麻烦恩山指点一下，8230刷了wrtsl54gs的cfe，不稳定

空虚真人

昨天测试了几个小时，刷了论坛里面提供的wrtsl54gs的cfe，刷入DD，刷了最近的两个版本，11805和11995，是std版和std-usb的，都发现不太稳定，有断流和重启的现象

在ttl里面能看到重启的信息

等晚上再测试一下其他版本的DD和TT看看，估计不会有很明显的效果，因为其他版本我在别的路由器上试过，还算稳定

请恩山指点一下排除故障的思路

顺便说一下，如果是原厂的cfe，倒是很稳定，文件拷贝和bt，迅雷都还可以，但似乎没有看到别人提到这样的问题

[ 本帖最后由 bestdoctors 于 2009-4-27 13:31 编辑 ]

yy5409

只有改了128MB内存要激活才刷wrtsl54gs的cfe，否则，不建议刷的！！！
我的G108都改了128MB内存不过没有刷wrtsl54gs的cfe，只当64MB用，考虑到不脱机下载用不了那么大，以后再说！！！

[ 本帖最后由 yy5409 于 2009-4-27 18:58 编辑 ]

5417

bestdoctors ,上128M内存了嘛？
一次性成功？

空虚真人

没有，只有32M内存

我刷wrtsl的cfe是为了刷大一点的固件。因为原厂固件不能刷大于3.5M的

而wrtsl的cfe能刷甚至3.8M的固件

yy5409

那就难怪不稳定了，这个CFE是为128mb内存准备的，不是为多用一点FLASH容量准备的，呵呵！！！

空虚真人

这样啊？有这样的说法？难道wrtsl 54gs本身就是128M内存？

准备再试试几个其他版本的固件。如果实在不行就只好刷回原来的cfe了，不折腾8230了

贴一下启动信息

CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Mon Dec 26 17:51:02 CST 2005 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena
Initializing Devices.

No DPN
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.37.0
rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
et1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.37.0
CPU type 0x29006: 264MHz
Total memory: 32768 KBytes

Total memory used by CFE:  0x80300000 - 0x803A39C0 (670144)
Initialized Data:          0x803398D0 - 0x8033BFE0 (10000)
BSS Area:                  0x8033BFE0 - 0x8033D9C0 (6624)
Local Heap:                0x8033D9C0 - 0x803A19C0 (409600)
Stack Area:                0x803A19C0 - 0x803A39C0 (8192)
Text (code) segment:       0x80300000 - 0x803398D0 (235728)
Boot area (physical):      0x003A4000 - 0x003E4000
Relocation Factor:         I:00000000 - D:00000000

Boot version: v3.7
The boot is CFE

No mac find, use default mac

eou_key_init(): Find key pair in location 0
The eou device id is same
The eou public key is same
The eou private key is same
Device eth0:  hwaddr 00-11-50-2F-12-04, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Reading :: Failed.: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3920 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
CPU ProcId is: 0x00029006, options: 0x0000004d
Linux version 2.4.37 (eko@dd-wrt) (gcc version 3.4.6 (OpenWrt-2.0)) #3371 Thu Apr 23 12:58:20 CEST 2009
Setting the PFC to its default value
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
CPU: BCM4704 rev 8 at 264 MHz
Using 132.000 MHz high precision timer.
Calibrating delay loop... 263.78 BogoMIPS
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
PCI: Initializing host
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 01:00.0 to 64
PCI: Fixing up bus 1
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 3) is a 16550A
PCI: Setting latency timer of device 00:01.0 to 64
PCI: Setting latency timer of device 00:02.0 to 64
PCI: Setting latency timer of device 01:01.0 to 64
PCI: Enabling device 01:01.0 (0004 -> 0006)
Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Flash device: 0x400000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0x2ad618
partition size = 2872320
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x003f0000 : "linux"
0x00122c00-0x003e0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x003f0000-0x00400000 : "nvram"
0x003e0000-0x003f0000 : "ddwrt"
sflash not supported on this router
Initializing Cryptographic API
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
ip_conntrack version 2.1 (512 buckets, 4096 max) - 336 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_random match loaded
netfilter PSD loaded - (c) astaro AG
ipt_osf: Startng OS fingerprint matching module.
ipt_IPV4OPTSSTRIP loaded
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
starting Architecture code for broadcom
Booting device: Linksys WRTSL54GS
boardflags are 0x0018
enable Afterburner, boardflags are 0x0218
sh: can't create /proc/sys/net/ipv4/tcp_congestion_control: nonexistent directory
eth2: Operation not supported
wl0.2: No such device
wl0.3: No such device
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
wl0.1: Invalid argument
br0: Bad file descriptor
br0: Bad file descriptor
eth2: Operation not supported
wl0.2: No such device
wl0.3: No such device
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
wl0.1: Invalid argument
wl0_mode: No such device
eth2: Operation not supported
wl0.2: No such device
wl0.3: No such device
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
wl0.1: Invalid argument
Setting SSID "Belkin 8230"
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Key is a RSA key
Wrote key to '/tmp/root/.ssh/ssh_host_rsa_key'
Key is a DSS key
Wrote key to '/tmp/root/.ssh/ssh_host_dss_key'
eth2: No such process
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
sh: /tmp/.rc_startup: not found

[ 本帖最后由 bestdoctors 于 2009-4-29 01:02 编辑 ]

yy5409

看看这个的拆解http://www.topwifi.cn/thread-184-1-1.html

空虚真人

已经重新测试了WRTSL54GS和300N的cfe，发现不稳定可能与超频有关

而根据我自己的实验和论坛其他人的试验，在原厂CFE的情况下，超频到300M其实是非常稳定的。但是不知为何第三方CFE却不稳定

如果是WRTSL，能开机，能工作，但是有重启和断流的情况，而300N更是彻底，干脆不启动，连TTL 窗口里面都看不到任何的启动信息，只能用jtag清空nvram才能启动（reset的问题尚未解决）

awingpotato

佩服楼主的精神。支持折腾。

空虚真人

昨天夜里拷机拷了一夜，似乎很稳定了，这次没有超频了

看起来问题解决了

yy5409

G108(8230)的硬重启的问题解决了???