dir 615 c1刷openwrt CC15.05.1无无线，求助

zx***

本帖最后由 zxcvb 于 2017-1-18 21:17 编辑

为利用教育网中的IPV6及校园网中的l2tp v p n，淘出了dir 615 c1刷openwrt CC15.05.1，除无无线外，其余正常。检查了无线部分，发现无线部分无MAC地址，手工加上MAC地址，无线正常。问题是这样操作，每次启动后都要人工添加无线部分的MAC地址。
请问，为何刷OP后无线部分丢失MAC地址，如何解决？
ps，刷回dir615的固件后，无线正常。该路由先前刷过DD，DD中无线也正常。

wehap***

主要是你的mac没有写到固定位置所以才需要每次启动都写入无线也是一样道理如果你可以刷个不死breed进去的话改一次资料后就可以稳定了

tes***

刷合适的ART就可以了，然后在breed里填上MAC码刷入，日后就不会再丢无线了

dant***

觉得可能是eeprom丢失了。

zx***

谢谢楼上各位大虾的指点。

zx***

查了art部分

root@OpenWrt:/etc# cat /proc/mtd
dev: size erasesize name
mtd0: 00020000 00010000 "u-boot"
mtd1: 00010000 00010000 "config"
mtd2: 003c0000 00010000 "firmware"
mtd3: 0011f40c 00010000 "kernel"
mtd4: 002a0bf4 00010000 "rootfs"
mtd5: 00080000 00010000 "rootfs_data"
mtd6: 00010000 00010000 "art"

zx***

art 部分
root@OpenWrt:/etc# cat /dev/mtd6 |hexdump
0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0001200 0cb8 1526 e015 0201 0000 001f 0019 e066
0001210 6668 0707 0000 0000 0000 0007 1b00 0400
0001220 0000 0000 0000 0000 0000 0000 0000 0000
*
0001290 0000 002d 0b0b 0b0b 0b0b e0b8 0e0e 0e00
00012a0 020e 00ca caca 0901 0000 0000 0000 0602
00012b0 0200 0000 0e0e 0000 0000 0000 002d 0000
00012c0 0000 0000 0000 0000 0000 0000 0000 0000
00012d0 0000 0000 8000 0000 0000 0000 0000 0000
00012e0 0000 0000 0000 0000 0001 bfc0 0001 bfc0
00012f0 0001 bfc0 0000 1120 0000 002d 1717 170a
0001300 0a0a deb0 0d0d 0d00 020e 1cff ffff 0a01
0001310 0000 0000 0000 0607 0400 0000 0e0e 0000
0001320 0000 0000 0038 0000 0000 0000 0000 0000
0001330 0000 0000 0000 0000 0000 0000 8000 0000
0001340 0000 0000 0000 0000 0000 0000 0000 0000
0001350 0000 0000 0000 0000 7089 acff 0000 0000
0001360 0000 0000 0000 0000 0000 0000 0000 0000
*
0001710 0000 0000 0000 0000 0000 0000 000e 1c2a
0001720 382a 343d 474f 0000 0000 0000 0000 0000
0001730 121e 3251 8815 1e2a 3a4a 0000 0000 0000
0001740 0000 0000 010f 1d2b 3929 333c 464e 0000
0001750 0000 0000 0000 0000 1522 3a5e 9b18 202d
0001760 3d4d 0000 0000 0000 0000 0000 010f 1d2b
0001770 3929 333c 454c 0000 0000 0000 0000 0000
0001780 1522 395e 9918 202d 3b4b 0000 0000 0000
0001790 0000 0000 0000 0000 0000 0000 0000 0000
*
00017b0 0000 0000 0000 0000 0000 0000 000e 1c2a
00017c0 382a 343d 454e 0000 0000 0000 0000 0000
00017d0 0e18 2740 6c12 1923 2e3d 0000 0000 0000
00017e0 0000 0000 010f 1d2b 3929 333c 444d 0000
00017f0 0000 0000 0000 0000 0f1a 2b49 7813 1b24
0001800 2e3f 0000 0000 0000 0000 0000 000e 1c2a
0001810 382a 343d 454e 0000 0000 0000 0000 0000
0001820 101c 2e4b 7b15 1c27 3145 0000 0000 0000
0001830 0000 0000 0000 0000 0000 0000 0000 0000
*
0001850 0000 0000 0000 0000 0000 0000 000e 1c2a
0001860 382a 343e 474f 0000 0000 0000 0000 0000
0001870 121d 304e 7f14 1f2a 3846 0000 0000 0000
0001880 0000 0000 010f 1d2b 3929 333d 464d 0000
0001890 0000 0000 0000 0000 1321 3759 9015 1e2b
00018a0 3947 0000 0000 0000 0000 0000 000e 1c2a
00018b0 382a 343d 464d 0000 0000 0000 0000 0000
00018c0 1422 365a 9017 222d 3b49 0000 0000 0000
00018d0 0000 0000 0000 0000 0000 0000 0000 0000
*
00018f0 0000 0000 0000 0000 0000 0000 4c22 201e
0001900 1a68 2220 1e1a b422 201e 1acd 2220 1e1a
0001910 ff00 0000 00ff 0000 0000 ff00 0000 00ff
0001920 0000 0000 4c22 2222 2222 2218 1458 2222
0001930 2222 2222 1814 6822 2222 2222 2218 148c
0001940 2222 2222 2222 1814 b422 2222 2222 2218
0001950 14bd 2222 2222 2222 1814 cd22 2222 2222
0001960 2218 14ff 0000 0000 0000 0000 4c22 2222
0001970 2222 2218 1458 2222 2222 2222 1814 6822
0001980 2222 2222 2218 148c 2222 2222 2222 1814
0001990 b422 2222 2222 2218 14bd 2222 2222 2222
00019a0 1814 cd22 2222 2222 2218 14ff 0000 0000
00019b0 0000 0000 7026 2626 26b8 2626 2626 ff00
00019c0 0000 0070 2222 201a 8922 2220 1aac 2222
00019d0 201a ff00 0000 0070 2626 2626 2622 1a16
00019e0 8926 2626 2626 221a 16ac 2626 2626 2622
00019f0 1a16 ff00 0000 0000 0000 0070 2626 2626
0001a00 2622 1a16 8926 2626 2626 221a 16ac 2626
0001a10 2626 2622 1a16 ff00 0000 0000 0000 0010
0001a20 1618 1112 1517 4046 4142 4530 3638 3132
0001a30 3537 0000 0000 004c 1e50 5e5c 6268 228c
0001a40 2290 62b4 22bd 624c 1e50 5e5c 6268 228c
*
0001a60 2290 62b4 22bd 624c 1e50 5e68 228c 62a0
0001a70 62b4 62bd 62cd 224c 1e50 5e68 228c 62a0
*
0001a90 62b4 62bd 62cd 224e 1e56 5e5e 628e 629e
0001aa0 62ae 22bf 60c7 604e 1e56 5e5e 628e 629e
*
0001ac0 62ae 22bf 60c7 6070 2475 66a2 2400 0000
0001ad0 0000 0000 0000 0070 2475 66a2 2400 0000
*
0001af0 0000 0000 0000 0070 2175 649d 64a2 2100
*
0001b20 0000 0000 0000 0070 2175 64a2 2100 0000
*
0001b50 0000 0000 0000 007a 217f 6493 6498 2100
*
0001b80 0000 0000 0000 004a 6250 625c 6268 6200
*
0001bb0 0000 0000 0000 004a 5b50 5b5c 5b68 5b00
*
0001be0 0000 0000 0000 0070 2875 68a2 28ac 28b8
0001bf0 2800 0000 0000 0070 2875 68a2 28ac 28b8
*
0001c10 2800 0000 0000 0070 2875 68a2 28ac 2800
0001c20 0000 0000 0000 0070 2875 68a2 28ac 2800
*
0001c40 0000 0000 0000 0070 2275 6298 2200 0000
*
0001c70 0000 0000 0000 004c 2268 228c 22b4 22bd
0001c80 62c1 62cd 2200 004c 2268 228c 22b4 22bd
*
0001ca0 62c1 62cd 2200 004c 1d50 5d68 1d8c 61a0
0001cb0 61b4 61bd 61cd 214c 1d50 5d68 1d8c 61a0
*
0001cd0 61b4 61bd 61cd 214e 1d56 5d66 1d8e 619e
0001ce0 61ae 2100 0000 004e 1d56 5d66 1d8e 619e
*
0001d00 61ae 2100 0000 0070 2075 60ac 2000 0000
0001d10 0000 0000 0000 0070 2075 60ac 2000 0000
*
0001d30 0000 0000 0000 0070 1d75 5dac 1d00 0000
*
0001d60 0000 0000 0000 0070 1c75 5cac 1c00 0000
*
0001d90 0000 0000 0000 007a 1c7f 5c93 5c98 1c00
*
0001dc0 0000 0000 0000 0000 0000 0000 0000 0000
*
0001eb0 0000 0000 0000 0000 ffff ffff ffff ffff
0001ec0 ffff ffff ffff ffff ffff ffff ffff ffff
*
0010000

zx***

无法找到有线与无线部分的MAC
可有线部分正常。
无线部分在rc.local 中加入
echo "XX:XX:XX:XX:XX:40" >/sys/class/ieee80211/phy0/macaddress
wifi up
无线部分能起，但wifi拒绝连接

zx***

boot log文件如下
[ 0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47269) ) #1 Sun Jan 31 18:39:35 CET 2016
[ 0.000000] MyLoader: sysp=114e2451, boardp=6761c593, parts=11c00018
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9130 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000]  memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 803762b0, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[ 0.000000] Kernel command line:  board=DIR-615-C1 console=ttyS0,115200 mtdparts=spi0.0:128k(u-boot)ro,64k(config)ro,3840k(firmware),64k(art)ro rootfstype=s
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28324K/32768K available (2586K kernel code, 128K rwdata, 540K rodata, 256K init, 193K bss, 4444K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:100.000MHz, Ref:5.000MHz
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is D-Link DIR-615 rev. C1
[ 0.160000] ar71xx: invalid mac address "............................................................................^P"
[ 0.620000] Switched to clocksource MIPS
[ 0.630000] NET: Registered protocol family 2
[ 0.630000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.630000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.640000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.650000] TCP: reno registered
[ 0.650000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.650000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.660000] NET: Registered protocol family 1
[ 0.670000] PCI: CLS 0 bytes, default 32
[ 0.670000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.680000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.690000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.700000] msgmni has been set to 55
[ 0.700000] io scheduler noop registered
[ 0.710000] io scheduler deadline registered (default)
[ 0.710000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.720000] console [ttyS0] disabled
[ 0.750000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 6250000) is a 16550A
[ 0.760000] console [ttyS0] enabled
[ 0.760000] bootconsole [early0] disabled
[ 0.790000] m25p80 spi0.0: found mx25l3205d, expected m25p80
[ 0.800000] m25p80 spi0.0: mx25l3205d (4096 Kbytes)
[ 0.800000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.810000] Creating 4 MTD partitions on "spi0.0":
[ 0.810000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.820000] 0x000000020000-0x000000030000 : "config"
[ 0.820000] 0x000000030000-0x0000003f0000 : "firmware"
[ 0.840000] 2 uimage-fw partitions found on MTD device firmware
[ 0.850000] 0x000000030000-0x00000014f40c : "kernel"
[ 0.860000] 0x00000014f40c-0x0000003f0000 : "rootfs"
[ 0.860000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.870000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.880000] 0x000000370000-0x0000003f0000 : "rootfs_data"
[ 0.880000] 0x0000003f0000-0x000000400000 : "art"
[ 0.900000] switch0: Atheros AR8216 rev. 1 switch registered on ag71xx-mdio.0
[ 0.910000] libphy: ag71xx_mdio: probed
[ 1.260000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd042, driver=Atheros AR8216/AR8236/AR8316]
[ 1.270000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RMII
[ 1.600000] ag71xx ag71xx.1: connected to PHY at ag71xx-mdio.0:04 [uid=004dd042, driver=Atheros AR8216/AR8236/AR8316]
[ 1.610000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RMII
[ 1.620000] TCP: cubic registered
[ 1.620000] NET: Registered protocol family 17
[ 1.620000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.640000] Bridge firewalling registered
[ 1.640000] 8021q: 802.1Q VLAN Support v1.8
[ 1.660000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.660000] Freeing unused kernel memory: 256K (80390000 - 803d0000)
[ 3.290000] init: Console is alive
[ 3.300000] init: - watchdog -
[ 5.390000] init: - preinit -
[ 6.270000] random: procd urandom read with 9 bits of entropy available
[ 7.490000] ar71xx: pll_reg 0xb8050014: 0x13000a44
[ 7.490000] eth0: link up (100Mbps/Full duplex)
[ 9.500000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:04: Port 4 is up
[ 9.580000] jffs2: notice: (333) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead,
[ 9.600000] mount_root: switching to jffs2 overlay
[ 9.650000] eth0: link down
[ 9.660000] procd: - early -
[ 9.670000] procd: - watchdog -
[ 10.520000] procd: - ubus -
[ 11.530000] procd: - init -
[ 12.470000] NET: Registered protocol family 10
[ 12.480000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.500000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 12.510000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 12.520000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.540000] nf_conntrack version 0.5.0 (446 buckets, 1784 max)
[ 12.580000] xt_time: kernel timezone is -0000
[ 12.620000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.620000] cfg80211: World regulatory domain updated:
[ 12.630000] cfg80211:  DFS Master region: unset
[ 12.630000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.640000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.650000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 12.660000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.670000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 12.680000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 12.690000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 12.700000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.700000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 12.780000] PPP generic driver version 2.4.2
[ 12.790000] NET: Registered protocol family 24
[ 12.880000] ath: EEPROM regdomain: 0x0
[ 12.880000] ath: EEPROM indicates default country code should be used
[ 12.880000] ath: doing EEPROM country->regdmn map search
[ 12.880000] ath: country maps to regdmn code: 0x3a
[ 12.880000] ath: Country alpha2 being used: US
[ 12.880000] ath: Regpair used: 0x3a
[ 12.900000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 12.900000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a2 mem=0xb80c0000, irq=2
[ 12.920000] cfg80211: Calling CRDA for country: US
[ 12.930000] cfg80211: Regulatory domain changed to country: US
[ 12.930000] cfg80211:  DFS Master region: FCC
[ 12.940000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.950000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 12.960000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A)
[ 12.970000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 12.970000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s)
[ 12.980000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 12.990000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 20.890000] device eth0 entered promiscuous mode
[ 20.890000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.920000] device eth1 entered promiscuous mode
[ 20.950000] br-wan6: port 1(eth1) entered forwarding state
[ 20.950000] br-wan6: port 1(eth1) entered forwarding state
[ 22.610000] br-wan6: port 1(eth1) entered disabled state
[ 22.870000] ar71xx: pll_reg 0xb8050014: 0x13000a44
[ 22.870000] eth0: link up (100Mbps/Full duplex)
[ 23.220000] br-lan: port 1(eth0) entered forwarding state
[ 23.220000] br-lan: port 1(eth0) entered forwarding state
[ 23.230000] cfg80211: Calling CRDA for country: CN
[ 23.230000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 23.260000] cfg80211: Regulatory domain changed to country: CN
[ 23.260000] cfg80211:  DFS Master region: FCC
[ 23.270000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 23.280000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 23.280000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A)
[ 23.290000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 23.300000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 23.310000] cfg80211: (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
[ 23.320000] cfg80211: (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4400 mBm), (N/A)
[ 23.330000] cfg80211: (63720000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
[ 25.220000] br-lan: port 1(eth0) entered forwarding state
[ 74.320000] random: nonblocking pool is initialized
[  205.390000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  205.430000] device wlan0 entered promiscuous mode
[  212.800000] device wlan0 left promiscuous mode
[  212.810000] br-wan6: port 2(wlan0) entered disabled state
[  213.050000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  213.220000] device wlan0 entered promiscuous mode
[  227.080000] br-lan: port 2(wlan0) entered disabled state
[  227.090000] device wlan0 left promiscuous mode
[  227.100000] br-lan: port 2(wlan0) entered disabled state
[  231.940000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  231.960000] device wlan0 entered promiscuous mode
[  239.310000] device wlan0 left promiscuous mode
[  239.320000] br-wan6: port 2(wlan0) entered disabled state
[  239.470000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  239.550000] device wlan0 entered promiscuous mode
[  241.340000] br-lan: port 2(wlan0) entered disabled state
[  241.350000] device wlan0 left promiscuous mode
[  241.360000] br-lan: port 2(wlan0) entered disabled state
[  253.280000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  253.330000] device wlan0 entered promiscuous mode
[  261.670000] br-wan6: port 2(wlan0) entered forwarding state
[  261.680000] br-wan6: port 2(wlan0) entered forwarding state
[  261.680000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  263.670000] br-wan6: port 2(wlan0) entered forwarding state
[  272.140000] device wlan0 left promiscuous mode
[  272.140000] br-wan6: port 2(wlan0) entered disabled state
[  272.830000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  272.860000] device wlan0 entered promiscuous mode
[  272.860000] br-wan6: port 2(wlan0) entered forwarding state
[  272.870000] br-wan6: port 2(wlan0) entered forwarding state
[  273.140000] br-wan6: port 2(wlan0) entered disabled state
[  273.160000] device eth1 left promiscuous mode
[  273.160000] br-wan6: port 1(eth1) entered disabled state
[  273.170000] device wlan0 left promiscuous mode
[  273.170000] br-wan6: port 2(wlan0) entered disabled state
[  273.180000] device eth1 entered promiscuous mode
[  273.220000] IPv6: ADDRCONF(NETDEV_UP): br-wan6: link is not ready
[  277.250000] br-lan: port 1(eth0) entered disabled state
[  277.310000] device eth0 left promiscuous mode
[  277.310000] br-lan: port 1(eth0) entered disabled state
[  277.370000] eth0: link down
[  277.370000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[  277.440000] device eth0 entered promiscuous mode
[  277.450000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[  279.160000] ar71xx: pll_reg 0xb8050014: 0x13000a44
[  279.160000] eth0: link up (100Mbps/Full duplex)
[  279.160000] br-lan: port 1(eth0) entered forwarding state
[  279.170000] br-lan: port 1(eth0) entered forwarding state
[  279.170000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  281.170000] br-lan: port 1(eth0) entered forwarding state
[  281.250000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  292.040000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  292.060000] device wlan0 entered promiscuous mode
[  292.060000] br-wan6: port 2(wlan0) entered forwarding state
[  292.070000] br-wan6: port 2(wlan0) entered forwarding state
[  292.150000] IPv6: ADDRCONF(NETDEV_CHANGE): br-wan6: link becomes ready
[  292.450000] br-wan6: port 2(wlan0) entered disabled state
[  300.420000] br-wan6: port 2(wlan0) entered forwarding state
[  300.420000] br-wan6: port 2(wlan0) entered forwarding state
[  300.430000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  302.420000] br-wan6: port 2(wlan0) entered forwarding state
[  308.610000] device wlan0 left promiscuous mode
[  308.610000] br-wan6: port 2(wlan0) entered disabled state
[  314.410000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  314.460000] device wlan0 entered promiscuous mode
[  322.620000] br-lan: port 1(eth0) entered disabled state
[  322.630000] device eth0 left promiscuous mode
[  322.630000] br-lan: port 1(eth0) entered disabled state
[  322.640000] eth0: link down
[  322.640000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[  322.720000] device eth0 entered promiscuous mode
[  322.720000] br-lan: port 1(eth0) entered forwarding state
[  322.730000] br-lan: port 1(eth0) entered forwarding state
[  322.800000] br-wan6: port 2(wlan0) entered forwarding state
[  322.810000] br-wan6: port 2(wlan0) entered forwarding state
[  322.810000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  323.620000] br-lan: port 1(eth0) entered disabled state
[  324.160000] ar71xx: pll_reg 0xb8050014: 0x13000a44
[  324.160000] eth0: link up (100Mbps/Full duplex)
[  324.160000] br-lan: port 1(eth0) entered forwarding state
[  324.170000] br-lan: port 1(eth0) entered forwarding state
[  324.810000] br-wan6: port 2(wlan0) entered forwarding state
[  326.170000] br-lan: port 1(eth0) entered forwarding state
[  333.620000] device wlan0 left promiscuous mode
[  333.620000] br-wan6: port 2(wlan0) entered disabled state
[  334.370000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  334.420000] device wlan0 entered promiscuous mode
[  334.420000] br-wan6: port 2(wlan0) entered forwarding state
[  334.430000] br-wan6: port 2(wlan0) entered forwarding state
[  334.630000] br-wan6: port 2(wlan0) entered disabled state
[  342.790000] br-wan6: port 2(wlan0) entered forwarding state
[  342.790000] br-wan6: port 2(wlan0) entered forwarding state
[  342.800000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  344.790000] br-wan6: port 2(wlan0) entered forwarding state

zx***

请大虾指点

账号		自动登录	找回密码
密码			立即注册

dir 615 c1刷openwrt CC15.05.1无无线，求助

相关帖子

欢迎大家光临恩山无线论坛 /1