|
U-Boot 1.1.3 - Modified by Manfeel (Jul 12 2014 - 16:50:29)
Board: Ralink APSoC
__ __ ______ _
| \/ | | ____| | |
| \ / | __ _ _ __ | |__ ___ ___| |
| |\/| |/ _` | '_ \| __/ _ \/ _ \ |
| | | | (_| | | | | | | __/ __/ |
|_| |_|\__,_|_| |_|_| \___|\___|_|
DRAM: 64 MB
relocate_code Pointer at: 83f64000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 30
spi device id: ef 40 18 0 0 (40180000)
find flash: W25Q128FV
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jul 12 2014 Time:16:50:29
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 500 MHZ ####
estimate memory size =64 Mbytes
MT7620 gpio init : wps / reset pin
WRTNode LED init.
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
or long press RESET/WPS button to enter web failsafe mode.
before LEDON:
data:3c7f86
You choosed 3
0
3: System Boot system code via Flash.
(Re)start USB...
USB: usb_lowlevel_init
Mediatek/Ralink USB EHCI host init hccr b01c0000 and hcor b01c0010 hc_length 16
Register 1111 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Unable to use usb 0:1 for fatload **
## Booting image at 80c00000 ...
Bad Magic Number,FFF37AFF
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-3.14.18
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1052384 Bytes = 1 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:100ee0
Verifying Checksum ... OK
Uncompressing Kernel Image ...
hdr->ih_load = 0x00000080
data pointer = 0x80c00000
first 8 bytes data = 8000006D,2EF43C00
data length = 1052384
OK
No initrd
## Transferring control to Linux (at address 80000000) ...
manfeel note, bootargs is : root=8:2 rootdelay=5 rootfstype=ext4 rw eth="00:11:22:33:44:55" console=ttyS0,115200
## Giving linux memsize in MB, 64
83f033b0:linux_argv[1] = root=8:2
83f033b9:linux_argv[2] = rootdelay=5
83f033c5:linux_argv[3] = rootfstype=ext4
83f033d5:linux_argv[4] = rw
83f033d8:linux_argv[5] = eth="00:11:22:33:44:55"
83f033f0:linux_argv[6] = console=ttyS0,115200
83f03810:linux_env[0] = memsize=64
83f0381b:linux_env[1] = initrd_start=0x00000000
83f03833:linux_env[2] = initrd_size=0x0
83f03843:linux_env[3] = flash_start=0x00000000
83f0385a:linux_env[4] = flash_size=0x1000000
Starting kernel ...
[ 0.000000] Linux version 3.14.18 (hades@PandoraBox-Server) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42788) ) #1 Mon Nov 24 19:14:47 CST 2014
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is WRTNODE
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0007e005
[ 0.000000] Readback ErrCtl register=0007e005
[ 0.000000] Memory: 61708K/65536K available (2290K kernel code, 123K rwdata, 456K rodata, 128K init, 180K bss, 3828K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 500MHz
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] genirq: Flags mismatch irq 7. 00014600 (timer) vs. 00014600 (systick)
[ 0.000000] Calibrating delay loop... 663.55 BogoMIPS (lpj=3317760)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.060000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] pinctrl core: initialized pinctrl subsystem
[ 0.070000] NET: Registered protocol family 16
[ 0.080000] bio: create slab <bio-0> at 0
[ 0.090000] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.090000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.090000] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.090000] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.100000] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.100000] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.100000] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.100000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.110000] Switched to clocksource systick
[ 0.110000] NET: Registered protocol family 2
[ 0.110000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.130000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.130000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.130000] TCP: reno registered
[ 0.130000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.150000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.150000] NET: Registered protocol family 1
[ 0.150000] rt-timer 10000100.timer: maximum frequency is 2441Hz
[ 0.170000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.190000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.190000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.210000] msgmni has been set to 120
[ 0.210000] io scheduler noop registered
[ 0.210000] io scheduler deadline registered (default)
[ 0.220000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.230000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A
[ 0.240000] console [ttyS0] enabled
[ 0.240000] console [ttyS0] enabled
[ 0.240000] bootconsole [early0] disabled
[ 0.240000] bootconsole [early0] disabled
[ 0.260000] m25p80 spi32766.0: found w25q128, expected mx25l12805d
[ 0.260000] m25p80 spi32766.0: w25q128 (16384 Kbytes)
[ 0.270000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.280000] Creating 4 MTD partitions on "spi32766.0":
[ 0.280000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.290000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.300000] 0x000000040000-0x000000050000 : "factory"
[ 0.300000] 0x000000050000-0x000001000000 : "firmware"
[ 0.310000] 0x000000150f20-0x000001000000 : "rootfs"
[ 0.320000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.330000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.340000] mtd: partition "rootfs_data" created automatically, ofs=0x310000, len=0xcf0000
[ 0.340000] 0x000000310000-0x000001000000 : "rootfs_data"
[ 0.360000] ralink_soc_eth 10100000.ethernet: Enabling TSO
[ 0.360000] ralink_soc_eth 10100000.ethernet: loaded mt7530 driver
[ 0.360000] eth0: done loading
[ 0.380000] rt3xxx-usbphy usbphy.3: loaded
[ 0.380000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.380000] TCP: cubic registered
[ 0.380000] NET: Registered protocol family 17
[ 0.400000] 8021q: 802.1Q VLAN Support v1.8
[ 0.420000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.420000] Freeing unused kernel memory: 128K (802d0000 - 802f0000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
[ 5.400000] random: mktemp urandom read with 47 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
jffs2 is not ready - marker found
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 10.950000] NET: Registered protocol family 10
[ 10.960000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.810000] rt2860v2_ap: module license 'unspecified' taints kernel.
[ 11.830000] Disabling lock debugging due to kernel taint
[ 11.880000]
[ 11.880000]
[ 11.880000] === pAd = c02ff000, size = 652464 ===
[ 11.880000]
[ 11.890000] <-- RTMPAllocTxRxRingMemory, Status=0
[ 11.900000] <-- RTMPAllocAdapterBlock, Status=0
[ 11.900000] AP Driver version-2.7.1.6
[ 11.920000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.940000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)
[ 12.020000] xt_time: kernel timezone is -0000
BusyBox v1.22.1 (2014-11-24 19:08:52 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
[ 12.060000] PPP generic driver version 2.4.2
-----------------------------------------------[ 12.060000] NET: Registered protocol family 24
------
CHAOS CALMER (Bleeding Edge, r42788)
-----------------------------------------------------
* 1 1/2 oz Gin Shake with a glassful
* 1/4 oz Triple Sec of broken ice and pour
* 3/4 oz Lime Juice unstrained into a goblet.
* 1 1/2 oz Orange Juice
* 1 tsp. Grenadine Syrup
-----------------------------------------------------
root@(none):/# [ 13.570000] RX DESC a2d55000 size = 2048
[ 13.570000] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801a1184, ra == 82caeee8
[ 13.590000] Oops[#1]:
[ 13.590000] CPU: 0 PID: 506 Comm: ifconfig Tainted: P 3.14.18 #1
[ 13.590000] task: 83871c20 ti: 83b84000 task.ti: 83b84000
[ 13.590000] $ 0 : 00000000 00000000 00000000 00000f00
[ 13.590000] $ 4 : 00000000 00000f00 00000f00 00000002
[ 13.590000] $ 8 : 00000024 80008bec 35356432 20303030
[ 13.590000] $12 : 00000000 778b23a0 00000000 00000151
[ 13.590000] $16 : 00000001 82003920 c0302ad8 c0302ad4
[ 13.590000] $20 : 83bc2000 a0000000 00000f00 82d40000
[ 13.590000] $24 : 00000000 801a10d8
[ 13.590000] $28 : 83b84000 83b85c28 a31ed400 82caeee8
[ 13.590000] Hi : 00000000
[ 13.590000] Lo : c74d8000
[ 13.590000] epc : 801a1184 r4k_dma_cache_inv+0xac/0xc8
[ 13.590000] Tainted: P
[ 13.590000] ra : 82caeee8 linux_pci_map_single+0x68/0x94 [rt2860v2_ap]
[ 13.590000] Status: 1100e403 KERNEL EXL IE
[ 13.590000] Cause : 00800008
[ 13.590000] BadVA : 00000000
[ 13.590000] PrId : 00019650 (MIPS 24KEc)
[ 13.590000] Modules linked in: pppoe ppp_async iptable_nat pppox ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 ipt_MASQUERADE xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT slhc nf_nat_irc nf_nat_ftp nf_nat nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_irc nf_conntrack_ftp nf_conntrack iptable_raw iptable_mangle iptable_filter ipt_REJECT ip_tables crc_ccitt rt2860v2_ap(P) ralink_eeprom_api ip6t_REJECT ip6table_raw ip6table_mangle ip6table_filter ip6_tables x_tables ipv6 leds_gpio gpio_button_hotplug
[ 13.590000] Process ifconfig (pid: 506, threadinfo=83b84000, task=83871c20, tls=77939440)
[ 13.590000] Stack : c0302ad4 839e8720 00001000 00000000 c0302ad4 82caeee8 c02ff000 c0302ad8
60000000 c03019ec c02ff000 83a92b40 00000f00 82caefa8 a31ed400 80225004
000004d4 802c03e8 0000ff01 c033c928 c02ff000 c0302ad8 02d55000 c0303ad8
00000010 82c417e8 c033c928 a2d55000 00000800 00000001 c0302ad4 c0302ad8
c02ff000 82d40000 00000001 00000000 00000000 82d30ea0 00008914 7fe4a168
...
[ 13.590000] Call Trace:
[ 13.590000] [<801a1184>] r4k_dma_cache_inv+0xac/0xc8
[ 13.590000] [<82caeee8>] linux_pci_map_single+0x68/0x94 [rt2860v2_ap]
[ 13.590000] [<82caefa8>] RTMP_AllocateRxPacketBuffer+0x94/0xbc [rt2860v2_ap]
[ 13.590000] [<82c417e8>] RTMPInitTxRxRingMemory+0x230/0x3a4 [rt2860v2_ap]
[ 13.590000] [<82c1b3a0>] rt28xx_init+0x180/0x1a74 [rt2860v2_ap]
[ 13.590000] [<82cacd58>] rt28xx_open+0xa0/0x108 [rt2860v2_ap]
[ 13.590000] [<82c2a2b0>] RTMP_COM_IoctlHandle+0x3f4/0x8f0 [rt2860v2_ap]
[ 13.590000] [<82cac648>] MainVirtualIF_open+0x7c/0x12c [rt2860v2_ap]
[ 13.590000] [<8002f560>] __dev_open+0xe0/0x148
[ 13.590000] [<8002eea8>] __dev_change_flags+0xb8/0x17c
[ 13.590000] [<800a3c5c>] dev_change_flags+0x28/0x70
[ 13.590000] [<800ab75c>] devinet_ioctl+0x5fc/0x664
[ 13.590000] [<801dc230>] sock_ioctl+0x2a4/0x300
[ 13.590000] [<800c3128>] do_vfs_ioctl+0x490/0x588
[ 13.590000] [<80017a44>] SyS_ioctl+0x50/0x94
[ 13.590000] [<8000683c>] handle_sys+0x11c/0x140
[ 13.590000]
[ 13.590000]
Code: 2484ffff 00852821 00a31824 <bc510000> 1443fffe 24420020 0000000f 8fbf0014 03e00008
[ 13.880000] ---[ end trace 898f26c7d8f89bcc ]---
请不要胡乱输入以及粘贴、复制等方式灌水
请尊重作者、并共同维护网站的正常阅读,否则账户将会被限制发帖、回帖,并且积分可能会被清零,站内短信以及阅读权限等都会受到影响,谢谢。
具体限制方式:https://www.right.com.cn/forum/thread-8307840-1-1.html
|
|