求助 水星mw300m v4 无有线无无线信号，ttl信息如下，修好送红包

陆不败

请高手看一下，从朋友那儿拿了个坏了的水星mw300m v4   ar9431 主控， 2m闪存  16m内存，
自己焊了TTL 口，插网线1，3口 wan口显示断开，用万用表量 这几个口的电阻断开，看外观是烧了
2,4网口插线显示未识别的网络，无论是自动还是手动分配ip都一样，
另外没有无线发射，  复位依旧，系统灯常闪，
ttl 波特率设115200，
如下信息
请高手帮忙查一查问题，
如修复送微信红包


         ________  ________             __      __  ____   _  __   ___
        |________||   ___  |           |  |    |  ||    \ | ||  | /  /
           |  |   |  |___| |   __ __   |  |    |  ||     \| ||  |/  /
           |  |   |   _____|  |__ __|  |  |___ |  || |\     ||      \
           |__|   |__|                 |______||__||_| \____||__|\___\


                            Software Platform for MIPS
Creation date: Jul  5 2011, 09:13:06 (huangqingjia@tp-link.net)
Copyright(C) 2001-2012 by TP-LINK TECHNOLOGIES CO., LTD.
CPU: AR9341: AP123 Board
CPU freq: 500 MHZ
SDRAM size: 16 MB
ipaddr:192.168.1.1
serverip:192.168.1.100
file:vxWorks.img


Press Ctrl+C to stop auto-boot...
0
auto-booting...
Uncompressing...done
Starting at 0x80001000...

Attaching interface lo0... done
Rx clbufs 512 each of size 1756
eth_rx_netpool_init: allocated, pDmaBuf=0x80e4e3e0, buffend = 80f2abe4
ATHRS27: resetting s27
ATHRS27: s27 reset done
eth_rx_netpool_init: done already!
interrupt: enet1 port1 up
interrupt: LAN Port Interface type is 0x4c04
interrupt: enet1 port2 up
interrupt: LAN Port Interface type is 0x4c04
Attached IPv4 interface to mirror unit 0
usrAppInitEx: 112: GPIO_OE = 30300
usrAppInitEx: 113: CP0 CONFIG = 80208483
usrAppInitEx: 114: CP0 CONFIG1 = bee3519e

-->starting wireless...
APCFG task id 80c7d450
sysWlanInit ...
Create WLAN event task tWLANEventTask
Create mem partion 0x80c69c20 for size 28672
AH_CAL_IN_FLASH_AHB
Boostrap clock 25MHz
ar9300RadioAttach: Need analog access recipe!!
Restoring Cal data from Flash
ath_get_caps[4703] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[4678] tx chainmask mismatch actual 3 sc_chainmak 0
Create OS_MESGQ Successfully at 0x80c58630
osifp->queue_head = 0x80c58930
ag7240MemInit: allocated, dmabuf=0x80ba3c10, buffend = 80c4be14
Entering Task Loop
Entering WLAN event Task Loop
interrupt: enet0 port4 up
interrupt: enet0 port4 down
ERROR:wireless OR ACL disable
sending message 80b7f3e0,24
sending message 80b7f3e0,24
TDDP: Now listening client request.
tddp is running.
httpInit: System File Registry successfully initialized.
httpInit: System File Manager successfully initialized.
httpInit: File System RPM successfully initialized.
httpInit: RPM dispatcher successfully initialized.
httpInit: MIME type guessing RPM successfully initialized.
httpInit: http Password Checking successfully initialized.
httpInit: http Access Control successfully initialized.



                            Software Platform for MIPS
  Copyright(C) 2001-2010 by TP-LINK TECHNOLOGIES CO., LTD.
Starting  Creation date:  WLJul  5 2011, 10:13:42AN !!!!

# AP_STARTMODE=standard
AP_ENABLE=1
ATH_COUNTRYCODE=156

Co-processor unusable Exception
Exception Program Counter: 0x801a8094
Status Register: 0x0000f401
Cause Register: 0x2000002c
Task: 0x80c7d450 "tAPCfg"
interrupt: enet0 port4 up
interrupt: enet0 port4 down
interrupt: enet0 port4 up
interrupt: enet1 port1 down
interrupt: enet1 port2 down
interrupt: enet0 port4 down
interrupt: enet1 port1 up
interrupt: LAN Port Interface type is 0x4c04
interrupt: enet1 port2 up
interrupt: LAN Port Interface type is 0x4c04
interrupt: enet0 port4 up
interrupt: enet0 port4 down
interrupt: enet0 port4 up
interrupt: enet0 port4 down
interrupt: enet0 port4 up
interrupt: enet0 port4 down
interrupt: enet0 port4 up