openwrt 刷mpr-a1 ，RT5350，启动不了系统

x56008 · 发表于 2013-11-11 11:05

最近在思考路由器的开发，自己找了一个RT5350的板子，按照openwrt的方法，编译了mpr-a1的固件，下载进去后，启动到一半后就一直提示没有设备或文件。

System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
. Image Name: MIPS OpenWrt Linux-3.10.18
Created:    2013-11-09 2:52:54 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 970408 Bytes = 947.7 kB
Load Address: 80000000
Entry Point:  80000000
raspi_read: from:50040 len:ecea8
............... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32

Starting kernel ...

[ 0.000000] Linux version 3.10.18 (huahua@Happyhua) (gcc version 4.6.4 (Open3
[ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[ 0.000000] MIPS: machine is HAME MPR-A1
[ 0.000000] Determined physical RAM map:
[ 0.000000]  memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bys
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pa8
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jff2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=0004aa90
[ 0.000000] Readback ErrCtl register=0004aa90
[ 0.000000] Memory: 29416k/32768k available (2121k kernel code, 3352k reserv)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] CPU Clock: 360MHz
[ 0.000000] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] pinctrl core: initialized pinctrl subsystem
[ 0.090000] NET: Registered protocol family 16
[ 0.110000] rt2880-pinmux pinctrl.1: invalid group "rgmii" for function "gpi"
[ 0.120000] rt2880-pinmux pinctrl.1: invalid group "mdio" for function "gpio"
[ 0.150000] bio: create slab <bio-0> at 0
[ 0.160000] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.170000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.180000] Switching to clocksource MIPS
[ 0.190000] NET: Registered protocol family 2
[ 0.200000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.220000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.230000] TCP: Hash tables configured (established 512 bind 512)
[ 0.240000] TCP: reno registered
[ 0.250000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.260000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.270000] NET: Registered protocol family 1
[ 0.280000] rt-timer 10000100.timer: maximum frequncy is 7324Hz
[ 0.330000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.340000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORI.
[ 0.370000] msgmni has been set to 57
[ 0.370000] io scheduler noop registered
[ 0.380000] io scheduler deadline registered (default)
[ 0.390000] gpio-export gpio_export.6: 2 gpio(s) exported
[ 0.410000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.420000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 1655A
[ 0.440000] console [ttyS0] enabled, bootconsole disabled
[ 0.440000] console [ttyS0] enabled, bootconsole disabled
[ 0.470000] m25p80 spi32766.0: found gd25q32, expected s25fl064k
[ 0.480000] m25p80 spi32766.0: gd25q32 (4096 Kbytes)
[ 0.490000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.500000] Creating 4 MTD partitions on "spi32766.0":
[ 0.510000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.530000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.540000] 0x000000040000-0x000000050000 : "factory"
[ 0.560000] 0x000000050000-0x000000400000 : "firmware"
[ 0.570000] 0x00000013cee8-0x000000400000 : "rootfs"
[ 0.580000] mtd: partition "rootfs" must either start or end on erase block y
[ 0.610000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.620000] mtd: partition "rootfs_data" created automatically, ofs=0x2e00000
[ 0.640000] 0x0000002e0000-0x000000400000 : "rootfs_data"
[ 0.660000] eth0: done loading
[ 0.670000] rt3xxx-usbphy ubsphy.3: loaded
[ 0.680000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.690000] TCP: cubic registered
[ 0.700000] NET: Registered protocol family 17
[ 0.710000] 8021q: 802.1Q VLAN Support v1.8
[ 0.740000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.750000] Freeing unused kernel memory: 160K (80298000 - 802c0000)
Failed to stat /dev/console
procd: Failed to stat /dev/console
Console is alive
procd: Console is alive
kmod: failed to open /proc/modules
- preinit -
procd: - preinit -
/bin/sh: can't open '/etc/preinit'
- early -
procd: - early -
- init -
procd: - init -
procd: Failed to open /proc/kmsg
procd: Failed to open /etc/inittab
open: No such file or directory
open: No such file or directory
open: No such file or directory
open: No such file or directory
open: No such file or directory
open: No such file or directory
open: No such file or directory
open: No such file or directory
open: No such file or directory
open: No such file or directory

求大能解答