|
贴上ttl跑马如下:
Xshell 5 (Build 1124)
Copyright (c) 2002-2017 NetSarang Computer, Inc. All rights reserved.
Type `help' to learn how to use Xshell prompt.
[c:\~]$
Connecting to COM7...
Connected.
Digital core power voltage set to 1.05V
Detect memory size = 256 MB
Post lines...ok
Memory check ok!
Decompressing...done
Digital core power voltage set to 1.05V
Detect memory size = 256 MB
Post lines...ok
Memory check ok!
Decompressing...done
Found a AMD NAND flash:
Total size: 512MB
Block size: 128KB
Page Size: 2048B
OOB Size: 64B
Sector size: 512B
Spare size: 16B
ECC level: 4 (4-bit)
Device ID: 0x01 0xdc 0x90 0x95 0x56 0x01
board=8, clk=1400
CFE version v1.0.4
BSP: 7.14.116 (r549303) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Thu Feb 18 11:37:14 CST 2016 (jenkins@JenkinsServer)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot up from NAND flash...
Boot partition size = 262144(0x40000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1400,*800*
XXXXX chipattach,538: Don't need override the robosw port5 setting
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.116 (r549303)
CPU type 0x0: 1400MHz
Tot mem: 262144 KBytes
CFE mem: 0x00F00000 - 0x0179135C (8983388)
Data: 0x00F59748 - 0x00F59DC0 (1656)
BSS: 0x00F59DD0 - 0x00F8F35C (218508)
Heap: 0x00F8F35C - 0x0178F35C (8388608)
Stack: 0x0178F35C - 0x0179135C (8192)
Text: 0x00F00000 - 0x00F4D68C (317068)
Boot: 0x01792000 - 0x017D2000
Reloc: I:00000000 - D:00000000
Device eth0: hwaddr 28-6C-07-5D-E8-79, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
bootargs: boot -loader=raw_brcmnand -addr=0x8000 nflash0.os1:
Loader:raw_brcmnand Filesys:raw Dev:nflash0.os1 File: Optionsnull)
Loading: compressed crc = 0xd1545136 3137536 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.36 (jenkins@48251e92e4b1) (gcc version 4.8.2 20130603 (prerelease) (crosstool-NG 1.19.0) ) #3 MiWiFi-R2D-2.25.209 SMP PREEMPT Tue Oct 16 11:45:02 UTC 2018
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Northstar Prototype
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] MPCORE found at 19020000
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c8206000 s5568 r8192 d14912 u65536
[ 0.000000] pcpu-alloc: s5568 r8192 d14912 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/ram rw console=ttyS0,115200 init=/init libata.force=3.0Gbps
[ 0.000000] System in normal state
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 253228k/253228k available, 8916k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xf7e00000 - 0xffe00000 ( 128 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xf0000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0139000 (1220 kB)
[ 0.000000] .text : 0xc0139000 - 0xc058f000 (4440 kB)
[ 0.000000] .data : 0xc05aa000 - 0xc05d3d00 ( 168 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:256
[ 0.000000] MPCORE GIC init
[ 0.000000] External imprecise Data abort at addr=0x0, fsr=0x1c06 ignored.
[ 0.000000] Found chip type NAI (0x3f00cf26)
[ 0.000000] Chipc: rev 42, caps 0x48000a, chipst 0x0 pmurev 0, pmucaps 0x0
[ 0.000000] si_kattach done. ccrev = 42, wd_msticks = 125000
[ 0.000000] MPCORE Global Timer Clock 700000000Hz
[ 0.000000] allocated 1310720 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Calibrating delay loop... 2798.38 BogoMIPS (lpj=13991936)
[ 0.250000] pid_max: default: 32768 minimum: 301
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] Initializing cgroup subsys memory
[ 0.250000] Initializing cgroup subsys net_cls
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] MPCORE Private timer setup CPU0
[ 0.250000] Calibrating local timer... 699.879MHz.
[ 0.340000] L310: cache controller enabled 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x7a130800
[ 0.380000] CPU1: Booted secondary processor
[ 0.380000] MPCORE Private timer setup CPU1
[ 0.640000] Brought up 2 CPUs
[ 0.640000] SMP: Total of 2 processors activated (5596.77 BogoMIPS).
[ 0.640000] devtmpfs: initialized
[ 0.640000] atomic64 test passed
[ 0.640000] NET: Registered protocol family 16
[ 0.640000] Found a AMD NAND flash:
[ 0.640000] Total size: 512MB
[ 0.640000] Block size: 128KB
[ 0.640000] Page Size: 2048B
[ 0.640000] OOB Size: 64B
[ 0.640000] Sector size: 512B
[ 0.640000] Spare size: 16B
[ 0.640000] ECC level: 4 (4-bit)
[ 0.640000] Device ID: 0x 1 0xdc 0x90 0x95 0x56 0x01
[ 0.650000] CCA UART Clock Config: Sel=1 Ovr=1 Div=48
[ 0.650000] CCA UART Clock rate 125000000Hz CCB UART Clock rate 125000000Hz
[ 0.650000] ACP (Accelerator Coherence Port) enabled
[ 0.660000] bio: create slab <bio-0> at 0
[ 0.660000] SCSI subsystem initialized
[ 0.660000] usbcore: registered new interface driver usbfs
[ 0.660000] usbcore: registered new interface driver hub
[ 0.660000] usbcore: registered new device driver usb
[ 0.660000] DEV + ,register_netdevice, lo, paddr: cf821800
[ 0.660000] Switching to clocksource mpcore_gtimer
[ 0.660000] NET: Registered protocol family 2
[ 0.660000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.660000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.660000] TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
[ 0.660000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.660000] TCP reno registered
[ 0.660000] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.660000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.660000] NET: Registered protocol family 1
[ 0.660000] system bringup monitor is running...
[ 1.020000] PCI: no core
[ 1.020000] PCI: no core
[ 1.020000] ai_flag: Attempting to read CHIPCOMMONB DMP registers on 4707
[ 1.020000] PCI: scanning bus 0
[ 1.020000] PCI: Fixing up bus 0
[ 1.270000] PCIE1 link=0
[ 1.520000] PCIE2 link=1
[ 1.520000] PCIE2 switching to GEN2
[ 1.770000] PCIE2 link=1
[ 1.770000] PCI: Fixing up bus 0
[ 1.770000] PCI: bus0: Fast back to back transfers disabled
[ 1.770000] PCI: Fixing up bus 1
[ 1.770000] PCI: bus1: Fast back to back transfers disabled
[ 1.770000] pci 0002:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 1.770000] pci 0002:01:00.0: BAR 0: assigned [mem 0x20000000-0x20007fff 64bit]
[ 1.770000] pci 0002:01:00.0: BAR 0: set to [mem 0x20000000-0x20007fff 64bit] (PCI address [0x20000000-0x20007fff]
[ 1.770000] pci 0002:00:00.0: PCI bridge to [bus 01-01]
[ 1.770000] pci 0002:00:00.0: bridge window [io disabled]
[ 1.770000] pci 0002:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 1.770000] pci 0002:00:00.0: bridge window [mem pref disabled]
[ 2.020000] PCIE3 link=1
[ 2.020000] PCIE3 switching to GEN2
[ 2.270000] PCIE3 link=1
[ 2.270000] PCI: Fixing up bus 0
[ 2.270000] PCI: bus0: Fast back to back transfers disabled
[ 2.270000] PCI: Fixing up bus 1
[ 2.270000] PCI: bus1: Fast back to back transfers disabled
[ 2.280000] pci 0003:00:00.0: BAR 8: assigned [mem 0x28000000-0x280fffff]
[ 2.280000] pci 0003:01:00.0: BAR 5: assigned [mem 0x28000000-0x280001ff]
[ 2.280000] pci 0003:01:00.0: BAR 5: set to [mem 0x28000000-0x280001ff] (PCI address [0x28000000-0x280001ff]
[ 2.280000] pci 0003:01:00.0: BAR 4: can't assign io (size 0x10)
[ 2.280000] pci 0003:01:00.0: BAR 0: can't assign io (size 0x8)
[ 2.280000] pci 0003:01:00.0: BAR 2: can't assign io (size 0x8)
[ 2.280000] pci 0003:01:00.0: BAR 1: can't assign io (size 0x4)
[ 2.280000] pci 0003:01:00.0: BAR 3: can't assign io (size 0x4)
[ 2.280000] pci 0003:00:00.0: PCI bridge to [bus 01-01]
[ 2.280000] pci 0003:00:00.0: bridge window [io disabled]
[ 2.280000] pci 0003:00:00.0: bridge window [mem 0x28000000-0x280fffff]
[ 2.280000] pci 0003:00:00.0: bridge window [mem pref disabled]
[ 2.280000] VFS: Disk quotas dquot_6.5.2
[ 2.280000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.280000] msgmni has been set to 494
[ 2.280000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.280000] io scheduler noop registered
[ 2.280000] io scheduler deadline registered
[ 2.280000] io scheduler cfq registered (default)
[ 2.280000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 2.280000] serial8250.0: ttyS0 at MMIO 0x18000300 (irq = 117) is a 16550
[ 2.990000] console [ttyS0] enabled
[ 2.990000] serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
[ 3.000000] init reset module!
[ 3.000000] brd: module loaded
[ 3.010000] loop: module loaded
[ 3.010000] PCI: Enabling device 0003:01:00.0 (0140 -> 0142)
[ 3.020000] ahci: SSS flag set, parallel bus scan disabled
[ 3.020000] ahci 0003:01:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl IDE mode
[ 3.030000] ahci 0003:01:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs
[ 3.040000] scsi0 : ahci
[ 3.040000] scsi1 : ahci
[ 3.040000] ata1: FORCE: PHY spd limit set to 3.0Gbps
[ 3.050000] ata1: SATA max UDMA/133 abar m512@0x28000000 port 0x28000100 irq 175
[ 3.060000] ata2: FORCE: PHY spd limit set to 3.0Gbps
[ 3.060000] ata2: SATA max UDMA/133 abar m512@0x28000000 port 0x28000180 irq 175
[ 3.420000] ata1: SATA link down (SStatus 0 SControl 320)
[ 3.770000] ata2: SATA link down (SStatus 0 SControl 320)
[ 5.320000] Creating 8 MTD partitions on "nflash":
[ 5.330000] 0x000000000000-0x000000080000 : "boot"
[ 5.330000] 0x000000080000-0x000000100000 : "nvram"
[ 5.340000] 0x000000100000-0x000000140000 : "board_data"
[ 5.340000] 0x000000140000-0x000000180000 : "crash"
[ 5.350000] 0x000000180000-0x000000200000 : "rsvd0"
[ 5.350000] 0x000000200000-0x000000600000 : "os0"
[ 5.360000] 0x000000600000-0x000000a00000 : "os1"
[ 5.360000] 0x000000a00000-0x000001000000 : "rsvd1"
[ 5.370000] PPP generic driver version 2.4.2
[ 5.370000] NET: Registered protocol family 24
[ 5.380000] DEV + ,register_netdevice, ifb0, paddr: cf04b800
[ 5.380000] Netlink kernel socket create failed
[ 5.390000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.400000] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 5.410000] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
[ 5.440000] ehci_hcd 0000:00:0b.1: irq 111, io mem 0x18021000
[ 5.460000] ehci_hcd 0000:00:0b.1: USB 0.0 started, EHCI 1.00
[ 5.460000] hub 1-0:1.0: USB hub found
[ 5.460000] hub 1-0:1.0: 2 ports detected
[ 5.470000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.480000] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 5.480000] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
[ 5.490000] ohci_hcd 0000:00:0b.0: irq 111, io mem 0x18022000
[ 5.550000] hub 2-0:1.0: USB hub found
[ 5.550000] hub 2-0:1.0: 2 ports detected
[ 5.560000] Initializing USB Mass Storage driver...
[ 5.560000] usbcore: registered new interface driver usb-storage
[ 5.570000] USB Mass Storage support registered.
[ 5.570000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
[ 5.580000] Netfilter messages via NETLINK v0.30 with ipset netlink.patch.
[ 5.590000] nf_conntrack version 0.5.0 (3956 buckets, 15824 max)
[ 5.600000] ctnetlink v0.93: registering with nfnetlink.
[ 5.600000] TCP cubic registered
[ 5.600000] NET: Registered protocol family 10
[ 5.610000] NET: Registered protocol family 17
[ 5.610000] L2TP core driver, V2.0
[ 5.620000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 5.620000] All bugs added by David S. Miller <davem@redhat.com>
[ 5.640000] Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
[ 5.650000] NAND device: Manufacturer ID: 0x01, Chip ID: 0xdc (AMD NAND 512MiB 3,3V 8-bit)
[ 5.660000] Spare area=64 eccbytes 28, ecc bytes located at:
[ 5.670000] 9 10 11 12 13 14 15 25 26 27 28 29 30 31 41 42 43 44 45 46 47 57 58 59 60 61 62 63
[ 5.680000] Available 35 bytes at (off,len):
[ 5.680000] (1,8) (16,9) (32,9) (48,9) (0,0) (0,0) (0,0) (0,0)
[ 5.690000] Scanning device for bad blocks
[ 7.950000] Options: NO_AUTOINCR,NO_READRDY,NO_SUBPAGE_WRITE,BBT_SCAN2NDPAGE,
[ 7.960000] Creating 3 MTD partitions on "brcmnand":
[ 7.960000] 0x000001000000-0x000009000000 : "rootfs0"
[ 7.970000] 0x000009000000-0x000011000000 : "rootfs1"
[ 7.970000] 0x000011000000-0x000020000000 : "overlay"
[ 7.980000] Freeing init memory: 1220K
[ 8.000000] Loading essential drivers...
[ 8.050000] Check for USB rescure...
[ 8.060000] Press Ctrl+C to enter RAMFS...
[ 9.070000] INFO: No Hard Disk
[ 9.070000] Bringup the system...
[ 9.080000] UBI: attaching mtd9 to ubi1
[ 9.090000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 9.090000] UBI: logical eraseblock size: 126976 bytes
[ 9.100000] UBI: smallest flash I/O unit: 2048
[ 9.100000] UBI: VID header offset: 2048 (aligned 2048)
[ 9.110000] UBI: data offset: 4096
[ 9.950000] UBI: max. sequence number: 5
[ 9.970000] UBI: attached mtd9 to ubi1
[ 9.970000] UBI: MTD device name: "rootfs1"
[ 9.980000] UBI: MTD device size: 128 MiB
[ 9.980000] UBI: number of good PEBs: 1024
[ 9.990000] UBI: number of bad PEBs: 0
[ 9.990000] UBI: max. allowed volumes: 128
[ 9.990000] UBI: wear-leveling threshold: 4096
[ 10.000000] UBI: number of internal volumes: 1
[ 10.000000] UBI: number of user volumes: 1
[ 10.010000] UBI: available PEBs: 0
[ 10.010000] UBI: total number of reserved PEBs: 1024
[ 10.020000] UBI: number of PEBs reserved for bad PEB handling: 40
[ 10.020000] UBI: max/mean erase counter: 5/2
[ 10.030000] UBI: image sequence number: 559895222
[ 10.030000] UBI: background thread "ubi_bgt1d" started, PID 402
UBI device number 1, total 1024 LEBs (130023424 bytes, 124.0 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 10.140000] UBIFS: mounted UBI device 1, volume 0, name "system"
[ 10.150000] UBIFS: mounted read-only
[ 10.150000] UBIFS: file system size: 123039744 bytes (120156 KiB, 117 MiB, 969 LEBs)
[ 10.160000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[ 10.170000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 10.180000] UBIFS: default compressor: none
[ 10.180000] UBIFS: reserved for root: 0 bytes (0 KiB)
config core 'version'
# ROM ver
option ROM '2.25.209'
# channel
option CHANNEL 'stable'
# hardware platform R1AC or R1N etc.
option HARDWARE 'R2D'
# CFE ver
option UBOOT '1.0.2'
# Linux Kernel ver
option LINUX '0.0.1'
# RAMFS ver
option RAMFS '0.0.1'
# SQUASHFS ver
option SQAFS '0.0.1'
# ROOTFS ver
option ROOTFS '0.0.1'
#build time
option BUILDTIME 'Tue, 16 Oct 2018 11:21:13 +0000'
#build timestamp
option BUILDTS '1539688873'
#build git tag
option GTAG 'commit f617d73c957fe11a260770f38004851c3da6e31f'
- preinit -
Tue Oct 16 11:45:02 UTC 2018
- regular preinit -
/lib/preinit.sh: line 1: pi_indicate_led: not found
/lib/preinit.sh: line 1: jffs2_not_mounted: not found
[ 10.680000] UBI: attaching mtd10 to ubi2
[ 10.680000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 10.690000] UBI: logical eraseblock size: 126976 bytes
[ 10.690000] UBI: smallest flash I/O unit: 2048
[ 10.700000] UBI: VID header offset: 2048 (aligned 2048)
[ 10.710000] UBI: data offset: 4096
[ 12.280000] UBI: max. sequence number: 18461
[ 12.290000] UBI: attached mtd10 to ubi2
[ 12.300000] UBI: MTD device name: "overlay"
[ 12.300000] UBI: MTD device size: 240 MiB
[ 12.310000] UBI: number of good PEBs: 1920
[ 12.310000] UBI: number of bad PEBs: 0
[ 12.320000] UBI: max. allowed volumes: 128
[ 12.320000] UBI: wear-leveling threshold: 4096
[ 12.330000] UBI: number of internal volumes: 1
[ 12.330000] UBI: number of user volumes: 1
[ 12.340000] UBI: available PEBs: 0
[ 12.340000] UBI: total number of reserved PEBs: 1920
[ 12.350000] UBI: number of PEBs reserved for bad PEB handling: 76
[ 12.350000] UBI: max/mean erase counter: 8867/1564
[ 12.360000] UBI: image sequence number: 601507813
[ 12.360000] UBI: background thread "ubi_bgt2d" started, PID 439
UBI device number 2, total 1920 LEBs (243793920 bytes, 232.5 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 12.420000] UBIFS: recovery needed
[ 12.490000] UBIFS: recovery completed
[ 12.490000] UBIFS: mounted UBI device 2, volume 0, name "data"
[ 12.500000] UBIFS: file system size: 232239104 bytes (226796 KiB, 221 MiB, 1829 LEBs)
[ 12.500000] UBIFS: journal size: 11681792 bytes (11408 KiB, 11 MiB, 92 LEBs)
[ 12.510000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 12.520000] UBIFS: default compressor: none
[ 12.520000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
Primary disk mount failed: No block device.
System fail flag set. Do etc recovery
WARNING: No etc_bak folder
*****ota: remove files in /etc/remove.conf *****
- init -
init started: BusyBox v1.19.4 (2018-10-16 11:10:12 UTC)
rcS S boot: INFO: rc script run time limit to 65 seconds.
(none) login: [ 15.640000] ctf: module license 'Proprietary' taints kernel.
[ 15.640000] Disabling lock debugging due to kernel taint
[ 15.660000] DEV + ,register_netdevice, dpsta, paddr: cf13a800
[ 15.690000] et_module_init: passivemode set to 0x0
[ 15.700000] et_module_init: txworkq set to 0x0
[ 15.700000] et_module_init: et_txq_thresh set to 0x400
[ 15.710000] et_module_init: et_rxlazy_timeout set to 0x3e8
[ 15.710000] et_module_init: et_rxlazy_framecnt set to 0x20
[ 15.720000] si_doattach: incoming bus is PCI but it's a lie, switching to SI devid:0x4715
[ 15.730000] Found chip type NAI (0x3f00cf26)
[ 15.730000] Chipc: rev 42, caps 0x48000a, chipst 0x0 pmurev 0, pmucaps 0x0
[ 15.740000] XXXXX chipattach,538: Don't need override the robosw port5 setting
[ 15.750000] DEV + ,register_netdevice, eth0, paddr: cf13b800
[ 15.760000] eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.116 (r549303)
[ 16.090000] tun: Universal TUN/TAP device driver, 1.6
[ 16.090000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 16.120000] PPP MPPE Compression module registered
[ 16.130000] Mirror/redirect action on
[ 16.150000] u32 classifier
[ 16.160000] Actions configured
[ 16.270000] IPv6 over IPv4 tunneling driver
[ 16.270000] DEV + ,register_netdevice, sit0, paddr: cf13f800
[ 16.290000] GRE over IPv4 demultiplexor driver
[ 16.300000] GRE over IPv4 tunneling driver
[ 16.310000] DEV + ,register_netdevice, gre0, paddr: cdb18000
[ 16.310000] ipgre init: can't add protocol
[ 16.320000] DEV - ,unregister_netdevice_queue, gre0, paddr: cdb18000
[ 16.380000] DEV , netdev_run_todo, release dev, gre0, paddr: cdb18000
[ 16.470000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.530000] xt_time: kernel timezone is +0800
[ 16.570000] PPPoL2TP kernel driver, V2.0
[ 16.580000] p p t p driver version 0.8.5
[ 16.600000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 16.780000] ipt: xt_cgroup_MARK installed ok.
[ 16.970000] ip_set: protocol 6
[ 17.360000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 17.370000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 17.410000] ipaccount: ifname [lo] event[5]
[ 17.410000] ipaccount: ifname [ifb0] event[5]
[ 17.410000] ipaccount: ifname [dpsta] event[5]
[ 17.420000] ipaccount: ifname [eth0] event[5]
[ 17.420000] ipaccount: ifname [sit0] event[5]
[ 17.460000] fuse init (API version 7.15)
[ 19.140000] wl_module_init: msglevel set to 0x0
[ 19.140000] wl_module_init: msglevel2 set to 0x0
[ 19.150000] wl_module_init: phymsglevel set to 0x0
[ 19.150000] wl_module_init: passivemode set to 0x0
[ 19.160000] wl_module_init: txworkq set to 0x0
[ 19.160000] PCI: Enabling device 0002:01:00.0 (0140 -> 0142)
[ 19.170000] Found chip type AI (0x1380a8d1)
[ 19.170000] Chipc: rev 39, caps 0x18500000, chipst 0x6 pmurev 12, pmucaps 0x108c260c
[ 19.190000] initvars_cis_pci: Not CIS format
[ 19.190000] ipxotp_read_region: h/w region not programmed
[ 19.200000] Neither SPROM nor OTP has valid image
[ 19.200000] srom rev:0
[ 19.210000] MIN and MAX mask is not programmed
[ 19.230000] ipaccount: ifname [wl0] event[16]
[ 19.230000] DEV + ,register_netdevice, wl0, paddr: cdc0b000
[ 19.240000] ipaccount: ifname [wl0] event[5]
[ 19.240000] wl0: Broadcom BCM43227 802.11 Wireless Controller 7.14.116 (r549303 WLTEST) (Compiled in . at 11:08:41 on Oct 16 2018)
rcS S calling: /etc/rc.d/S10boot boot: WARNING: EXITCODE=0, execute too slow, 38 >= 15: /etc/rc.d/S10boot boot
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: INFO: loading exist /etc/config/network.
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: config switch 'eth0'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option enable '1'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: config switch_vlan 'eth0_1'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option device 'eth0'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option vlan '1'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option ports '0 2 3 5*'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: config switch_vlan 'eth0_2'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option device 'eth0'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option vlan '2'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option ports '4 5'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: config interface 'loopback'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option ifname 'lo'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option proto 'static'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option ipaddr '127.0.0.1'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option netmask '255.0.0.0'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: config interface 'lan'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option type 'bridge'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option ifname 'eth0.1'
Tue Oct 16 19:45:44 CST 2018 netconfig[3360]: option proto 'static'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: option ipaddr '192.168.31.1'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: option netmask '255.255.255.0'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: option ip6assign '64'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: list ip6class 'ifb'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: list ip6class 'ipv66'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: config interface 'ifb'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: option ifname 'ifb0'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: config interface 'ready'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: option proto 'static'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: option ipaddr '169.254.29.1'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: option netmask '255.255.255.0'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: config interface 'wan'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: option ifname 'eth0.2'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: option proto 'dhcp'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: config interface 'openvirtual**'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: option ifname 'tun0'
Tue Oct 16 19:45:45 CST 2018 netconfig[3360]: option proto 'openvirtual**'
[ 54.370000] ipaccount: ifname [br-lan] event[16]
[ 54.370000] DEV + ,register_netdevice, br-lan, paddr: cda77000
[ 54.380000] ipaccount: ifname [br-lan] event[5]
[ 54.380000] ipaccount: ifname [eth0] event[13]
[ 54.390000] ipaccount: ifname [eth0] event[1]
[ 54.390000] ipaccount: ifname [eth0.1] event[16]
[ 54.400000] DEV + ,register_netdevice, eth0.1, paddr: cdb19800
[ 54.400000] ipaccount: ifname [eth0.1] event[5]
[ 54.410000] ipaccount: ifname [eth0.1] event[13]
[ 54.410000] ipaccount: ifname [eth0.1] event[1]
[ 54.420000] device eth0.1 entered promiscuous mode
[ 54.420000] device eth0 entered promiscuous mode
[ 54.430000] ipaccount: ifname [br-lan] event[8]
[ 54.430000] ipaccount: ifname [br-lan] event[13]
[ 54.440000] br-lan: port 1(eth0.1) entering learning state
[ 54.440000] br-lan: port 1(eth0.1) entering learning state
[ 54.450000] ipaccount: ifname [br-lan] event[1]
[ 54.460000] ipaccount: ifname [ifb0] event[13]
[ 54.460000] ipaccount: ifname [ifb0] event[1]
[ 54.470000] ipaccount: ifname [lo] event[13]
[ 54.470000] ipaccount: ifname [lo] event[1]
[ 54.480000] ipaccount: ifname [eth0.2] event[16]
[ 54.490000] DEV + ,register_netdevice, eth0.2, paddr: ce3ba000
[ 54.490000] ipaccount: ifname [eth0.2] event[5]
[ 54.500000] ipaccount: ifname [eth0.2] event[13]
[ 54.500000] ipaccount: ifname [eth0.2] event[1]
[ 55.390000]
[ 55.390000] robo_link_down: applying EEE WAR for 53125 port 0 link-down
[ 55.390000] robo_link_down: applying EEE WAR for 53125 port 1 link-down
[ 55.400000] robo_link_down: applying EEE WAR for 53125 port 2 link-downipaccount: ifname [eth0.2] event[4]
[ 55.410000]
[ 55.410000] robo_link_down: applying EEE WAR for 53125 port 4 link-down
[ 56.440000] br-lan: port 1(eth0.1) entering forwarding state
[ 56.970000] ctf: bytes_threshold 3MB(3145728B), mask F00000, old_mark: 200000, new_mark: 400000
[ 58.260000] ipaccount: ifname [wl0] event[8]
[ 58.450000] device wl0 entered promiscuous mode
[ 61.020000] ctf: bytes_threshold 3MB(3145728B), mask F00000, old_mark: 200000, new_mark: 400000
[ 63.590000] ipaccount: ifname [wl0] event[13]
[ 63.590000] br-lan: port 2(wl0) entering learning state
[ 63.600000] br-lan: port 2(wl0) entering learning state
[ 63.600000] ipaccount: ifname [wl0] event[1]
[ 64.420000]
[ 64.420000] robo_link_down: applying EEE WAR for 53125 port 3 link-down
[ 65.610000] br-lan: port 2(wl0) entering forwarding state
[ 67.440000]
[ 67.440000] robo_link_down: applying EEE WAR for 53125 port 3 link-upTue Oct 16 19:46:00 CST 2018 boot_check[8205]: WARNING: no wireless device available
[ 69.580000] Restarting system.
Digital core power voltage set to 1.05V
Detect memory size = 256 MB
Post lines...ok
Memory check ok!
Decompressing...done
Digital core power voltage set to 1.05V
Detect memory size = 256 MB
Post lines...ok
Memory check ok!
Decompressing...done
Found a AMD NAND flash:
Total size: 512MB
Block size: 128KB
Page Size: 2048B
OOB Size: 64B
Sector size: 512B
Spare size: 16B
ECC level: 4 (4-bit)
Device ID: 0x01 0xdc 0x90 0x95 0x56 0x01
board=8, clk=1400
CFE version v1.0.4
BSP: 7.14.116 (r549303) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Thu Feb 18 11:37:14 CST 2016 (jenkins@JenkinsServer)
Copyright (C) 2000-2008 Broadcom Corporation.
下面就是无限重启了,另外有一个好的 R2D,跑马如下,求大神分析
Xshell 5 (Build 1124)
Copyright (c) 2002-2017 NetSarang Computer, Inc. All rights reserved.
Type `help' to learn how to use Xshell prompt.
[c:\~]$
Connecting to COM7...
Connected.
Digital core power voltage set to 1.05V
Detect memory size = 256 MB
Post lines...ok
Memory check ok!
Decompressing...done
Digital core power voltage set to 1.05V
Detect memory size = 256 MB
Post lines...ok
Memory check ok!
Decompressing...done
Found a AMD NAND flash:
Total size: 512MB
Block size: 128KB
Page Size: 2048B
OOB Size: 64B
Sector size: 512B
Spare size: 16B
ECC level: 4 (4-bit)
Device ID: 0x01 0xdc 0x90 0x95 0x56 0x01
board=8, clk=1400
CFE version v1.0.4
BSP: 7.14.116 (r549303) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Thu Sep 10 14:59:17 CST 2015 (szy@szy-rommaker)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot up from NAND flash...
Boot partition size = 262144(0x40000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1400,*800*
XXXXX chipattach,538: Don't need override the robosw port5 setting
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.116 (r549303)
CPU type 0x0: 1400MHz
Tot mem: 262144 KBytes
CFE mem: 0x00F00000 - 0x0179135C (8983388)
Data: 0x00F59748 - 0x00F59DC0 (1656)
BSS: 0x00F59DD0 - 0x00F8F35C (218508)
Heap: 0x00F8F35C - 0x0178F35C (8388608)
Stack: 0x0178F35C - 0x0179135C (8192)
Text: 0x00F00000 - 0x00F4D68C (317068)
Boot: 0x01792000 - 0x017D2000
Reloc: I:00000000 - D:00000000
Device eth0: hwaddr F0-B4-29-84-5E-EE, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
bootargs: boot -loader=raw_brcmnand -addr=0x8000 nflash0.os1:
Loader:raw_brcmnand Filesys:raw Dev:nflash0.os1 File: Optionsnull)
Loading: compressed crc = 0x64332844 3137536 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.36 (jenkins@JenkinsServer) (gcc version 4.8.2 20130603 (prerelease) (crosstool-NG 1.19.0) ) #3 MiWiFi-R2D-2.24.10 SMP PREEMPT Fri Oct 20 11:51:48 CST 2017
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Northstar Prototype
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] MPCORE found at 19020000
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c8206000 s5568 r8192 d14912 u65536
[ 0.000000] pcpu-alloc: s5568 r8192 d14912 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/ram rw console=ttyS0,115200 init=/init libata.force=3.0Gbps
[ 0.000000] System in normal state
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 253228k/253228k available, 8916k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xf7e00000 - 0xffe00000 ( 128 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xf0000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0139000 (1220 kB)
[ 0.000000] .text : 0xc0139000 - 0xc058f000 (4440 kB)
[ 0.000000] .data : 0xc05aa000 - 0xc05d3ca0 ( 168 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:256
[ 0.000000] MPCORE GIC init
[ 0.000000] External imprecise Data abort at addr=0x0, fsr=0x1c06 ignored.
[ 0.000000] Found chip type NAI (0x3f00cf26)
[ 0.000000] Chipc: rev 42, caps 0x48000a, chipst 0x0 pmurev 0, pmucaps 0x0
[ 0.000000] si_kattach done. ccrev = 42, wd_msticks = 125000
[ 0.000000] MPCORE Global Timer Clock 700000000Hz
[ 0.000000] allocated 1310720 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Calibrating delay loop... 2798.38 BogoMIPS (lpj=13991936)
[ 0.250000] pid_max: default: 32768 minimum: 301
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] Initializing cgroup subsys memory
[ 0.250000] Initializing cgroup subsys net_cls
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] MPCORE Private timer setup CPU0
[ 0.250000] Calibrating local timer... 699.784MHz.
[ 0.340000] L310: cache controller enabled 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x7a130800
[ 0.380000] CPU1: Booted secondary processor
[ 0.380000] MPCORE Private timer setup CPU1
[ 0.640000] Brought up 2 CPUs
[ 0.640000] SMP: Total of 2 processors activated (5596.77 BogoMIPS).
[ 0.640000] devtmpfs: initialized
[ 0.640000] atomic64 test passed
[ 0.640000] NET: Registered protocol family 16
[ 0.640000] Found a AMD NAND flash:
[ 0.640000] Total size: 512MB
[ 0.640000] Block size: 128KB
[ 0.640000] Page Size: 2048B
[ 0.640000] OOB Size: 64B
[ 0.640000] Sector size: 512B
[ 0.640000] Spare size: 16B
[ 0.640000] ECC level: 4 (4-bit)
[ 0.640000] Device ID: 0x 1 0xdc 0x90 0x95 0x56 0x01
[ 0.650000] CCA UART Clock Config: Sel=1 Ovr=1 Div=48
[ 0.650000] CCA UART Clock rate 125000000Hz CCB UART Clock rate 125000000Hz
[ 0.650000] ACP (Accelerator Coherence Port) enabled
[ 0.660000] bio: create slab <bio-0> at 0
[ 0.660000] SCSI subsystem initialized
[ 0.660000] usbcore: registered new interface driver usbfs
[ 0.660000] usbcore: registered new interface driver hub
[ 0.660000] usbcore: registered new device driver usb
[ 0.660000] DEV + ,register_netdevice, lo, paddr: cf821800
[ 0.660000] Switching to clocksource mpcore_gtimer
[ 0.660000] NET: Registered protocol family 2
[ 0.660000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.660000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.660000] TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
[ 0.660000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.660000] TCP reno registered
[ 0.660000] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.660000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.660000] NET: Registered protocol family 1
[ 0.660000] system bringup monitor is running...
[ 1.020000] PCI: no core
[ 1.020000] PCI: no core
[ 1.020000] ai_flag: Attempting to read CHIPCOMMONB DMP registers on 4707
[ 1.020000] PCI: scanning bus 0
[ 1.020000] PCI: Fixing up bus 0
[ 1.270000] PCIE1 link=1
[ 1.270000] PCIE1 switching to GEN2
[ 1.520000] PCIE1 link=1
[ 1.520000] PCI: Fixing up bus 0
[ 1.520000] PCI: bus0: Fast back to back transfers disabled
[ 1.520000] PCI: Fixing up bus 1
[ 1.520000] PCI: bus1: Fast back to back transfers disabled
[ 1.520000] pci 0001:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff]
[ 1.520000] pci 0001:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit]
[ 1.520000] pci 0001:01:00.0: BAR 0: set to [mem 0x08000000-0x08007fff 64bit] (PCI address [0x8000000-0x8007fff]
[ 1.520000] pci 0001:00:00.0: PCI bridge to [bus 01-01]
[ 1.520000] pci 0001:00:00.0: bridge window [io disabled]
[ 1.520000] pci 0001:00:00.0: bridge window [mem 0x08000000-0x080fffff]
[ 1.520000] pci 0001:00:00.0: bridge window [mem pref disabled]
[ 1.770000] PCIE2 link=1
[ 1.770000] PCIE2 switching to GEN2
[ 2.020000] PCIE2 link=1
[ 2.020000] PCI: Fixing up bus 0
[ 2.020000] PCI: bus0: Fast back to back transfers disabled
[ 2.020000] PCI: Fixing up bus 1
[ 2.020000] PCI: bus1: Fast back to back transfers disabled
[ 2.020000] pci 0002:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 2.020000] pci 0002:01:00.0: BAR 0: assigned [mem 0x20000000-0x20007fff 64bit]
[ 2.020000] pci 0002:01:00.0: BAR 0: set to [mem 0x20000000-0x20007fff 64bit] (PCI address [0x20000000-0x20007fff]
[ 2.020000] pci 0002:00:00.0: PCI bridge to [bus 01-01]
[ 2.020000] pci 0002:00:00.0: bridge window [io disabled]
[ 2.020000] pci 0002:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 2.020000] pci 0002:00:00.0: bridge window [mem pref disabled]
[ 2.270000] PCIE3 link=1
[ 2.270000] PCIE3 switching to GEN2
[ 2.520000] PCIE3 link=1
[ 2.520000] PCI: Fixing up bus 0
[ 2.520000] PCI: bus0: Fast back to back transfers disabled
[ 2.520000] PCI: Fixing up bus 1
[ 2.520000] PCI: bus1: Fast back to back transfers disabled
[ 2.520000] pci 0003:00:00.0: BAR 8: assigned [mem 0x28000000-0x280fffff]
[ 2.520000] pci 0003:01:00.0: BAR 5: assigned [mem 0x28000000-0x280001ff]
[ 2.520000] pci 0003:01:00.0: BAR 5: set to [mem 0x28000000-0x280001ff] (PCI address [0x28000000-0x280001ff]
[ 2.520000] pci 0003:01:00.0: BAR 4: can't assign io (size 0x10)
[ 2.520000] pci 0003:01:00.0: BAR 0: can't assign io (size 0x8)
[ 2.520000] pci 0003:01:00.0: BAR 2: can't assign io (size 0x8)
[ 2.520000] pci 0003:01:00.0: BAR 1: can't assign io (size 0x4)
[ 2.520000] pci 0003:01:00.0: BAR 3: can't assign io (size 0x4)
[ 2.520000] pci 0003:00:00.0: PCI bridge to [bus 01-01]
[ 2.520000] pci 0003:00:00.0: bridge window [io disabled]
[ 2.520000] pci 0003:00:00.0: bridge window [mem 0x28000000-0x280fffff]
[ 2.520000] pci 0003:00:00.0: bridge window [mem pref disabled]
[ 2.530000] VFS: Disk quotas dquot_6.5.2
[ 2.530000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.530000] msgmni has been set to 494
[ 2.530000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.530000] io scheduler noop registered
[ 2.530000] io scheduler deadline registered
[ 2.530000] io scheduler cfq registered (default)
[ 2.530000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 2.530000] serial8250.0: ttyS0 at MMIO 0x18000300 (irq = 117) is a 16550
[ 3.310000] console [ttyS0] enabled
[ 3.310000] serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
[ 3.320000] init reset module!
[ 3.320000] brd: module loaded
[ 3.330000] loop: module loaded
[ 3.330000] PCI: Enabling device 0003:01:00.0 (0140 -> 0142)
[ 3.340000] ahci: SSS flag set, parallel bus scan disabled
[ 3.340000] ahci 0003:01:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl IDE mode
[ 3.350000] ahci 0003:01:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs
[ 3.360000] scsi0 : ahci
[ 3.360000] scsi1 : ahci
[ 3.360000] ata1: FORCE: PHY spd limit set to 3.0Gbps
[ 3.370000] ata1: SATA max UDMA/133 abar m512@0x28000000 port 0x28000100 irq 175
[ 3.380000] ata2: FORCE: PHY spd limit set to 3.0Gbps
[ 3.380000] ata2: SATA max UDMA/133 abar m512@0x28000000 port 0x28000180 irq 175
[ 3.740000] ata1: SATA link down (SStatus 0 SControl 320)
[ 4.090000] ata2: SATA link down (SStatus 0 SControl 320)
[ 5.640000] Creating 8 MTD partitions on "nflash":
[ 5.650000] 0x000000000000-0x000000080000 : "boot"
[ 5.650000] 0x000000080000-0x000000100000 : "nvram"
[ 5.660000] 0x000000100000-0x000000140000 : "board_data"
[ 5.660000] 0x000000140000-0x000000180000 : "crash"
[ 5.670000] 0x000000180000-0x000000200000 : "rsvd0"
[ 5.670000] 0x000000200000-0x000000600000 : "os0"
[ 5.680000] 0x000000600000-0x000000a00000 : "os1"
[ 5.680000] 0x000000a00000-0x000001000000 : "rsvd1"
[ 5.690000] PPP generic driver version 2.4.2
[ 5.690000] NET: Registered protocol family 24
[ 5.700000] DEV + ,register_netdevice, ifb0, paddr: cd2ca000
[ 5.700000] Netlink kernel socket create failed
[ 5.710000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.720000] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 5.720000] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
[ 5.760000] ehci_hcd 0000:00:0b.1: irq 111, io mem 0x18021000
[ 5.780000] ehci_hcd 0000:00:0b.1: USB 0.0 started, EHCI 1.00
[ 5.780000] hub 1-0:1.0: USB hub found
[ 5.780000] hub 1-0:1.0: 2 ports detected
[ 5.790000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.800000] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 5.800000] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
[ 5.810000] ohci_hcd 0000:00:0b.0: irq 111, io mem 0x18022000
[ 5.870000] hub 2-0:1.0: USB hub found
[ 5.870000] hub 2-0:1.0: 2 ports detected
[ 5.880000] Initializing USB Mass Storage driver...
[ 5.880000] usbcore: registered new interface driver usb-storage
[ 5.890000] USB Mass Storage support registered.
[ 5.890000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
[ 5.900000] Netfilter messages via NETLINK v0.30 with ipset netlink.patch.
[ 5.910000] nf_conntrack version 0.5.0 (3956 buckets, 15824 max)
[ 5.920000] ctnetlink v0.93: registering with nfnetlink.
[ 5.920000] TCP cubic registered
[ 5.920000] NET: Registered protocol family 10
[ 5.930000] NET: Registered protocol family 17
[ 5.930000] L2TP core driver, V2.0
[ 5.940000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 5.940000] All bugs added by David S. Miller <davem@redhat.com>
[ 5.960000] Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
[ 5.970000] NAND device: Manufacturer ID: 0x01, Chip ID: 0xdc (AMD NAND 512MiB 3,3V 8-bit)
[ 5.980000] Spare area=64 eccbytes 28, ecc bytes located at:
[ 5.990000] 9 10 11 12 13 14 15 25 26 27 28 29 30 31 41 42 43 44 45 46 47 57 58 59 60 61 62 63
[ 6.000000] Available 35 bytes at (off,len):
[ 6.000000] (1,8) (16,9) (32,9) (48,9) (0,0) (0,0) (0,0) (0,0)
[ 6.010000] Scanning device for bad blocks
[ 8.270000] Options: NO_AUTOINCR,NO_READRDY,NO_SUBPAGE_WRITE,BBT_SCAN2NDPAGE,
[ 8.280000] Creating 3 MTD partitions on "brcmnand":
[ 8.280000] 0x000001000000-0x000009000000 : "rootfs0"
[ 8.290000] 0x000009000000-0x000011000000 : "rootfs1"
[ 8.290000] 0x000011000000-0x000020000000 : "overlay"
[ 8.300000] Freeing init memory: 1220K
[ 8.320000] Loading essential drivers...
[ 8.370000] Check for USB rescure...
[ 8.380000] Press Ctrl+C to enter RAMFS...
[ 9.390000] INFO: No Hard Disk
[ 9.390000] Bringup the system...
[ 9.400000] UBI: attaching mtd9 to ubi1
[ 9.410000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 9.410000] UBI: logical eraseblock size: 126976 bytes
[ 9.420000] UBI: smallest flash I/O unit: 2048
[ 9.420000] UBI: VID header offset: 2048 (aligned 2048)
[ 9.430000] UBI: data offset: 4096
[ 10.270000] UBI: max. sequence number: 3
[ 10.290000] UBI: attached mtd9 to ubi1
[ 10.290000] UBI: MTD device name: "rootfs1"
[ 10.290000] UBI: MTD device size: 128 MiB
[ 10.300000] UBI: number of good PEBs: 1024
[ 10.300000] UBI: number of bad PEBs: 0
[ 10.310000] UBI: max. allowed volumes: 128
[ 10.310000] UBI: wear-leveling threshold: 4096
[ 10.320000] UBI: number of internal volumes: 1
[ 10.320000] UBI: number of user volumes: 1
[ 10.330000] UBI: available PEBs: 0
[ 10.330000] UBI: total number of reserved PEBs: 1024
[ 10.340000] UBI: number of PEBs reserved for bad PEB handling: 40
[ 10.340000] UBI: max/mean erase counter: 25/2
[ 10.350000] UBI: image sequence number: 463699912
[ 10.350000] UBI: background thread "ubi_bgt1d" started, PID 406
UBI device number 1, total 1024 LEBs (130023424 bytes, 124.0 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 10.460000] UBIFS: mounted UBI device 1, volume 0, name "system"
[ 10.470000] UBIFS: mounted read-only
[ 10.470000] UBIFS: file system size: 123039744 bytes (120156 KiB, 117 MiB, 969 LEBs)
[ 10.480000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[ 10.490000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 10.490000] UBIFS: default compressor: none
[ 10.500000] UBIFS: reserved for root: 0 bytes (0 KiB)
config core 'version'
# ROM ver
option ROM '2.24.10'
# channel
option CHANNEL 'release'
# hardware platform R1AC or R1N etc.
option HARDWARE 'R2D'
# CFE ver
option UBOOT '1.0.2'
# Linux Kernel ver
option LINUX '0.0.1'
# RAMFS ver
option RAMFS '0.0.1'
# SQUASHFS ver
option SQAFS '0.0.1'
# ROOTFS ver
option ROOTFS '0.0.1'
#build time
option BUILDTIME 'Fri, 20 Oct 2017 11:38:33 +0800'
#build timestamp
option BUILDTS '1508470713'
#build git tag
option GTAG 'commit 34b1c281ef412e676880873cd56287be32a3b283'
- preinit -
Fri Oct 20 11:51:48 UTC 2017
- regular preinit -
/lib/preinit.sh: line 1: pi_indicate_led: not found
/lib/preinit.sh: line 1: jffs2_not_mounted: not found
[ 11.040000] UBI: attaching mtd10 to ubi2
[ 11.050000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 11.050000] UBI: logical eraseblock size: 126976 bytes
[ 11.060000] UBI: smallest flash I/O unit: 2048
[ 11.060000] UBI: VID header offset: 2048 (aligned 2048)
[ 11.070000] UBI: data offset: 4096
[ 12.640000] UBI: max. sequence number: 680
[ 12.660000] UBI: attached mtd10 to ubi2
[ 12.660000] UBI: MTD device name: "overlay"
[ 12.670000] UBI: MTD device size: 240 MiB
[ 12.670000] UBI: number of good PEBs: 1920
[ 12.680000] UBI: number of bad PEBs: 0
[ 12.680000] UBI: max. allowed volumes: 128
[ 12.680000] UBI: wear-leveling threshold: 4096
[ 12.690000] UBI: number of internal volumes: 1
[ 12.690000] UBI: number of user volumes: 1
[ 12.700000] UBI: available PEBs: 0
[ 12.700000] UBI: total number of reserved PEBs: 1920
[ 12.710000] UBI: number of PEBs reserved for bad PEB handling: 76
[ 12.710000] UBI: max/mean erase counter: 239/218
[ 12.720000] UBI: image sequence number: 1380813691
[ 12.720000] UBI: background thread "ubi_bgt2d" started, PID 443
UBI device number 2, total 1920 LEBs (243793920 bytes, 232.5 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 12.790000] UBIFS: recovery needed
[ 12.870000] UBIFS: recovery completed
[ 12.870000] UBIFS: mounted UBI device 2, volume 0, name "data"
[ 12.880000] UBIFS: file system size: 232239104 bytes (226796 KiB, 221 MiB, 1829 LEBs)
[ 12.890000] UBIFS: journal size: 11681792 bytes (11408 KiB, 11 MiB, 92 LEBs)
[ 12.900000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 12.900000] UBIFS: default compressor: none
[ 12.910000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
Primary disk mount failed: No block device.
- init -
init started: BusyBox v1.19.4 (2017-10-20 11:29:47 CST)
rcS S boot: INFO: rc script run time limit to 65 seconds.
(none) login: [ 14.550000] ctf: module license 'Proprietary' taints kernel.
[ 14.560000] Disabling lock debugging due to kernel taint
[ 14.570000] DEV + ,register_netdevice, dpsta, paddr: cd7c4800
[ 14.610000] et_module_init: passivemode set to 0x0
[ 14.610000] et_module_init: txworkq set to 0x0
[ 14.620000] et_module_init: et_txq_thresh set to 0x400
[ 14.620000] et_module_init: et_rxlazy_timeout set to 0x3e8
[ 14.630000] et_module_init: et_rxlazy_framecnt set to 0x20
[ 14.630000] si_doattach: incoming bus is PCI but it's a lie, switching to SI devid:0x4715
[ 14.640000] Found chip type NAI (0x3f00cf26)
[ 14.650000] Chipc: rev 42, caps 0x48000a, chipst 0x0 pmurev 0, pmucaps 0x0
[ 14.660000] XXXXX chipattach,538: Don't need override the robosw port5 setting
[ 14.670000] DEV + ,register_netdevice, eth0, paddr: cd7c5800
[ 14.670000] eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.116 (r549303)
[ 14.980000] tun: Universal TUN/TAP device driver, 1.6
[ 14.990000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 15.010000] PPP MPPE Compression module registered
[ 15.020000] Mirror/redirect action on
[ 15.050000] u32 classifier
[ 15.050000] Actions configured
[ 15.160000] IPv6 over IPv4 tunneling driver
[ 15.170000] DEV + ,register_netdevice, sit0, paddr: cd1c1800
[ 15.180000] GRE over IPv4 demultiplexor driver
[ 15.200000] GRE over IPv4 tunneling driver
[ 15.200000] DEV + ,register_netdevice, gre0, paddr: cd1c2800
[ 15.210000] ipgre init: can't add protocol
[ 15.210000] DEV - ,unregister_netdevice_queue, gre0, paddr: cd1c2800
[ 15.300000] DEV , netdev_run_todo, release dev, gre0, paddr: cd1c2800
[ 15.380000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.440000] xt_time: kernel timezone is +0800
[ 15.480000] PPPoL2TP kernel driver, V2.0
[ 15.500000] p p t p driver version 0.8.5
[ 15.510000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 15.700000] ipt: xt_cgroup_MARK installed ok.
[ 15.900000] ip_set: protocol 6
[ 16.250000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 16.260000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 16.300000] Traffic lan port is eth0
[ 16.340000] fuse init (API version 7.15)
[ 18.010000] wl_module_init: msglevel set to 0x0
[ 18.020000] wl_module_init: msglevel2 set to 0x0
[ 18.020000] wl_module_init: phymsglevel set to 0x0
[ 18.030000] wl_module_init: passivemode set to 0x0
[ 18.030000] wl_module_init: txworkq set to 0x0
[ 18.040000] Found chip type AI (0x15134352)
[ 18.040000] Chipc: rev 43, caps 0x58680001, chipst 0x9a69 pmurev 17, pmucaps 0x10a22b11
[ 18.050000] initvars_cis_pci: Not CIS format
[ 18.060000] ipxotp_read_region: h/w region not programmed
[ 18.060000] Neither SPROM nor OTP has valid image
[ 18.070000] srom rev:0
[ 18.070000] Overriding boardvendor: 0x14e4 instead of 0x14e4
[ 18.070000] ChangeVCO => vco:960, xtalF:40, frac: 98, ndivMode: 3, ndivint: 24
[ 18.080000] Data written into the PLL_CNTRL_ADDR2: 00000c31
[ 18.090000] Data written into the PLL_CNTRL_ADDR3 (Fractional): 0000100e
[ 18.100000] Changing rsrc 6 res_updn_timer to 0x200001
[ 18.100000] ALP in KHz is 40000, cur PM_REG_VAL is 0, new PM_REG_VAL is 50
[ 18.110000] pciedev_crwlpciegen2_180:Reg:0x1814 ::0x5305f
[ 18.120000] DEV + ,register_netdevice, wl0, paddr: cdbfa000
[ 18.130000] wl0: Broadcom BCM4360 802.11 Wireless Controller 7.14.116 (r549303 WLTEST) (Compiled in . at 11:28:57 on Oct 20 2017)
[ 18.140000] PCI: Enabling device 0002:01:00.0 (0140 -> 0142)
[ 18.150000] Found chip type AI (0x1380a8d1)
[ 18.150000] Chipc: rev 39, caps 0x18500000, chipst 0x6 pmurev 12, pmucaps 0x108c260c
[ 18.170000] initvars_cis_pci: Not CIS format
[ 18.170000] ipxotp_read_region: h/w region not programmed
[ 18.180000] Neither SPROM nor OTP has valid image
[ 18.180000] srom rev:0
[ 18.190000] MIN and MAX mask is not programmed
[ 18.210000] DEV + ,register_netdevice, wl1, paddr: ce2fa800
[ 18.220000] wl1: Broadcom BCM43227 802.11 Wireless Controller 7.14.116 (r549303 WLTEST) (Compiled in . at 11:28:57 on Oct 20 2017)
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: INFO: loading exist /etc/config/network.
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: config switch 'eth0'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option enable '1'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: config switch_vlan 'eth0_1'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option device 'eth0'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option vlan '1'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option ports '0 2 3 5*'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: config switch_vlan 'eth0_2'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option device 'eth0'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option vlan '2'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option ports '4 5'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: config interface 'loopback'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option ifname 'lo'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option proto 'static'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option ipaddr '127.0.0.1'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option netmask '255.0.0.0'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: config interface 'lan'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option type 'bridge'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option ifname 'eth0.1'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option proto 'static'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option ipaddr '192.168.31.1'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option netmask '255.255.255.0'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option ip6assign '64'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: list ip6class 'ifb'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: list ip6class 'ipv66'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: config interface 'ifb'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option ifname 'ifb0'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: config interface 'ready'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option proto 'static'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option ipaddr '169.254.29.1'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option netmask '255.255.255.0'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: config interface 'wan'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option ifname 'eth0.2'
Fri Oct 20 19:51:55 CST 2017 netconfig[913]: option proto 'dhcp'
[ 19.370000] DEV + ,register_netdevice, br-lan, paddr: ce706000
[ 19.370000] DEV + ,register_netdevice, eth0.1, paddr: ce70a000
[ 19.380000] device eth0.1 entered promiscuous mode
[ 19.380000] device eth0 entered promiscuous mode
[ 19.390000] br-lan: port 1(eth0.1) entering learning state
[ 19.400000] br-lan: port 1(eth0.1) entering learning state
[ 19.410000] DEV + ,register_netdevice, eth0.2, paddr: ce70e800
[ 20.370000]
[ 20.370000] robo_link_down: applying EEE WAR for 53125 port 0 link-down
[ 20.370000] robo_link_down: applying EEE WAR for 53125 port 1 link-down
[ 20.380000] robo_link_down: applying EEE WAR for 53125 port 2 link-down
[ 20.390000] robo_link_down: applying EEE WAR for 53125 port 3 link-down
[ 20.390000] robo_link_down: applying EEE WAR for 53125 port 4 link-down
[ 21.400000] br-lan: port 1(eth0.1) entering forwarding state
[ 22.490000] Changing rsrc 6 res_updn_timer to 0x200001
[ 22.500000] ALP in KHz is 40000, cur PM_REG_VAL is 0, new PM_REG_VAL is 50
[ 22.510000] ALP in KHz is 40000, cur PM_REG_VAL is 0, new PM_REG_VAL is 50
[ 22.510000] pciedev_crwlpciegen2_180:Reg:0x1814 ::0x5305f
[ 22.580000] ALP in KHz is 40000, cur PM_REG_VAL is 0, new PM_REG_VAL is 50
[ 22.590000] pciedev_crwlpciegen2_180:Reg:0x1814 ::0x5305f
[ 22.760000] ctf: bytes_threshold 3MB(3145728B), mask F00000, old_mark: 200000, new_mark: 400000
[ 22.810000] device wl0 entered promiscuous mode
[ 23.810000] DEV + ,register_netdevice, wl1.3, paddr: ce75f400
[ 24.000000] device wl1 entered promiscuous mode
[ 25.310000] tcpproxy_init, succeed!
[ 26.690000] ctf: bytes_threshold 3MB(3145728B), mask F00000, old_mark: 200000, new_mark: 400000
[ 27.860000] br-lan: port 2(wl0) entering learning state
[ 27.870000] br-lan: port 2(wl0) entering learning state
[ 27.950000] br-lan: port 3(wl1) entering learning state
[ 27.960000] br-lan: port 3(wl1) entering learning state
[ 29.870000] br-lan: port 2(wl0) entering forwarding state
[ 29.960000] br-lan: port 3(wl1) entering forwarding state
Fri Oct 20 19:52:10 CST 2017 boot_check[5582]: INFO: Wireless OK
[ 37.020000] ctf: bytes_threshold 3MB(3145728B), mask F00000, old_mark: 200000, new_mark: 400000
[ 45.660000] system bringup check is okay.
rcS S boot: INFO: rcS S boot timing 39 seconds.
Fri Oct 20 19:52:31 CST 2017 INFO: rcS S boot timing 39 seconds.
rcS S boot: system type(R2D/1): SATA/3
Fri Oct 20 19:52:31 CST 2017 system type(R2D/1): SATA/3
rcS S boot: ROOTFS: /dev/ubi1_0 on / type ubifs (ro,noatime,bulk_read,no_chk_data_crc,compr=none)
Fri Oct 20 19:52:31 CST 2017 ROOTFS: /dev/ubi1_0 on / type ubifs (ro,noatime,bulk_read,no_chk_data_crc,compr=none)
Fri Oct 20 19:52:32 CST 2017 boot_check[8610]: Booting up finished.
|
|