求教有没有乐光 LG-A200的胖AP固件？

on***

弄了一个LG-A200吸顶式无线AP，但是是瘦AP，需要AC控制器才能用，我想把这个瘦AP刷成胖AP，不知道哪位大侠有这个AP的刷机固件？能提供一下下载吗？谢谢






找到了两个固件，但是不知道怎么刷机，板子上有ttl接口，用2303刷机线连接上，在secureCRT软件上也显示了开机信息，可惜无法中断下来，启动到最后也进不去shell命令行，根本就没有shell
开机前插入刷机线，开机会卡在下面信息，然后就一直卡在那里，没有任何代码显示了，敲回车键也没反应，ap的指示灯也不闪烁，说明没启动起来，卡在这里好几分钟都没任何反应
U-Boot 1.1.4-dirty (Dec  6 2016 - 02:58:15)

ap147 - Honey Bee 2.0DRAM:  
sri
Honey Bee 2.0
ath_ddr_initial_config(219): (16bit) ddr1 init
QiLun uboot. TEL:13430494701
tap = 0x00000000
Tap (low, high) = (0x8, 0x3a)
Tap values = (0x21, 0x21, 0x21, 0x21)
4 MB
Top of RAM usable for U-Boot at: 80400000
Reserving 199k for U-Boot at: 803cc000
Reserving 192k for malloc() at: 8039c000
Reserving 44 Bytes for Board Info at: 8039bfd4
Reserving 36 Bytes for Global Data at: 8039bfb0
Reserving 128k for boot params() at: 8037bfb0
Stack Pointer at: 8037bf98

第二次试验，上电开机15秒以后，插上刷机线，就不会卡在上面那里，后面的信息会继续显示，也就是说ap继续启动运行系统了，虽然跳出了press enter to activate this console，但是狂按回车键毫无反应，试验多次都停不下来，也就是说按键根本无效，根本进不了console控制台，15秒之前插入刷机线会卡在上面代码，之后插入会全部启动完，直至指示灯闪烁，IE可以连接后台管理，如上面最后两幅图片，后台管理里边没有升级固件的选项，各位，这个瘦AP还能怎么玩？


Please press Enter to activate this console. [   19.980000] usbcore: registered new interface driver usbfs
[   19.980000] usbcore: registered new interface driver hub
[   19.990000] usbcore: registered new device driver usb
[   20.010000] Button Hotplug driver version 0.4.1
[   20.090000] asf: module license 'Proprietary' taints kernel.
[   20.100000] Disabling lock debugging due to kernel taint
[   20.110000] ****Address of trace_timer :870d2630
[   20.440000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)
[   20.530000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
[   20.550000] ath_dfs: Version 2.0.0
[   20.550000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
[   20.570000] ath_spectral: Version 2.0.0
[   20.570000] Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved
[   20.590000] SPECTRAL module built on May  8 2017 06:41:23
[   20.660000] ath_tx99: Version 2.0
[   20.660000] Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved
[   20.850000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
[   23.000000] __ath_attach: Set global_scn[0]
[   23.000000] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
[   23.010000] ACBKMinfree = 48
[   23.010000] ACBEMinfree = 32
[   23.020000] ACVIMinfree = 16
[   23.020000] ACVOMinfree = 0
[   23.020000] CABMinfree = 48
[   23.030000] UAPSDMinfree = 0
[   23.030000] ATH_TXBUF=540
[   23.040000] Enterprise mode: 0x03fc0000
[   23.040000] Restoring Cal data from DRAM
[   23.050000]
[   23.050000] ART Version : -48
[   23.050000] SW Image Version : 54.10.0.1554.149
[   23.060000] Board Revision : 7
[   23.060000] ar9300_attach: nf_2_nom -110 nf_2_max -60 nf_2_min -125
[   23.070000] SPECTRAL : get_capability not registered
[   23.070000] HAL_CAP_PHYDIAG : Capable
[   23.080000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231)
[   23.090000] SPECTRAL : get_capability not registered
[   23.090000] HAL_CAP_RADAR   : Capable
[   23.100000] SPECTRAL : Need to fix the capablity check for SPECTRAL
[   23.100000]  (spectral_attach : 236)
[   23.110000] SPECTRAL : get_capability not registered
[   23.110000] HAL_CAP_SPECTRAL_SCAN : Capable
[   23.120000] SPECTRAL : get_tsf64 not registered
[   23.120000] spectral_init_netlink 63 NULL SKB
[   23.120000] SPECTRAL : No ADVANCED SPECTRAL SUPPORT
[   23.130000] SPECTRAL :----- module attached
[   23.130000] Green-AP : Green-AP : Attached
[   23.130000]
[   23.140000] ath_get_caps[6191] rx chainmask mismatch actual 1 sc_chainmak 0
[   23.150000] ath_get_caps[6166] tx chainmask mismatch actual 1 sc_chainmak 0
[   23.160000] band steering initialized for direct attach hardware
[   23.170000] ieee80211_bsteering_attach: Band steering initialized
[   23.180000] ath_attach_dfs[12711] dfsdomain 1
[   23.190000] SPECTRAL : module already attached
[   23.200000] ugw_init_netlink success.
[   23.200000] ntc_sta_buffer_init: pre-alloacting memmory for stas is succeed in g_sta_2g_premem.
[   23.210000] osif_wrap_attach:295 osif wrap attached
[   23.210000] osif_wrap_devt_init:915 osif wrap dev table init done
[   23.220000] ath_tx_paprd_init sc 872c0000 PAPRD disabled in HAL
[   23.230000] wifi0: Atheros ???: mem=0xb8100000, irq=47
[   23.240000] ath_pci: SmartAntenna-DRT-0.1 (Atheros/multi-bss)
[   23.240000] ath_pci_probe
[   23.250000] PCI device id is 0050 :0050
[   23.250000] ath_pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[   23.260000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   23.270000] ath_pci 0000:00:00.0: ath DEBUG: sc=0x86509000
[   23.270000]
[   23.270000]  ol_ath_pci_configure : num_desired MSI set to 0
[   23.280000]
[   23.280000]  Using PCI Legacy Interrupt
[   24.290000] CE_per_engine_handler_adjust, base=86509000 offset=57400
[   24.290000] CE_per_engine_handler_adjust, base=86509000 offset=57800
[   24.310000] __ol_ath_attach: ath_attach TODO
[   24.310000] __ol_ath_attach: dev name wifi1
[   24.320000] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko)
[   24.330000]  OL_ACBKMinfree : 0
[   24.330000]  OL_ACBEMinfree : 0
[   24.330000]  OL_ACVIMinfree : 0
[   24.340000]  OL_ACVOMinfree : 0
[   24.340000] ol_ath_attach() BMI inited.
[   24.350000] ol_ath_attach() BMI Get Target Info.
[   24.350000] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016d
[   24.360000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
[   24.360000] ol_ath_attach() configure Target .
[   24.370000] ol_ath_download_firmware: Using caldata from Target EEPROM for AR9887
[   24.700000] ugw_read_cal_5g-1861: *** qilun  CAL READ FILE!
[   24.700000] qc98xx_verify_checksum: flash checksum passed: 0x3736
[   24.710000] ol_transfer_target_eeprom_caldata 1946: Download Target EEPROM caldata len 2116
[   24.720000] Swift firmware download
[   24.730000] ol_transfer_bin_file 2173: Download Firmware data len 217896
[   25.660000] ol_ath_attach() Download FW.
[   25.660000] ol_ath_attach() HT Create .
[   25.670000] ol_ath_attach() HIF Claim.
[   25.670000] ol_ath_attach() BMI Done.
[   25.670000] ol_ath_attach() WMI attached. wmi_handle 873b0000
[   25.680000] +HWT
[   25.680000] SOC_RESET_CONTROL_ADDRESS : 800
[   25.690000] CPU_INTR_ADDRESS = [2000000]
[   25.690000] SOC_GLOBAL_RESET_ADDRESS = [0]
[   25.690000] Rx_Filter : [0]
[   25.700000] CE_per_engine_handler_adjust, base=86509000 offset=57400
[   25.700000] CE_per_engine_handler_adjust, base=86509000 offset=57800
[   25.710000] CE_per_engine_handler_adjust, base=86509000 offset=57c00
[   25.720000] CE_per_engine_handler_adjust, base=86509000 offset=58000
[   25.720000] CE_per_engine_handler_adjust, base=86509000 offset=58400
[   25.730000] CE_per_engine_handler_adjust, base=86509000 offset=58800
[   25.740000] CE_recv_buf_enqueue 653 Populate last entry 512 for CE 5
[   25.750000] CE_recv_buf_enqueue 662 CE 5 wi 511 dest_ptr 0x5d96020 nbytes 0 recv_ctxt 0x863fc9c0
[   25.760000] Target:87966800 HTC Service:0x0001, ULpipe:0 DLpipe:1 id:0 Ready
[   25.770000] -HWT
[   25.770000] Target:87966800 HTC Service:0x0300, ULpipe:4 DLpipe:5 id:1 Ready
[   25.780000] HTC Service:0x0300 ep:1 TX flow control disabled
[   25.790000] CE_pkt_dl_len_set CE 4 Pkt download length 64
[   25.790000] ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from 859d0000
[   25.800000] Target:87966800 HTC Service:0x0100, ULpipe:3 DLpipe:2 id:2 Ready
[   25.810000] HTC Service:0x0100 ep:2 TX flow control disabled
[   25.820000] wmi_service_ready_event_rx:  WMI UNIFIED SERVICE READY event
[   25.820000] num_rf_chain : 00000001
[   25.830000] ht_cap_info: : 0000085b
[   25.830000] vht_cap_info : 338001b2
[   25.830000] vht_supp_mcs : 0000fffe
[   25.840000] LARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256, lteu_support 0
[   25.850000] idx 0 req 1  num_units 0 num_unit_info 2 unit size 404 actual units 145
[   25.850000] chunk 0 len 58580 requested ,ptr  0x59f0000
[   25.870000] FIRMWARE 145 V 16 T 443
[   25.870000]  
[   25.870000] wmi_ready_event_rx:  WMI UNIFIED READY event
[   25.880000] ol_ath_connect_htc() WMI is ready
[   25.880000] ol_ath_set_host_app_area TODO
[   25.890000] target uses HTT version 2.1; host uses 2.1
[   25.900000] ol_ath_attach() connect HTC.
[   25.900000] bypasswmi : 0
[   25.900000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
[   25.920000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
[   25.920000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
[   25.930000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
[   25.940000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
[   25.950000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
[   25.950000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
[   25.960000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
[   25.970000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
[   25.980000] Add VHT80 channel: 5210
[   25.980000] Add VHT80 channel: 5290
[   25.980000] Add VHT80 channel: 5530
[   25.990000] Add VHT80 channel: 5610
[   25.990000] Add VHT80 channel: 5690
[   25.990000] Add VHT80 channel: 5775
[   26.000000] Skipping VHT80 channel 5825
[   26.000000] ol_ath_phyerr_attach: called
[   26.010000] OL Resmgr Init-ed
[   26.010000] ieee80211_bsteering_attach: Band steering initialized
[   26.020000] ol_if_spectral_setup
[   26.020000] SPECTRAL : get_capability not registered
[   26.020000] HAL_CAP_PHYDIAG : Capable
[   26.030000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231)
[   26.040000] SPECTRAL : get_capability not registered
[   26.040000] HAL_CAP_RADAR   : Capable
[   26.050000] SPECTRAL : Need to fix the capablity check for SPECTRAL
[   26.050000]  (spectral_attach : 236)
[   26.060000] SPECTRAL : get_capability not registered
[   26.060000] HAL_CAP_SPECTRAL_SCAN : Capable
[   26.070000] SPECTRAL : get_tsf64 not registered
[   26.070000] spectral_init_netlink 63 NULL SKB
[   26.070000] Green-AP : Green-AP : Attached
[   26.070000]
[   26.080000] Green-AP : Attached
[   26.080000] ol_if_dfs_setup: called
[   26.090000] ol_if_dfs_attach: called; ptr=859cd974, radar_info=8709db78
[   26.100000] ol_ath_rtt_meas_report_attach: called
[   26.100000] ol_ath_attach() UMAC attach .
[   26.110000] ol_if_dfs_configure: called
[   26.110000] ol_if_dfs_configure: FCC domain
[   26.110000] ol_if_dfs_disable: called
[   26.120000] ol_ath_attach: Calling ol_if_dfs_configure
[   26.120000] ugw_init_netlink success.
[   26.130000] ntc_sta_buffer_init: pre-alloacting memmory for stas is succeed in g_sta_5g_premem.
[   26.140000] osif_wrap_attach:295 osif wrap attached
[   26.140000] osif_wrap_devt_init:915 osif wrap dev table init done
[   26.150000] __ol_ath_attach: init tx/rx TODO
[   26.150000] __ol_ath_attach: hard_header_len reservation 58
[   26.170000] Initializing Pktlogs for 11ac
[   26.190000] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[   26.300000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   26.390000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   26.400000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller
[   26.410000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[   26.450000] ehci-platform ehci-platform.0: irq 3, io mem 0x1b000000
[   26.470000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[   26.470000] hub 1-0:1.0: USB hub found
[   26.480000] hub 1-0:1.0: 1 port detected
[   26.490000] nf_conntrack version 0.5.0 (1978 buckets, 7912 max)
[   26.670000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   26.680000] [wifi1] FWLOG: [39440] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x460, 0x460, 0x0 )
[   26.690000] [wifi1] FWLOG: [39440] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x460, 0x460, 0x0 )
[   26.700000] [w

5232***

什么硬件你贴出来啊，说不定同配置的可以试试

happych***

9531+9887  

on***

happychina2008 发表于 2019-12-5 14:28
9531+9887

谢谢，因为CPU贴着散热器，所以也没拆下来看过，上面确实有一个9887的芯片，不知道能不能刷爱快H3固件，有没有胖AP固件？

on***

集客AP260F-H是不是和我这个一样的？

on***

谁有编程器固件？怎么把下载的openwrt固件用编程器刷进去？

on***

刷superwrt固件可以，不过专业版是收费的，普通版就相当于普通路由器

百万如***

还需要么 我刚刚好有个A200