求助，砖了ttl能进cfe，大神看看能救不？

fusongyan · 发表于 2017-1-11 17:45

这是ttl的信息
比对自检信息直接少了一个et0，大侠们看看能救不，ping  wan和lan都不通

SVN revision: 810
Decompressing...done

R 1.13
07DC06011801080000000000001A103F01000000

S300402B3
00002140

00000004
00000049
0000003100000031

SVN revision: 810
Decompressing...done
Found a ST compatible (Marconix) serial flash with 32 64KB blocks; total size 2MB

CFE version 6.30.163.18 (r377098) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Fri Mar  8 14:09:35 CST 2013 (tom_lin@RangeRover)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found a AMD NAND flash:
Total size:  128MB
Block size:  128KB
Page Size: 2048B
OOB Size: 64B
Sector size: 512B
Spare size:  16B
ECC level: 8-bit
Device ID: 0x01 0xf1 0x00 0x1d 0x01
DDR Clock: 533 MHz
Info: DDR frequency set from clkfreq=800,*533*
CPU type 0x0: 800MHz
Tot mem: 262144 KBytes

CFE mem: 0x00F00000 - 0x01092CA4 (1649828)
Data:    0x00F5A758 - 0x00F5AC9C (1348)
BSS:       0x00F5ACA8 - 0x00F90CA4 (221180)
Heap:    0x00F90CA4 - 0x01090CA4 (1048576)
Stack:    0x01090CA4 - 0x01092CA4 (8192)
Text:    0x00F00000 - 0x00F4F474 (324724)
Boot:    0x01093000 - 0x010D3000
Reloc:    I:00000000 - D:00000000

Board Name: WRGAC02
SVN revision: 810
[ALPHA] PRESS Ctrl-C TO ENTER EMERGENCY MODE ...
Loader:raw Filesys:tftp Dev

null) File:: Options

null)
Loading: Failed.
Could not load :: Error
Dest=00008000, source =02000000, filename=nflash1.trx
Can't open [nflash1.trx]
Loader:raw Filesys:tftp Dev

null) File:nflash0.os: Options

null)
Loading: Failed.
Could not load nflash0.os:: Network is down
CFE>

正常的ttl信息

SVN revision: 810
Decompressing...done
R 1.13
07DC06011801080000000000001A103F01000000
S300402E3
000023B0
00000004
00000050
0000003100000031
SVN revision: 810
Decompressing...done
Found a ST compatible (Marconix) serial flash with 32 64KB blocks; total size 2MB
CFE version 6.30.163.18 (r377098) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Fri Mar 8 14:09:35 CST 2013 (tom_lin@RangeRover)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found a AMD NAND flash:
Total size: 128MB
Block size: 128KB
Page Size: 2048B
OOB Size: 64B
Sector size: 512B
Spare size: 16B
ECC level: 8-bit
Device ID: 0x01 0xf1 0x00 0x1d 0x01
DDR Clock: 533 MHz
Info: DDR frequency set from clkfreq=800,*533*
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
CPU type 0x0: 800MHz
Tot mem: 262144 KBytes
CFE mem: 0x00F00000 - 0x01092CA4 (1649828)
Data: 0x00F5A758 - 0x00F5AC9C (1348)
BSS: 0x00F5ACA8 - 0x00F90CA4 (221180)
Heap: 0x00F90CA4 - 0x01090CA4 (1048576)
Stack: 0x01090CA4 - 0x01092CA4 (8192)
Text: 0x00F00000 - 0x00F4F474 (324724)
Boot: 0x01093000 - 0x010D3000
Reloc: I:00000000 - D:00000000
Board Name: WRGAC02
SVN revision: 810
We disable the arp for self.
emergency web server running ...
We disable the arp for self.
Device eth0: hwaddr 00-90-4C-0F-F0-18, ipaddr 192.168.0.1, mask 255.255.255.0
gateway not set, nameserver not set
[ALPHA] PRESS Ctrl-C TO ENTER EMERGENCY MODE ...
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: Failed.
Could not load :: Timeout occured
Dest=00008000, source =02000000, filename=nflash1.trx
[/home/tom_lin/dir868/bcm4708_ARM/src/cfe/cfe/arch/common/board/bcm947xx/src/ui_bcm947xx.c alpha_load 298] seama header magic mismatched
Loader:raw Filesys:raw Dev:nflash0.os File: Optionsnull)
Loading: .... 4144640 bytes read
Entry at 0x00008000
Closing network.
emergency web server closing ...
Starting program at 0x00008000
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
brd: module loaded
loop: module loaded
pflash: found no supported devices
Boot partition size = 262144(0x40000)
Creating 2 MTD partitions on "bcmsflash":
0x000000000000-0x000000040000 : "boot"
0x0000003f0000-0x000000400000 : "nvram"
Found a AMD NAND flash:
Total size: 128MB
Block size: 128KB
Page Size: 2048B
OOB Size: 64B
Sector size: 512B
Spare size: 16B
ECC level: 8 (8-bit)
Device ID: 0x 1 0xf1 0x 0 0x1d 0x 1 0xf1
lookup_nflash_rootfs_offset: offset = 0x0
nflash: squash filesystem with lzma found at block 13
Creating 2 MTD partitions on "nflash":
0x000000000000-0x000002000000 : "linux"
0x0000001a6dd8-0x000002000000 : "rootfs"
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
=== PPTP init ===
Mirror/redirect action on
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3990 buckets, 15960 max)
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Registering the dns_resolver key type
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD NAND 128MiB 3,3V 8-bit)
Spare area=64 eccbytes 56, ecc bytes located at:
2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63
Available 7 bytes at (off,len):
(1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0)
Scanning device for bad blocks
Options: NO_AUTOINCR,NO_READRDY,BBT_SCAN2NDPAGE,
Creating 2 MTD partitions on "brcmnand":
0x000002000000-0x000008000000 : "brcmnand"
0x000004000000-0x000008000000 : "jffs2"
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
devtmpfs: mounted
Freeing init memory: 216K
Hit ENTER for console...
emf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0x0
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.86 (r456083)
wl_module_init: passivemode set to 0x0
wl_module_init: txworkq set to 0x0
PCI: Enabling device 0001:01:00.0 (0140 -> 0142)
eth1: Broadcom BCM4331 802.11 Wireless Controller 6.37.14.86 (r456083)
eth2: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.86 (r456083)
/ # vlan1: cmd=14: Operation not supported
lo: File exists
vlan1: cmd=14: Operation not supported
vlan1: cmd=14: Operation not supported
vlan1: cmd=14: Operation not supported
vlan1: cmd=14: Operation not supported

路由摧手 · 发表于 2017-1-11 19:09

虾米机啊？

fusongyan · 发表于 2017-1-11 19:59

本帖最后由 fusongyan 于 2017-1-11 20:00 编辑

dlink的868l，坑呀，dd居然刷成砖了，tt一点事情都没有

zhjook · 发表于 2017-1-11 21:20

可以救的，你这个是固件刷错，但是cfe可以启动，电脑手动设置ip 192.168.1.100，然后开机进入cfe刷入新固件就行了，最好刷之前重置一下nvram

zhjook · 发表于 2017-1-11 21:22

你这个怎么还有个2Ｍ的　ｓｐｉ闪存啊？

fusongyan · 发表于 2017-1-11 23:45

本帖最后由 fusongyan 于 2017-1-11 23:47 编辑

是的，这个配置是flash：2+128m，内存128m，spi 2m里面有cfe，现在电脑就ping不通，明天仔细看看这个cfe支持的命令，ttl自检信息少了一条“et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)”

XteamDXF · 发表于 2017-1-12 08:48

两个F，也许是备用的启动了，默认的坏了！应该有命令开启缺少的那些，类似于安全模式，曾经在汤姆逊一体机里看到过，不过它那个备用的功能强了，自动修复默认固件

czlincy · 发表于 2018-12-15 15:09

看不懂！！！！！！！！！！！！！！！！！！！！！！！！！！！！！！！！！！！

frittb · 发表于 2018-12-28 21:50

既然能进CFE,为什么不用CFE刷呢？

账号		自动登录	找回密码
密码			立即注册

求助，砖了ttl能进cfe，大神看看能救不？

相关帖子

欢迎大家光临恩山无线论坛 /1