delta - (575 Bytes)
B -    303993 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:2,Subtype:0
B -    308843 - Image Load, Start
D -      6618 - OEM_MISC Image Loaded, Delta - (0 Bytes)
B -    318176 - Image Load, Start
D -      5063 - PMIC Image Loaded, Delta - (0 Bytes)
B -    326045 - sbl1_ddr_set_params, Start
B -    331016 - CPR configuration: 0x366
B -    334219 - Pre_DDR_clock_init, Start
D -       183 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta
B -    370819 - Image Load, Start
D -       458 - APDP Image Loaded, Delta - (0 Bytes)
B -    383903 - Image Load, Start
D -       458 - QTI_MISC Image Loaded, Delta - (0 Bytes)
B -    386343 - Image Load, Start
D -       824 - Auth Metadata
D -       640 - Segments hash check
D -     22357 - QSEE Dev Config Image Loaded, Delta - (36354 Bytes)
B -    410682 - Image Load, Start
D -      6710 - Auth Metadata
D -     10584 - Segments hash check
D -    335805 - QSEE Image Loaded, Delta - (1470632 Bytes)
B -    746914 - Image Load, Start
D -       732 - Auth Metadata
D -       915 - Segments hash check
D -     34983 - RPM Image Loaded, Delta - (102664 Bytes)
B -    783575 - Image Load, Start
D -       671 - Auth Metadata
D -      2989 - Segments hash check
D -    116937 - APPSBL Image Loaded, Delta - (537240 Bytes)
B -    916128 - SBL1, End
D -    813130 - SBL1, Delta
S - Flash Throughput, 4000 KB/s  (2148137 Bytes,  430593 us)
S - Core 0 Frequency, 800 MHz
S - DDR Frequency, 466 MHz


U-Boot 2016.01 (Jan 29 2023 - 04:31:36 +0000)

DRAM:  smem ram ptable found: ver: 2 len: 4
512 MiB
NAND:  ONFI device found
ID = 9500a1ef
Vendor = ef
Device = a1
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
PCI0 is not defined in the device tree
In:    serial@78B1000
Out:   serial@78B1000
Err:   serial@78B1000
machid: 8030200
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
eth2 MAC Address from ART is not valid
eth3 MAC Address from ART is not valid
eth4 MAC Address from ART is not valid
eth5 MAC Address from ART is not valid

Net:   MAC0 addr:0:3:7f:ba:db:ad
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (0-0)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq6018_edma_alloc_rings: successfull
ipq6018_edma_setup_ring_resources: successfull
ipq6018_edma_configure_rings: successfull
ipq6018_edma_hw_init: successfull
eth0
Hit any key to stop autoboot:  0
ipq6018_eth_halt: done
eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 up Speed :1000 Full duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
ipq6018_eth_init: done
BOOTP broadcast 1
T T T T T BOOTP broadcast 2
T T BOOTP broadcast 3
T T BOOTP broadcast 4
T T BOOTP broadcast 5
T T BOOTP broadcast 6
T T BOOTP broadcast 7
T T BOOTP broadcast 8
T T BOOTP broadcast 9
T T BOOTP broadcast 10
T T BOOTP broadcast 11
T T BOOTP broadcast 12
T T BOOTP broadcast 13
T T BOOTP broadcast 14
T T BOOTP broadcast 15
T T BOOTP broadcast 16
T T BOOTP broadcast 17
T T BOOTP broadcast 18
T T BOOTP broadcast 19
T T BOOTP broadcast 20
T T BOOTP broadcast 21
T T BOOTP broadcast 22


按ctrl+C  中断 BOOTP broadcast后，再输入bootipq就能进系统。

wr8***

https://github.com/breeze303/OpenWrt

lyr***

U-Boot 2016.01 (Jan 29 2023 - 04:31:36 +0000)

DRAM:  smem ram ptable found: ver: 2 len: 4
512 MiB
NAND:  ONFI device found
ID = 9500a1ef
Vendor = ef
Device = a1
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
PCI0 is not defined in the device tree
In:    serial@78B1000
Out:   serial@78B1000
Err:   serial@78B1000
machid: 8030200
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
eth2 MAC Address from ART is not valid
eth3 MAC Address from ART is not valid
eth4 MAC Address from ART is not valid
eth5 MAC Address from ART is not valid

Net:   MAC0 addr:0:3:7f:ba:db:ad
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (0-0)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq6018_edma_alloc_rings: successfull
ipq6018_edma_setup_ring_resources: successfull
ipq6018_edma_configure_rings: successfull
ipq6018_edma_hw_init: successfull
eth0
Hit any key to stop autoboot:  0
IPQ6018# setenv ipaddr 192.168.1.2
IPQ6018# setenv serverip 192.168.1.25
IPQ6018# setenv serverip 192.168.1.10
IPQ6018#
IPQ6018# tftpboot 0x44000000 360v6op.bin&&nand erase 0x1180000 0x2ca0000&&nand write $fileaddr 0x1180000 $filesize
ipq6018_eth_halt: done
eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 up Speed :1000 Full duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
ipq6018_eth_init: done
Using eth0 device
TFTP from server 192.168.1.10; our IP address is 192.168.1.2
Filename '360v6op.bin'.
Load address: 0x44000000
Loading: T T T T T T T T T T T T T T T T T T
Got TFTP_OACK: TFTP remote port: changes from 69 to 61656
T #################################################################
         #################################################################
         #################################################################
         #################################################################
         ###################T ##############################################
         #################################################################
         #################################################################
         #################################################################
         #############################T ####################################
         #################################################################
         #################################################################
         #################################################################
         ###########################################T ######################
         #################################################################
         #################################################################
         #################################################################
         ########################################################T #########
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ###T ##############################################################
         #################################################################
         #################################################################
         #################################################################
         ################T #################################################
         #################################################################
         #################################################################
         #################################################################
         ##############################T ###################################
         #################################################################
         #################################################################
         #################################################################
         ############################################T #####################
         #################################################################
         #############################
         1.4 MiB/s
done
Bytes transferred = 33816576 (2040000 hex)
ipq6018_eth_halt: done

NAND erase: device 0 offset 0x1180000, size 0x2ca0000
Erasing at 0x3e00000 -- 100% complete.
OK

NAND write: device 0 offset 0x1180000, size 0x2040000
33816576 bytes written: OK
IPQ6018# bootipq
ubi0: attaching mtd1
UBI init error 22

Net:   MAC0 addr:0:3:7f:ba:db:ad
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (0-0)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq6018_edma_alloc_rings: successfull
ipq6018_edma_setup_ring_resources: successfull
ipq6018_edma_configure_rings: successfull
ipq6018_edma_hw_init: successfull
, eth0
IPQ6018#

lyr***

1. root@OpenWrt:~# cat /proc/mtd
   
2. dev:    size   erasesize  name
   
3. mtd0: 00180000 00020000 "0:SBL1"
   
4. mtd1: 00100000 00020000 "0:MIBIB"
   
5. mtd2: 00080000 00020000 "0:BOOTCONFIG"
   
6. mtd3: 00080000 00020000 "0:BOOTCONFIG1"
   
7. mtd4: 00380000 00020000 "0:QSEE"
   
8. mtd5: 00380000 00020000 "0:QSEE_1"
   
9. mtd6: 00080000 00020000 "0:DEVCFG"
   
10. mtd7: 00080000 00020000 "0:DEVCFG_1"
    
11. mtd8: 00080000 00020000 "0:RPM"
    
12. mtd9: 00080000 00020000 "0:RPM_1"
    
13. mtd10: 00080000 00020000 "0:CDT"
    
14. mtd11: 00080000 00020000 "0:CDT_1"
    
15. mtd12: 00080000 00020000 "0:APPSBLENV"
    
16. mtd13: 00180000 00020000 "0:APPSBL_1"
    
17. mtd14: 00180000 00020000 "0:APPSBL"
    
18. mtd15: 00080000 00020000 "0:ART"
    
19. mtd16: 05940000 00020000 "rootfs"
    
20. mtd17: 00080000 00020000 "0:ETHPHYFW"
    
21. mtd18: 00800000 00020000 "log"
    
22. mtd19: 00c00000 00020000 "plugin"
    
23. mtd20: 00080000 00020000 "config"
    
24. mtd21: 00040000 00020000 "factory"

复制代码

lyr***

U-Boot 2016.01 (Apr 29 2020 - 20:51:23 -0700)

DRAM:  smem ram ptable found: ver: 2 len: 4
512 MiB
NAND:  ONFI device found
ID = 9500a1ef
Vendor = ef
Device = a1
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC:   sdhci: Node Not found, skipping initialization

PCI0 is not defined in the device tree
In:    serial@78B1000
Out:   serial@78B1000
Err:   serial@78B1000
machid: 8030200
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
eth2 MAC Address from ART is not valid
eth3 MAC Address from ART is not valid
eth4 MAC Address from ART is not valid
eth5 MAC Address from ART is not valid
Hit any key to stop autoboot:  0
No ethernet found.
Wrong Image Format for bootm command
ERROR: can't get kernel image!

Net:   MAC0 addr:0:3:7f:ba:db:ad
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (0-0)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq6018_edma_alloc_rings: successfull
ipq6018_edma_setup_ring_resources: successfull
ipq6018_edma_configure_rings: successfull
ipq6018_edma_hw_init: successfull
eth0
IPQ6018#

a759***

我也遇到过，你重新刷uboot和大分区就可以，用以前的uboot和大分区文件就是不行，https://mbd.pub/o/bread/YpuVlJlx
然后:
mtd write /tmp/360v6-mibib.bin /dev/mtd1
mtd write /tmp/qihoo-v6-u-boot.mbn /dev/mtd13
mtd write /tmp/qihoo-v6-u-boot.mbn /dev/mtd14