TTL有显示，不知对不对，就是无法刷机？

zyzjh88

nf_conntrack version 0.5.0 (3955 buckets, 15820 max)
NETDETECT target register
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
ip_nat_bnet: Trying to register for port 6112
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
TCP cubic registered
Twin IP Module Init
--> Init Smart QoS Monitor
Init SKIP Netfilter
NET: Registered protocol family 17
L2TP core driver, V2.0
L2TP netlink interface
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
List of all partitions:
1f00           16128 mtdblock0 (driver?)
1f01             128 mtdblock1 (driver?)
1f02              64 mtdblock2 (driver?)
1f03              64 mtdblock3 (driver?)
1f04            2176 mtdblock4 (driver?)
1f05           13952 mtdblock5 (driver?)
No filesystem could mount root, tried:  ext3 ext2 ext4 squashfs vfat fuseblk
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5)

===================================================================
                MT7621   stage1 code 10:33:55 (ASIC)
                CPU=500000000 HZ BUS=166666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL4 FB_DL: 0x9, 1/0 = 646/378 25000000
PLL2 FB_DL: 0xd, 1/0 = 558/466 35000000
PLL3 FB_DL: 0x10, 1/0 = 673/351 41000000
do DDR setting..[01F40000]
Apply DDR3 Setting...(use customer AC)
          0    8   16   24   32   40   48   56   64   72   80   88   96  104  112  120
      --------------------------------------------------------------------------------
0000:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0001:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0002:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0003:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0004:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0005:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0006:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0007:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0008:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0009:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    1
000E:|    0    0    0    0    0    0    0    0    0    1    1    1    1    1    1    1
000F:|    0    0    0    0    1    1    1    1    1    1    1    1    1    1    0    0
0010:|    1    1    1    1    1    1    1    1    1    0    0    0    0    0    0    0
0011:|    1    1    1    1    0    0    0    0    0    0    0    0    0    0    0    0
0012:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0013:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0014:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0015:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0016:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0017:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0018:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0019:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001E:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001F:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
rank 0 coarse = 15
rank 0 fine = 72
B:|    0    0    0    0    0    0    0    0    1    1    1    0    0    0    0    0
opt_dle value:9
DRAMC_R0DELDLY[018]=00001E1F
==================================================================
                RX      DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit|     0  1  2  3  4  5  6  7  8  9
--------------------------------------
0 |    11 9 9 10 9 9 9 7 6 8
10 |    7 11 9 10 6 10
--------------------------------------

==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delayQS0 =31 DQS1 = 30
==================================================================
bit     DQS0     bit      DQS1
0  (1~59)30  8  (0~58)29
1  (1~58)29  9  (1~58)29
2  (1~58)29  10  (1~59)30
3  (1~58)29  11  (1~59)30
4  (1~59)30  12  (1~60)30
5  (1~61)31  13  (1~58)29
6  (1~60)30  14  (1~59)30
7  (1~62)31  15  (1~60)30
==================================================================
3.dq delay value last
==================================================================
bit|    0  1  2  3  4  5  6  7  8   9
--------------------------------------
0 |    12 11 11 12 10 9 10 7 7 9
10 |    7 11 9 11 6 10
==================================================================
==================================================================
     TX  perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15,  finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15,  finish count=2
DQ loop=15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=15,  finish count=1
dqs_perbyte_dly.last_dqdly_pass[1]=15,  finish count=2
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
20,data:88
[EMI] DRAMC calibration passed

===================================================================
                MT7621   stage1 code done
                CPU=500000000 HZ BUS=166666666 HZ
===================================================================


U-Boot 1.1.3 (Aug 31 2015 - 22:21:15)

Board: Ralink APSoC DRAM:  256 MB
relocate_code Pointer at: 8ffb8000

Config XHCI 40M PLL
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:Aug 31 2015  Time:22:21:15
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
#Reset_MT7530

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   6: Load Flash code then burn to Flash via TFTP.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.

You choosed 3

0
   
3: System Boot system code via Flash.
## Booting image at bfc50000 ...
   Image Name:   za3nd
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    11558848 Bytes = 11 MB
   Load Address: 80001000
   Entry Point:  8000f500
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000f500) ...
## Giving linux memsize in MB, 256

Starting kernel ...


LINUX started...

THIS IS ASIC
Linux version 2.6.36 (mt7621@ski) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #111 SMP Mon Nov 23 17:27:03 KST 2015

The CPU feqenuce set to 880 MHz
GCMP present
CPU revision is: 0001992f (MIPS 1004Kc)
Software DMA cache coherency
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00010000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00010000
Detected 3 available secondary CPU(s)
PERCPU: Embedded 7 pages/cpu @81203000 s6912 r8192 d13568 u65536
pcpu-alloc: s6912 r8192 d13568 u65536 alloc=16*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 console=ttyS0
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Writing ErrCtl register=0004021f
Readback ErrCtl register=0004021f
Memory: 253168k/262144k available (4662k kernel code, 8976k reserved, 1367k data, 216k init, 0k highmem)
Hierarchical RCU implementation.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:128
Trying to install interrupt handler for IRQ24
Trying to install interrupt handler for IRQ25
Trying to install interrupt handler for IRQ22
Trying to install interrupt handler for IRQ9
Trying to install interrupt handler for IRQ10
Trying to install interrupt handler for IRQ11
Trying to install interrupt handler for IRQ12
Trying to install interrupt handler for IRQ13
Trying to install interrupt handler for IRQ14
Trying to install interrupt handler for IRQ16
Trying to install interrupt handler for IRQ17
Trying to install interrupt handler for IRQ18
Trying to install interrupt handler for IRQ19
Trying to install interrupt handler for IRQ20
Trying to install interrupt handler for IRQ21
Trying to install interrupt handler for IRQ23
Trying to install interrupt handler for IRQ26
Trying to install interrupt handler for IRQ27
Trying to install interrupt handler for IRQ28
Trying to install interrupt handler for IRQ15
Trying to install interrupt handler for IRQ8
Trying to install interrupt handler for IRQ29
Trying to install interrupt handler for IRQ30
Trying to install interrupt handler for IRQ31
console [ttyS1] enabled
Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
launch: starting cpu1
launch: cpu1 gone!
CPU revision is: 0001992f (MIPS 1004Kc)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
launch: starting cpu2
launch: cpu2 gone!
CPU revision is: 0001992f (MIPS 1004Kc)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
launch: starting cpu3
launch: cpu3 gone!
CPU revision is: 0001992f (MIPS 1004Kc)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Brought up 4 CPUs
Synchronize counters across 4 CPUs: done.
NET: Registered protocol family 16
release PCIe RST: RALINK_RSTCTRL = 7000000
PCIE PHY initialize
***** Xtal 40MHz *****
start MT7621 PCIe register access
RALINK_RSTCTRL = 7000000
RALINK_CLKCFG1 = 77ffeff8

*************** MT7621 PCIe RC mode *************
PCIE2 no card, disable it(RST&CLK)
pcie_link status = 0x3
RALINK_RSTCTRL= 3000000
*** Configure Device number setting of Virtual PCI-PCI bridge ***
RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
PCIE0 enabled
PCIE1 enabled
interrupt enable status: 300000
Port 1 N_FTS = 1b105000
Port 0 N_FTS = 1b105000
config reg done
init_rt2880pci done
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x60400000-0x6040ffff] (PCI address [0x60400000-0x6040ffff]
pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
pci 0000:00:01.0: BAR 1: set to [mem 0x60410000-0x6041ffff] (PCI address [0x60410000-0x6041ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x600fffff 64bit] (PCI address [0x60000000-0x600fffff]
pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
pci 0000:02:00.0: BAR 0: set to [mem 0x60200000-0x602fffff 64bit] (PCI address [0x60200000-0x602fffff]
pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
pci 0000:00:01.0: PCI bridge to [bus 02-02]
pci 0000:00:01.0:   bridge window [io  disabled]
pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 60400000
res[1]->end = 6040ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
BAR0 at slot 1 = 0
bus=0x0, slot = 0x1
res[0]->start = 0
res[0]->end = 0
res[1]->start = 60410000
res[1]->end = 6041ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0, irq=0x4
res[0]->start = 60000000
res[0]->end = 600fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x2, slot = 0x1, irq=0x18
res[0]->start = 60200000
res[0]->end = 602fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource MIPS
NET: Registered protocol family 2
-->  ipconflict proc OK !!!!!!!!!!
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
4 CPUs re-calibrate udelay(lpj = 1167360)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.15)
msgmni has been set to 494
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Ralink gpio driver initialized
spidrv_major = 217
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
brd: module loaded
flash manufacture id: ef, device id 40 18
W25Q128BV(ef 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 6 MTD partitions on "raspi":
0x000000040000-0x000001000000 : "Firmware"
0x000000000000-0x000000020000 : "Bootloader"
0x000000020000-0x000000030000 : "Config"
0x000000030000-0x000000040000 : "Factory"
0x000000040000-0x000000260000 : "Kernel"
0x000000260000-0x000001000000 : "RootFS"
rdm_major = 253
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x432880ed
Ralink APSoC Ethernet Driver Initilization. v3.1  512 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43288052
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver cdc_eem
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_subset
register rt2860


=== pAd = c0182000, size = 2135856 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc0080000, csr_addr=0xc0080000!
device_id =0x7662
==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
RtmpOSFileOpen(): Error 2 opening /etc/Wireless/iNIC/iNIC_ap.dat
Open file "/etc/Wireless/iNIC/iNIC_ap.dat" failed!
###########################################
###########################################
Read Parameters from default_profile_buffer
###########################################
###########################################
mbss> fatal error! beacon offset is error in driver! Please re-assign HW_BEACON_OFFSET!
RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=2
NVM is efuse and the information is too less to bring up the interface
Force to use Flash mode
NVM is FLASH mode (pAd->flash_offset = 0x48000)
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai


=== pAd = c0502000, size = 2135856 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc0400000, csr_addr=0xc0400000!
device_id =0x7662
==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860/RT2860.dat
Open file "/etc/Wireless/RT2860/RT2860.dat" failed!
###########################################
###########################################
Read Parameters from default_profile_buffer
###########################################
###########################################
mbss> fatal error! beacon offset is error in driver! Please re-assign HW_BEACON_OFFSET!
RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=2
NVM is efuse and the information is too less to bring up the interface
Force to use Flash mode
NVM is FLASH mode (pAd->flash_offset = 0x40000)
get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=ra
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
xhc_mtk xhc_mtk: xHCI Host Controller
xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1
xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000
------------> USB3.0 is Disabled
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
xhc_mtk xhc_mtk: xHCI Host Controller
xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2
------------> USB3.0 is Disabled
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i8042.c: i8042 controller self test timeout.
Trying to free nonexistent resource <0000000000000060-000000000000006f>
MTK MSDC device init.
msdc0 -> ops_get_cd return<0> <- msdc_ops_get_cd() : L<2317> PID<kworker/u:1><0x28>
mtk-sd: MediaTek MT6575 MSDC Driver
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3955 buckets, 15820 max)
NETDETECT target register
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
ip_nat_bnet: Trying to register for port 6112
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
TCP cubic registered
Twin IP Module Init
--> Init Smart QoS Monitor
Init SKIP Netfilter
NET: Registered protocol family 17
L2TP core driver, V2.0
L2TP netlink interface
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
List of all partitions:
1f00           16128 mtdblock0 (driver?)
1f01             128 mtdblock1 (driver?)
1f02              64 mtdblock2 (driver?)
1f03              64 mtdblock3 (driver?)
1f04            2176 mtdblock4 (driver?)
1f05           13952 mtdblock5 (driver?)
No filesystem could mount root, tried:  ext3 ext2 ext4 squashfs vfat fuseblk