求教华硕WL-500G如何刷DDWRT？

TOPCOOL

从来没刷过DDWRT，很想试试，只知道手上的500G支持，但是就是不知道怎么刷成DDWRT，希望各位大虾能帮帮忙。
另外我看到有什么MINI版、标准版和vint版，不知道他们有什么区别？谢谢各位了。在线等哈，最好有中文详细教程，怕变砖啊。

望雨思幽

刷S版起始就可以 。。直接刷就成吧？
只要不刷错华硕有恢复模式的 通电前俺 RESET 看电源灯是不是来回闪就行
如果可以就随便刷了

prooo

dd的官网上有教程的呀，具体怎么刷太久了忘了。

cg198298

我刷了的，用起来很不错，但是是很久以前的事了，反正是刷了2个文件才刷好的，用的华硕的工具刷的
[edit] Asus WL500G (Original)
You will need:

A PC directly connect to one of the LAN ports of the router, via ethernet cable. (Unfortunately, it has to be a Windows based PC. I was unable to upload the firmware via tftp command. Maybe you'll have better luck with Linux). Note: Manually disable all installed NICs except the one you will use to connect to the router.
These two files: wl500g-clear-nvram.trx (filesize: 1,585,152 bytes) and wl500g-recover.trx (filesize: 3,690,496 bytes)
Asus Firmware Restoration Tool. This is found on the CD that comes with the router OR Asus Support website here. Its hidden in Utilities section and named Asus WL-500b/g wireless router utility program in English. Version 1.3.8.0 (for the English version). The file is called Eng_1380.zip (Use unzip app to decompress).
DD-WRT v23 SP2
This procedure was developed using the Mitsubishi R100 router with the standard variant of DD-WRT. It should be identical with the Asus WL500G (Original)

This process requires a bit of patience and persistance. The WL500G and the relabeled R100 are stubborn routers that need a bit of encouragement. Eventually, you will be successful with installing DD-WRT onto them.

Set the PC to have a static IP address of 192.168.1.10, while the gateway entry is 192.168.1.1

Before you plug the power connector in, press and hold the Restore or Reset button on the back.

While holding the reset button, plug the power connector in.

This causes it to go into Restore mode. This is indicated by the PWR LED flashing at regular intervals.

Now use the Asus Firmware Restoration Tool and upload wl500g-clear-nvram.trx. Wait until upload is complete and it reboots. This is usually takes about 2 to 3 minutes.

Once done, unplug the power connector. Wait for 30 seconds or so.

Repeat steps 2 to 6, but upload wl500g-recover.trx instead.

Now plug the power connector back into the router.

Try to ping the router from your PC. If it responds, then you are ready to upload DD-WRT firmware. Proceed to step 9.

If not, then repeat steps 2 to 7 until it does.

If that fails, set the router in Restore mode (as mentioned in step 2 to 4), but install DD-WRT firmware. Then wipe it off by repeating steps 2 to 8. You must have it such that the router MUST respond to ping in Restore mode!

Install DD-WRT v23 SP2 Asus firmware using the Asus Firmware Restoration Tool. (The firmware file is called dd-wrt.v23_asus.trx).

Once done, wait for a few minutes until it reboots. This can be seen by the AIR LED flashing at regular periods.

Now try pinging the router with DD-WRT firmware installed.
If it responds, continue to step 12.

If it does NOT respond to pings, repeat steps 2 to 11. Repeat until it responds with DD-WRT installed.

Login in via web browser by entering http://192.168.1.1/ and the default login is root, with the password admin

Enjoy your R100 or WL500G with DD-WRT v23 SP2!
只找到这个，你参考看看把

cg198298

晕看不到连接，那就看这个WORD的

wangdeng

用Asus的Firmware Restoration
按住Restore不放，插入电源，在power灯开始闪烁时松开restore按钮。
这时候打开Firmware Restoration，浏览，找到下载的dd-wrt固件
按上传，这时就会开始上传固件到路由器
注意使用网线连接路由器与电脑并为电脑指定一个IP

TOPCOOL

感谢楼上走过路过留下脚印的高手们，我先试试刷个stand版本，成功了再来求教，谢谢各位！

lpyw98

向优秀的同仁们思考了

alikexie

找华硕的刷机工具，不要进页面刷，很方便安全。