AC9电信定制版编程器备份 RTL8197FS+RTL8367RB

绝***

16MROM  64MRAM

配置和AC10和AC10U一样 可以刷国外的AC10完整固件

附上ttl启动信息

Booting...
init_ram
00000102 W init ddr ok

DRAM Type: DDR2
        DRAM frequency: 400MHz
        DRAM Size: 64MB
JEDEC id C84018, EXT id 0xc840
found gd25q128
flash vendor: GigaDevice
gd25q128, size=16MB, erasesize=64KB, max_speed_hz=75000000Hz
auto_mode=0 addr_width=3 erase_opcode=0x000000d8
=>CPU Wake-up interrupt happen! GISR=89000004

---Realtek RTL8197F boot code at 2017.08.26-09:26+0800 v3.4.11B.9 (999MHz)
Mac addr:04-95-e6-59-92-40
lan_wan_isolation Initing...
config: lan port mask is 0x000000fe
config: wan port mask is 0x000000e1
lan_wan_isolation Initing has been completed.
lan_wan_isolation Initing...
config: lan port mask is 0x000000fe
config: wan port mask is 0x000000e1
lan_wan_isolation Initing has been completed.
Off usb led
Off usb led
wait for upgrage
port[0] link:down
port[1] link:down
port[2] link:down
port[3] link:down
port[4] link:down
irq:0x00008080
Jump to image start=0x80a00000...
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
start address: 0x8049b930
Linux version 3.10.90 (root@linux-aj0z) (gcc version 4.4.7 (Realtek MSDK-4.4.7 Build 2001) ) #6 Sat Jan 27 15:58:26 CST 2018
bootconsole [early0] enabled
CPU revision is: 00019385 (MIPS 24Kc)
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone ranges:
  Normal   [mem 0x00000000-0x03ffffff]
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x00000000-0x03ffffff]
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock4
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Writing ErrCtl register=0005fae4
Readback ErrCtl register=0005fae4
Memory: 41024k/65536k available (4739k kernel code, 24512k reserved, 2345k data, 208k init, 0k highmem)




分区信息
loop: module loaded
m25p80 spi0.0: change speed to 15000000Hz, div 7
JEDEC id C84018
m25p80 spi0.0: found gd25q128, expected m25p80
flash vendor: GigaDevice
m25p80 spi0.0: gd25q128 (16384 Kbytes) (25000000 Hz)
m25p80 spi0.0: change speed to 25000000Hz, div 4
Kernel code size:0x225c12
7 rtkxxpart partitions found on MTD device m25p80
Creating 7 MTD partitions on "m25p80":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000020000 : "Bootloader"
0x000000020000-0x000000030000 : "CFG"
0x000000030000-0x0000007e0000 : "KernelFS"
0x000000255c12-0x0000007e0000 : "RootFS"
0x0000007e0000-0x0000007f0000 : "CFM"
0x0000007f0000-0x000000800000 : "CFM_BACKUP"


长按复位开机进boot模式可以tftp上传固件给boot loader  ip地址192.168.1.6 没有web页面
配置和360P4C一样 如果有P4C的备份固件就好了

游客，如果您要查看本帖隐藏内容请回复

bul***

这有什么用？能kexue上网吗？

jsnt***

感谢分享！ 坑爹的螃蟹芯

533***

螃蟹芯又出64M版了吗  缩得真狠

gz***

感谢分享！

nianq***

文件已经取消了 能再分享一下吗

wan***

文件已经取消了 能再分享一下吗

绝***

wang517 发表于 2019-7-15 20:04
文件已经取消了 能再分享一下吗

链接：https://pan.baidu.com/s/1IfuhygnfxS5ubDkf3jXRIg
提取码：l5ic

wan***

绝绝 发表于 2019-9-25 10:15
链接：https://pan.baidu.com/s/1IfuhygnfxS5ubDkf3jXRIg
提取码：l5ic

非常感谢，救活了我的机器。

hao***

怎么修改MAC啊？有会的吗。

afe***

有gpl源代码，自己编译固件

chenti***

链接失效...

diluxi***

Ac10有好几个版本，具体什么版本啊，电源有12v1a，9v0.85a

微***

afeng11 发表于 2020-12-14 19:27
有gpl源代码，自己编译固件

GPL代码您那还保存有吗? 可以分享一份给我吗? 谢谢您了!

afe***

微启宇 发表于 2022-7-19 01:34
GPL代码您那还保存有吗? 可以分享一份给我吗? 谢谢您了!

github上面搜索RTL8197，一大堆