求救，B70开root权限

cly***

本帖最后由 cly202 于 2020-12-31 17:02 编辑

求救，现在极路由APP服务器被关，连不上服务器，无法申请开发者模式，云平台也没法使用了，无法下载安装插件，请高手指一条明路，如何开root权限啊？
已经用TTL连接，可是不知道怎么中断，请大佬帮忙指导，一下是TTL加载信息：

U-Boot 1.1.3 (Nov 8 2016 - 02:34:36)
Board: Ralink APSoC DRAM: 256 MB
mtest end addr: 8fe79f88
relocate_code Pointer at: 8ff9c000
Config XHCI 40M PLL
Allocate 16 byte aligned buffer: 8ffe0310
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C8 D1 80 95 40]
Device not found, ID: c8d1
Not Support this Device!
chip_mode=00000001
Support this Device in MTK table! c8d1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
.*** Warning - bad CRC, using default environment
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
#Reset_MT7530
set LAN/WAN LLLLW 0
firmware_backup is equal to firmware!
=================================================
Check firmware :
Header Magic Number --> OK
Header Checksum --> OK
Data Checksum --> ......................OK
MD5 Header Magic Number --> OK
MD5 Header CRC --> OK
MD5 Firmware md5 --> ..............................................................................................................................................................................OK
=================================================
firmware: check ok!
3: System Boot system code via Flash.
## Booting image at bc140000 ...
Image Name: HC5962
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1442340 Bytes = 1.4 MB
Load Address: 81001000
Entry Point: 81001000
...................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 81001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (build@DEV-9-1-242) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 1.4.8.20462s) ) #1 SMP Thu Dec 21 01:52:40 CST 2017
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 880 MHz
[ 0.000000] GCMP present
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x0fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x0fffffff]
[ 0.000000] Detected 3 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @8166b000 s6976 r8192 d13504 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: board=HC5962 console=ttyS1,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00000481
[ 0.000000] Readback ErrCtl register=00000481
[ 0.000000] allocated 524288 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 254708k/262144k available (3267k kernel code, 7436k reserved, 702k data, 248k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU debugfs-based tracing is enabled.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled
[ 0.130000] Calibrating delay loop... 577.53 BogoMIPS (lpj=2887680)
[ 0.190000] pid_max: default: 32768 minimum: 301
[ 0.190000] Mount-cache hash table entries: 512
[ 0.200000] Initializing cgroup subsys memory
[ 0.200000] Initializing cgroup subsys devices
[ 0.200000] Initializing cgroup subsys net_cls
[ 0.210000] Initializing cgroup subsys blkio
[ 0.210000] Initializing cgroup subsys net_prio
[ 0.220000] launch: starting cpu1
[ 0.220000] launch: cpu1 gone!
[ 0.220000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.220000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.220000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.220000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.280000] Synchronize counters for CPU 1: done.
[ 0.290000] launch: starting cpu2
[ 0.290000] launch: cpu2 gone!
[ 0.290000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.290000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.290000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.290000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.350000] Synchronize counters for CPU 2: done.
[ 0.360000] launch: starting cpu3
[ 0.360000] launch: cpu3 gone!
[ 0.360000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.360000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.360000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.360000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.420000] Synchronize counters for CPU 3: done.
[ 0.430000] Brought up 4 CPUs
[ 0.430000] NET: Registered protocol family 16
[ 0.440000] MIPS: machine is HiWiFi Wireless HC5962 Board
[ 0.740000] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.740000] PCIE PHY initialize
[ 0.750000] ***** Xtal 40MHz *****
[ 0.750000] start MT7621 PCIe register access
[ 1.340000] RALINK_RSTCTRL = 7000000
[ 1.350000] RALINK_CLKCFG1 = 77ffeff8
[ 1.350000]
[ 1.350000] *************** MT7621 PCIe RC mode *************
[ 1.850000] PCIE2 no card, disable it(RST&CLK)
[ 1.850000] pcie_link status = 0x3
[ 1.860000] RALINK_RSTCTRL= 3000000
[ 1.860000] *** Configure Device number setting of Virtual PCI-PCI bridge ***
[ 1.870000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
[ 1.870000] PCIE0 enabled
[ 1.870000] PCIE1 enabled
[ 1.880000] interrupt enable status: 300000
[ 1.880000] Port 1 N_FTS = 1b105000
[ 1.880000] Port 0 N_FTS = 1b105000
[ 1.890000] config reg done
[ 1.890000] init_rt2880pci done
[ 1.900000] bio: create slab <bio-0> at 0
[ 1.900000] PCI host bridge to bus 0000:00
[ 1.910000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.910000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.920000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.920000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.930000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.930000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.940000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.940000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.950000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 1.950000] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
[ 1.960000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 1.960000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 1.970000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 1.970000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.980000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.980000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 1.990000] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
[ 1.990000] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.000000] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.000000] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff pref]
[ 2.010000] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
[ 2.010000] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
[ 2.020000] BAR0 at slot 0 = 0
[ 2.020000] bus=0x0, slot = 0x0
[ 2.020000] BAR0 at slot 1 = 0
[ 2.020000] bus=0x0, slot = 0x1
[ 2.030000] bus=0x1, slot = 0x0, irq=0x4
[ 2.030000] bus=0x2, slot = 0x1, irq=0x18
[ 2.030000] Switching to clocksource MIPS
[ 2.040000] NET: Registered protocol family 2
[ 2.040000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.050000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.070000] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.070000] TCP: reno registered
[ 2.080000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.080000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.090000] NET: Registered protocol family 1
[ 2.320000] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.330000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.340000] msgmni has been set to 497
[ 2.340000] io scheduler noop registered
[ 2.350000] io scheduler deadline registered (default)
[ 2.350000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 2.360000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
[ 2.370000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
[ 2.380000] brd: module loaded
[ 2.390000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.390000] Allocate 16 byte aligned buffer: 8145be90
[ 2.400000] Enable NFI Clock
[ 2.400000] # MTK NAND # : Use HW ECC
[ 2.400000] NAND ID [C8 D1 80 95 40, 00809540]
[ 2.410000] Device found in MTK table, ID: c8d1, EXT_ID: 809540
[ 2.420000] Support this Device in MTK table! c8d1
[ 2.420000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (Unknown NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[ 2.430000] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.440000] Scanning device for bad blocks
[ 2.590000] Signature matched and data read!
[ 2.590000] load_fact_bbt success 1023
[ 2.600000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.610000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.620000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.620000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.630000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.640000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.650000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.660000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.670000] Creating 11 MTD partitions on "MT7621-NAND":
[ 2.680000] 0x000000000000-0x000000080000 : "u-boot"
[ 2.690000] 0x000000080000-0x000000100000 : "debug"
[ 2.690000] 0x000000100000-0x000000140000 : "Factory"
[ 2.700000] 0x000000140000-0x000002140000 : "firmware"
[ 2.710000] 2 uimage-fw partitions found on MTD device firmware
[ 2.710000] 0x000000140000-0x0000002c0000 : "kernel"
[ 2.720000] 0x0000002c0000-0x000002140000 : "rootfs"
[ 2.730000] mtd: device 5 (rootfs) set to be root filesystem
[ 2.730000] 0x000002140000-0x0000021c0000 : "hw_panic"
[ 2.740000] 0x0000021c0000-0x000002240000 : "bdinfo"
[ 2.780000] 0x000002240000-0x0000022c0000 : "backup"
[ 2.790000] 0x0000022c0000-0x0000032c0000 : "overlay"
[ 2.790000] 0x0000032c0000-0x0000052c0000 : "firmware_backup"
[ 2.800000] 0x0000052c0000-0x0000054c0000 : "oem"
[ 2.810000] 0x0000054c0000-0x000007f80000 : "opt"
[ 2.810000] [mtk_nand] probe successfully!
[ 2.820000] GMAC1_MAC_ADRH -- : 0x0000d4ee
[ 2.820000] GMAC1_MAC_ADRL -- : 0x07543260
[ 2.830000] PROC INIT OK!
[ 2.830000] Ralink APSoC Hardware Watchdog Timer
[ 2.840000] TCP: cubic registered
[ 2.840000] NET: Registered protocol family 17
[ 2.840000] 8021q: 802.1Q VLAN Support v1.8
[ 2.850000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 2.860000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.870000] Freeing unused kernel memory: 248K (813e2000 - 81420000)
procd: Console is alive
[ 5.240000] usbcore: registered new interface driver usbfs
[ 5.240000] usbcore: registered new interface driver hub
[ 5.250000] usbcore: registered new device driver usb
[ 5.290000] SCSI subsystem initialized
procd: - preinit -
[ 6.280000] boot from nand
[ 6.400000] UBI: attaching mtd9 to ubi0
[ 6.550000] UBI: scanning is finished
[ 6.570000] UBI: attached mtd9 (name "overlay", size 16 MiB) to ubi0
[ 6.570000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 6.580000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 6.590000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 6.590000] UBI: good PEBs: 128, bad PEBs: 0, corrupted PEBs: 0
[ 6.600000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 6.610000] UBI: max/mean erase counter: 402/238, WL threshold: 4096, image sequence number: 82760497
[ 6.610000] UBI: available PEBs: 0, total reserved PEBs: 128, PEBs reserved for bad PEB handling: 20
[ 6.620000] UBI: background thread "ubi_bgt0d" started, PID 316
UBI device number 0, total 128 LEBs (16252928 bytes, 15.5 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 6.700000] UBIFS: background thread "ubifs_bgt0_0" started, PID 338
[ 6.770000] UBIFS: recovery needed
[ 7.060000] UBIFS: recovery completed
[ 7.070000] UBIFS: mounted UBI device 0, volume 0, name "overlay"
[ 7.070000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 7.080000] UBIFS: FS size: 11935744 bytes (11 MiB, 94 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 7.090000] UBIFS: reserved for root: 563754 bytes (550 KiB)
[ 7.100000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2A66EA76-16D5-4645-A99E-1189A394EE8C, small LPT model
mounting /dev/root
procd: - early -
procd: - ubus -
procd: - init -
[ 8.490000] NET: Registered protocol family 10
[ 8.820000] MT7603E module init
[ 8.830000] MT7603E AP Driver version-4.0.1.0rev2.P1
[ 9.660000] MT7612E module init
[ 9.670000] MT76x2 AP Driver version-3.0.4.0.P2.20160308
[ 10.580000] Initializing XFRM netlink socket
[ 10.590000] NET: Registered protocol family 15
[ 10.610000] loop: module loaded
[ 10.610000] tun: Universal TUN/TAP device driver, 1.6
[ 10.620000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 10.650000] l2tp_core: L2TP core driver, V2.0
[ 10.660000] l2tp_netlink: L2TP netlink interface
[ 10.670000] sit: IPv6 over IPv4 tunneling driver
[ 10.680000] exFAT: Version 1.2.9
[ 10.680000] gre: GRE over IPv4 demultiplexor driver
[ 10.690000] ip_gre: GRE over IPv4 tunneling driver
[ 10.700000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.710000] ehci-platform: EHCI generic platform driver
[ 10.750000] nf_conntrack version 0.5.0 (3983 buckets, 15932 max)
[ 10.760000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.770000] Netfilter messages via NETLINK v0.30.
[ 10.780000] ip_set: protocol 6
[ 10.820000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.830000] ***Module syslog inserted(log_addr:8d04c000)***
[ 10.840000] *****run project phy.
[ 10.870000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 10.890000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 10.910000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 10.930000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 10.950000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 10.970000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 10.990000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.020000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.040000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.070000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.150000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.180000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.210000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.230000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.250000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.280000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.310000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.330000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.350000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.380000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.550000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 11.550000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
[ 11.560000] xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000
[ 11.570000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 11.570000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.580000] usb usb1: Product: xHCI Host Controller
[ 11.580000] usb usb1: Manufacturer: Linux 3.10.49 xhci-hcd
[ 11.590000] usb usb1: SerialNumber: xhci-hcd
[ 11.600000] hub 1-0:1.0: USB hub found
[ 11.600000] hub 1-0:1.0: 2 ports detected
[ 11.600000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 11.610000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
[ 11.620000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 11.620000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.630000] usb usb2: Product: xHCI Host Controller
[ 11.640000] usb usb2: Manufacturer: Linux 3.10.49 xhci-hcd
[ 11.640000] usb usb2: SerialNumber: xhci-hcd
[ 11.650000] hub 2-0:1.0: USB hub found
[ 11.650000] hub 2-0:1.0: 1 port detected
[ 11.660000] i2c-gpio i2c-gpio.0: using pins 3 (SDA) and 4 (SCL)
[ 11.680000] u32 classifier
[ 11.690000] input device check on
[ 11.690000] Actions configured
[ 11.700000] Mirror/redirect action on
[ 11.700000] Failed to load ipt action
[ 11.730000] fuse init (API version 7.22)
[ 11.750000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.870000] ctnetlink v0.93: registering with nfnetlink.
[ 12.890000] rtc-pt7c4338 0-0068: rtc core: registered pt7c4338 as rtc0
[ 12.900000] usbcore: registered new interface driver usb-storage
[ 12.950000] xt_time: kernel timezone is -0000
[ 12.970000] PPP generic driver version 2.4.2
[ 12.970000] PPP MPPE Compression module registered
[ 12.980000] NET: Registered protocol family 24
[ 12.990000] p p t p driver version 0.8.5
[ 13.000000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 14.560000] oem: use pcba GM2101v01
Jan 1 08:04:46 Hiwifi syslog.info syslogd started: BusyBox v1.22.1
Jan 1 08:04:46 Hiwifi kern.notice kernel: klogd started: BusyBox v1.22.1 (2017-12-21 01:33:16 CST)
Jan 1 08:04:46 Hiwifi kern.notice kernel: [ 0.000000] Linux version 3.10.49 (build@DEV-9-1-242) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 1.4.8.20462s) ) #1 SMP Thu Dec 21 01:52:40 CST 2017
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000]
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] The CPU feqenuce set to 880 MHz
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] GCMP present
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Software DMA cache coherency
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Determined physical RAM map:
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] memory: 10000000 @ 00000000 (usable)
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Zone ranges:
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] DMA [mem 0x00000000-0x00ffffff]
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Normal [mem 0x01000000-0x0fffffff]
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Movable zone start for each node
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Early memory node ranges
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] node 0: [mem 0x00000000-0x0fffffff]
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] On node 0 totalpages: 65536
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 813ca180, node_mem_map 81468000
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] DMA zone: 32 pages used for memmap
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] DMA zone: 0 pages reserved
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] DMA zone: 4096 pages, LIFO batch:0
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] Normal zone: 480 pages used for memmap
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] Normal zone: 61440 pages, LIFO batch:15
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Detected 3 available secondary CPU(s)
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] PERCPU: Embedded 7 pages/cpu @8166b000 s6976 r8192 d13504 u32768
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] pcpu-alloc: s6976 r8192 d13504 u32768 alloc=8*4096
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Jan 1 08:04:46 Hiwifi kern.notice kernel: [ 0.000000] Kernel command line: board=HC5962 console=ttyS1,115200 rootfstype=squashfs,jffs2
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Writing ErrCtl register=00000481
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Readback ErrCtl register=00000481
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] allocated 524288 bytes of page_cgroup
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Memory: 254708k/262144k available (3267k kernel code, 7436k reservJan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Hiwifi syslog.info logfwd[1324]: [output tcp] <log_server> Use default 1024 for "buff_limit"
Jan 1 08:04:46 Hiwifi syslog.info logfwd[1325]: === logfwd 4.2.3 Start ===
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: lanport [0]: 1
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: lanport [1]: 2
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: lanport [2]: 3
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: wanport: 4
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: wan dev: eth2
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: lan dev: eth2
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: binfo name: HC5962
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: binfo type: router
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: sinfo type: NULL
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: sinfo minsize: 0M
Jan 1 08:04:47 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:47 Hiwifi user.emerg syslog: ---stop ---
Jan 1 08:04:47 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:47 Hiwifi user.emerg syslog: no /usr/sbin/storaged2 found; none killed
Jan 1 08:04:47 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:47 Hiwifi user.emerg syslog: storaged2:
Jan 1 08:04:47 Hiwifi user.emerg syslog: ---start---
Jan 1 08:04:47 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:47 Hiwifi user.notice /init.d/storaged2: <1394> /init.d/storaged2 boot
Jan 1 08:04:47 Hiwifi user.emerg syslog: storaged2:
Jan 1 08:04:47 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:48 Hiwifi user.warn wpad[1443]: uci reload success
Jan 1 08:04:48 Hiwifi user.warn wpad[1443]: router is master, macaddr: D4:EE:07:54:32:60
Jan 1 08:04:48 Hiwifi user.warn wpad[1443]: wlog_init
[ 18.640000] [NOTICE] <XT_TIME_CONF> (time_conf_init:140) xt_timc_conf module init
Jan 1 08:04:49 Hiwifi kern.warn kernel: [ 18.640000] [NOTICE] <XT_TIME_CONF> (time_conf_init:140) xt_timc_conf module init
Jan 1 08:04:49 Hiwifi user.notice firewall: Error: Failed to connect to ubus
Jan 1 08:04:49 Hiwifi user.notice wireless: procd[1]-->S20network[1525]-->wifi down
Jan 1 08:04:49 Hiwifi user.emerg syslog: wireless: procd[1]-->S20network[1525]-->wifi down
Jan 1 08:04:49 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:50 Hiwifi user.warn wpad[1443]: uci reload success
Jan 1 08:04:50 Hiwifi user.warn wpad[1443]: himsg_handle_wireless_down radio0
Jan 1 08:04:50 Hiwifi user.warn wpad[1443]: uci reload success
Jan 1 08:04:50 Hiwifi user.warn wpad[1443]: himsg_handle_wireless_down radio1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: netifd_ubus_init:1180: connected as c9d060e8
[ 19.570000] MT7530 Reset Completed!!
Jan 1 08:04:50 [ 19.580000] phy_free_head is 0xc54000!!!
Hiwifi kern.warn[ 19.580000] phy_free_tail_phy is 0xc55ff0!!!
kernel: [ 19.[ 19.590000] txd_pool=a0c58000 phy_txd_pool=00C58000
570000] MT7530 R[ 19.590000] ei_local->skb_free start address is 0x8faa26c4.
eset Completed!![ 19.600000] free_txd: 00c58010, ei_local->cpu_ptr: 00C58000
Jan 1 08:04:5[ 19.610000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
0 Hiwifi kern.wa[ 19.610000] ----------------+---------+--------
rn kernel: [ 1[ 19.620000] 0xa0c58000 0x00C58000 0x00C58000
9.580000] phy_fr[ 19.630000]
[ 19.630000] phy_qrx_ring = 0x00c56000, qrx_ring = 0xa0c56000
ee_head is 0xc54000!!!
Jan 1 0[ 19.640000]
[ 19.640000] phy_rx_ring0 = 0x00c60000, rx_ring0 = 0xa0c60000
8:04:50 Hiwifi k[ 19.640000] GMAC1_MAC_ADRH -- : 0x0000d4ee
ern.warn kernel:[ 19.650000] GMAC1_MAC_ADRL -- : 0x07543260
[ 19.580000] [ 19.660000] GDMA2_MAC_ADRH -- : 0x0000d4ee
phy_free_tail_ph[ 19.660000] GDMA2_MAC_ADRL -- : 0x07543261
y is 0xc55ff0!!!
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.590000] txd_pool=a0c58000 phy_txd_pool=00C58000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.590000] ei_local->skb_free start address is 0x8faa26c4.
Jan 1 08:04:50 Hiwifi daemon.debug netifd: proto_shell_add_handler:828: Add handler for script ./dhcp.sh: dhcp
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.600000] free_txd: 00c58010, ei_local->cpu_ptr: 00C58000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.610000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.610000] ----------------+---------+--------
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.620000] 0xa0c58000 0x00C58000 0x00C58000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.630000]
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.630000] phy_qrx_ring = 0x00c56000, qrx_ring = 0xa0c56000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.640000]
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.640000] phy_rx_ring0 = 0x00c60000, rx_ring0 = 0xa0c60000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.640000] GMAC1_MAC_ADRH -- : 0x0000d4ee
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.650000] GMAC1_MAC_ADRL -- : 0x07543260
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.660000] GDMA2_MAC_ADRH -- : 0x0000d4ee
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.660000] GDMA2_MAC_ADRL -- : 0x07543261
Jan 1 08:04:50 Hiwifi daemon.debug netifd: proto_shell_add_handler:828: Add handler for script ./l2tp.sh: l2tp
Jan 1 08:04:50 Hiwifi daemon.debug netifd: proto_shell_add_handler:828: Add handler for script ./ppp.sh: ppp
Jan 1 08:04:50 Hiwifi daemon.debug netifd: proto_shell_add_handler:828: Add handler for script ./ppp.sh: pppoe
Jan 1 08:04:50 Hiwifi user.notice wireless: procd[1]-->S20network[1525]-->wifi
Jan 1 08:04:50 Hiwifi user.emerg syslog: wireless: procd[1]-->S20network[1525]-->wifi
Jan 1 08:04:50 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:50 Hiwifi daemon.debug netifd: proto_shell_add_handler:828: Add ha[ 19.900000] ra2880stop()...ndler for scriptDone
./ppp.sh: p p t p
Jan 1 08:04:50 Hiwifi daemon.d[ 19.900000] Free TX/RX Ring Memory!
ebug netifd: interface_update:1077: Create interface 'loopback'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_create_default:313: Create simple device 'lo'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_init_virtual:278: Initialize device 'lo'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_set_present:402: Network device 'lo' is now present
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'lo', refcount=1
J[ 19.950000] MT7530 Reset Completed!!
an 1 08:04:50 Hiwifi daemon.debug netifd: interface_set_available:359: Interface 'loopback', available=1
Jan 1 08:04:50 Hiwif[ 19.960000] phy_free_head is 0xc54000!!!
i daemon.debug n[ 19.970000] phy_free_tail_phy is 0xc55ff0!!!
etifd: device_ad[ 19.970000] txd_pool=a0c58000 phy_txd_pool=00C58000
d_user:462: Add [ 19.980000] ei_local->skb_free start address is 0x8faa26c4.
user for device [ 19.990000] free_txd: 00c58010, ei_local->cpu_ptr: 00C58000
'lo', refcount=2[ 19.990000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
Jan 1 08:04:5[ 20.000000] ----------------+---------+--------
0 Hiwifi daemon.[ 20.010000] 0xa0c58000 0x00C58000 0x00C58000
debug netifd: de[ 20.010000]
[ 20.010000] phy_qrx_ring = 0x00c56000, qrx_ring = 0xa0c56000
vice_create:660: Create new devi[ 20.020000]
[ 20.020000] phy_rx_ring0 = 0x00c60000, rx_ring0 = 0xa0c60000
ce 'br-lan' (Bri[ 20.030000] GMAC1_MAC_ADRH -- : 0x0000d4ee
dge)
Jan 1 08:[ 20.040000] GMAC1_MAC_ADRL -- : 0x07543260
04:50 Hiwifi daemon.debug netifd: device_init_vi[ 20.040000] device eth2 entered promiscuous mode
rtual:278: Initialize device 'br-lan'
Jan 1 08[ 20.050000] br-lan: port 1(eth2) entered forwarding state
:04:50 Hiwifi da[ 20.060000] br-lan: port 1(eth2) entered forwarding state
emon.debug netifd: interface_update:1077: Create interface 'lan'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for [ 20.080000] ethernet:eth3 up
device 'br-lan', refcount=1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'br-lan', refcount=2
Jan 1 08:04:50 Hiwifi daemon.debug netifd: interface_update:1077: Create interface 'wan'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_create_default:313: Create simple device 'eth3'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_init_virtual:278: Initialize device 'eth3'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_set_present:402: Network device 'eth3' is now present
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'eth3', refcount=1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: interface_set_available:359: Interface 'wan', available=1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'eth3', refcount=2
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_create:660: Create new device 'br-lan1' (Bridge)
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_init_virtual:278: Initialize device 'br-lan1'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: interface_update:1077: Create interface 'lan1'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'br-lan1', refcount=1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'br-lan1', refcount=2
Jan 1 08:04:50 Hiwifi daemon.debug netifd: cb_clear_event:579: Remove a rule
Jan 1 08:04:50 Hiwifi daemon.debug netifd: config_init_wireless:362: device radio0 not found!
Jan 1 08:04:50 Hiwifi daemon.debug netifd: config_init_wireless:362: device radio1 not found!
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_create_default:313: Create simple device 'eth2'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_init_virtual:278: Initialize device 'eth2'
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.900000] ra2880stop()...Done
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.900000] Free TX/RX Ring Memory!
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_set_present:402: Network device 'eth2' is now present
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'eth2', refcount=1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_set_present:402: Bridge 'br-lan' is now present
Jan 1 08:04:50 Hiwifi daemon.debug netifd: interface_set_available:359: Interface 'lan', available=1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_claim:224: Claim Bridge br-lan, new active count: 1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_claim:224: Claim Network device eth2, new active count: 1
Jan 1 08:04:50 Hiwifi user.notice /init.d/storaged2: <1394> recover_info ----
Jan 1 08:04:50 Hiwifi user.info syslog: pid(1412):error:wait_data_available:40:select fd 3 failed, rc=-1 errno=4
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.950000] MT7530 Reset Completed!!
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.960000] phy_free_head is 0xc54000!!!
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.970000] phy_free_tail_phy is 0xc55ff0!!!
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.970000] txd_pool=a0c58000 phy_txd_pool=00C58000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.980000] ei_local->skb_free start address is 0x8faa26c4.
Jan 1 08:04:50 Hiwifi user.notice /init.d/storaged2: <1394> uci get hiwifi.storage.data_uuid=
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.990000] f[ 20.370000] device ra0 entered promiscuous mode
ree_txd: 00c5801[ 20.380000] br-lan: port 2(ra0) entered forwarding state
0, ei_local->cpu[ 20.390000] br-lan: port 2(ra0) entered forwarding state
_ptr: 00C58000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.990000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 20.000000] ----------------+---------+--------
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 20.010000] 0xa0c58000 0x00C58000 0x00C58000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 20.01000Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 20.Jan 1 08:04:50 Jan 1 08:04:50 Hiwifi user.notice /init.d/storaJan 1 08:04:50 Jan 1 08:04:50 Hiwifi kern.info kernel: [ 20.Jan 1 08:04:50 Jan 1 08:04:50 Jan 1 08:04:50 Jan 1 08:04:50 Jan 1 08:04:50 Hiwifi daemon.debug netifd: get_Jan 1 08:04:50 Jan 1 08:04:50 Jan 1 08:04:50 Jan 1 08:04:50 Hiwifi kern.warnJan 1 08:04:50 Hiwifi daemon.notice netifd: wan (1759): udhcpc (v1.22.1) started
Jan 1 08:04:50 Hiwifi user.warn wpad[1443]: uci reload success
Jan 1 08:04:50 Hiwifi user.warn wpad[1443]: himsg_handle_wireless_down radio1
Jan 1 08:04:51 Hiwifi user.notice switch: reset switch(lan)
Jan 1 08:04:51 Hiwifi user.warn wpad[1443]: uci reload success
Jan 1 08:04:51 Hiwifi user.warn wpad[1443]: himsg_handle_wireless_up radio0
Jan 1 08:04:51 Hiwifi user.warn wpad[1443]: up interface ra0
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_create_default:313: Create simple device 'ra0'
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_init_virtual:278: Initialize device 'ra0'
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_set_present:402: Network device 'ra0' is now present
Jan 1 08:04:51 Hiwifi daemon.notice netifd: Network device 'ra0' link is up
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'ra0', refcount=1
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_claim:224: Claim Network device ra0, new active count: 1
Jan 1 08:04:51 Hiwifi kern.info kernel: [ 20.370000] device ra0 entered promiscuous mode
Jan 1 08:04:51 Hiwifi kern.info kernel: [ 20.380000] br-lan: port 2(ra0) entered forwarding state
Jan 1 08:04:51 Hiwifi kern.info kernel: [ 20.390000] br-lan: port 2(ra0) entered forwarding state
Jan 1 08:04:51 Hiwifi user.notice capshd_slave: udhcpc event received: deconfig
Jan 1 08:04:51 Hiwifi daemon.notice netifd: wan (1759): Sending discover...
Jan 1 08:04:51 Hiwifi user.notice ifup: Enabling Router Solicitations on lan (br-lan)
[ 21.010000] device rai0 entered promiscuous modeload success

复制代码

xym***

暂时没法了

linu***

没有ROOT权限，想刷机都困难了。

cly***

大虾，还有救不？

wangyu***

拆机，接ttl，中断刷breed

cly***

wangyuddd000 发表于 2020-12-30 18:14
拆机，接ttl，中断刷breed

元旦节试试看

shiju***

实在不行就上编程器，先备份，再刷breed

爱宰***

同求，服务器都关了。

恩山***

同求，谢谢

恩山***

同求，谢谢

cly***

接了TTL，可是Putty显示一直停不下来啊（见附图），感觉是在不断重试，请问要怎么弄啊？小白一枚，见笑了！

cly***

请大佬帮忙分析下要如何中断啊？以下是TTL加载过程：

U-Boot 1.1.3 (Nov 8 2016 - 02:34:36)
Board: Ralink APSoC DRAM: 256 MB
mtest end addr: 8fe79f88
relocate_code Pointer at: 8ff9c000
Config XHCI 40M PLL
Allocate 16 byte aligned buffer: 8ffe0310
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C8 D1 80 95 40]
Device not found, ID: c8d1
Not Support this Device!
chip_mode=00000001
Support this Device in MTK table! c8d1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
.*** Warning - bad CRC, using default environment
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
#Reset_MT7530
set LAN/WAN LLLLW 0
firmware_backup is equal to firmware!
=================================================
Check firmware :
Header Magic Number --> OK
Header Checksum --> OK
Data Checksum --> ......................OK
MD5 Header Magic Number --> OK
MD5 Header CRC --> OK
MD5 Firmware md5 --> ..............................................................................................................................................................................OK
=================================================
firmware: check ok!
3: System Boot system code via Flash.
## Booting image at bc140000 ...
Image Name: HC5962
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1442340 Bytes = 1.4 MB
Load Address: 81001000
Entry Point: 81001000
...................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 81001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (build@DEV-9-1-242) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 1.4.8.20462s) ) #1 SMP Thu Dec 21 01:52:40 CST 2017
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 880 MHz
[ 0.000000] GCMP present
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 [url=home.php?mod=space&uid=162986]@[/url] 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x0fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x0fffffff]
[ 0.000000] Detected 3 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @8166b000 s6976 r8192 d13504 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: board=HC5962 console=ttyS1,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00000481
[ 0.000000] Readback ErrCtl register=00000481
[ 0.000000] allocated 524288 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 254708k/262144k available (3267k kernel code, 7436k reserved, 702k data, 248k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU debugfs-based tracing is enabled.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled
[ 0.130000] Calibrating delay loop... 577.53 BogoMIPS (lpj=2887680)
[ 0.190000] pid_max: default: 32768 minimum: 301
[ 0.190000] Mount-cache hash table entries: 512
[ 0.200000] Initializing cgroup subsys memory
[ 0.200000] Initializing cgroup subsys devices
[ 0.200000] Initializing cgroup subsys net_cls
[ 0.210000] Initializing cgroup subsys blkio
[ 0.210000] Initializing cgroup subsys net_prio
[ 0.220000] launch: starting cpu1
[ 0.220000] launch: cpu1 gone!
[ 0.220000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.220000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.220000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.220000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.280000] Synchronize counters for CPU 1: done.
[ 0.290000] launch: starting cpu2
[ 0.290000] launch: cpu2 gone!
[ 0.290000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.290000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.290000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.290000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.350000] Synchronize counters for CPU 2: done.
[ 0.360000] launch: starting cpu3
[ 0.360000] launch: cpu3 gone!
[ 0.360000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.360000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.360000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.360000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.420000] Synchronize counters for CPU 3: done.
[ 0.430000] Brought up 4 CPUs
[ 0.430000] NET: Registered protocol family 16
[ 0.440000] MIPS: machine is HiWiFi Wireless HC5962 Board
[ 0.740000] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.740000] PCIE PHY initialize
[ 0.750000] ***** Xtal 40MHz *****
[ 0.750000] start MT7621 PCIe register access
[ 1.340000] RALINK_RSTCTRL = 7000000
[ 1.350000] RALINK_CLKCFG1 = 77ffeff8
[ 1.350000]
[ 1.350000] *************** MT7621 PCIe RC mode *************
[ 1.850000] PCIE2 no card, disable it(RST&CLK)
[ 1.850000] pcie_link status = 0x3
[ 1.860000] RALINK_RSTCTRL= 3000000
[ 1.860000] *** Configure Device number setting of Virtual PCI-PCI bridge ***
[ 1.870000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
[ 1.870000] PCIE0 enabled
[ 1.870000] PCIE1 enabled
[ 1.880000] interrupt enable status: 300000
[ 1.880000] Port 1 N_FTS = 1b105000
[ 1.880000] Port 0 N_FTS = 1b105000
[ 1.890000] config reg done
[ 1.890000] init_rt2880pci done
[ 1.900000] bio: create slab <bio-0> at 0
[ 1.900000] PCI host bridge to bus 0000:00
[ 1.910000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.910000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.920000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.920000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.930000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.930000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.940000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.940000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.950000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 1.950000] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
[ 1.960000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 1.960000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 1.970000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 1.970000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.980000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.980000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 1.990000] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
[ 1.990000] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.000000] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.000000] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff pref]
[ 2.010000] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
[ 2.010000] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
[ 2.020000] BAR0 at slot 0 = 0
[ 2.020000] bus=0x0, slot = 0x0
[ 2.020000] BAR0 at slot 1 = 0
[ 2.020000] bus=0x0, slot = 0x1
[ 2.030000] bus=0x1, slot = 0x0, irq=0x4
[ 2.030000] bus=0x2, slot = 0x1, irq=0x18
[ 2.030000] Switching to clocksource MIPS
[ 2.040000] NET: Registered protocol family 2
[ 2.040000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.050000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.070000] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.070000] TCP: reno registered
[ 2.080000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.080000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.090000] NET: Registered protocol family 1
[ 2.320000] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.330000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.340000] msgmni has been set to 497
[ 2.340000] io scheduler noop registered
[ 2.350000] io scheduler deadline registered (default)
[ 2.350000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 2.360000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
[ 2.370000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
[ 2.380000] brd: module loaded
[ 2.390000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.390000] Allocate 16 byte aligned buffer: 8145be90
[ 2.400000] Enable NFI Clock
[ 2.400000] # MTK NAND # : Use HW ECC
[ 2.400000] NAND ID [C8 D1 80 95 40, 00809540]
[ 2.410000] Device found in MTK table, ID: c8d1, EXT_ID: 809540
[ 2.420000] Support this Device in MTK table! c8d1
[ 2.420000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (Unknown NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[ 2.430000] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.440000] Scanning device for bad blocks
[ 2.590000] Signature matched and data read!
[ 2.590000] load_fact_bbt success 1023
[ 2.600000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.610000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.620000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.620000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.630000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.640000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.650000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.660000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.670000] Creating 11 MTD partitions on "MT7621-NAND":
[ 2.680000] 0x000000000000-0x000000080000 : "u-boot"
[ 2.690000] 0x000000080000-0x000000100000 : "debug"
[ 2.690000] 0x000000100000-0x000000140000 : "Factory"
[ 2.700000] 0x000000140000-0x000002140000 : "firmware"
[ 2.710000] 2 uimage-fw partitions found on MTD device firmware
[ 2.710000] 0x000000140000-0x0000002c0000 : "kernel"
[ 2.720000] 0x0000002c0000-0x000002140000 : "rootfs"
[ 2.730000] mtd: device 5 (rootfs) set to be root filesystem
[ 2.730000] 0x000002140000-0x0000021c0000 : "hw_panic"
[ 2.740000] 0x0000021c0000-0x000002240000 : "bdinfo"
[ 2.780000] 0x000002240000-0x0000022c0000 : "backup"
[ 2.790000] 0x0000022c0000-0x0000032c0000 : "overlay"
[ 2.790000] 0x0000032c0000-0x0000052c0000 : "firmware_backup"
[ 2.800000] 0x0000052c0000-0x0000054c0000 : "oem"
[ 2.810000] 0x0000054c0000-0x000007f80000 : "opt"
[ 2.810000] [mtk_nand] probe successfully!
[ 2.820000] GMAC1_MAC_ADRH -- : 0x0000d4ee
[ 2.820000] GMAC1_MAC_ADRL -- : 0x07543260
[ 2.830000] PROC INIT OK!
[ 2.830000] Ralink APSoC Hardware Watchdog Timer
[ 2.840000] TCP: cubic registered
[ 2.840000] NET: Registered protocol family 17
[ 2.840000] 8021q: 802.1Q VLAN Support v1.8
[ 2.850000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 2.860000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.870000] Freeing unused kernel memory: 248K (813e2000 - 81420000)
procd: Console is alive
[ 5.240000] usbcore: registered new interface driver usbfs
[ 5.240000] usbcore: registered new interface driver hub
[ 5.250000] usbcore: registered new device driver usb
[ 5.290000] SCSI subsystem initialized
procd: - preinit -
[ 6.280000] boot from nand
[ 6.400000] UBI: attaching mtd9 to ubi0
[ 6.550000] UBI: scanning is finished
[ 6.570000] UBI: attached mtd9 (name "overlay", size 16 MiB) to ubi0
[ 6.570000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 6.580000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 6.590000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 6.590000] UBI: good PEBs: 128, bad PEBs: 0, corrupted PEBs: 0
[ 6.600000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 6.610000] UBI: max/mean erase counter: 402/238, WL threshold: 4096, image sequence number: 82760497
[ 6.610000] UBI: available PEBs: 0, total reserved PEBs: 128, PEBs reserved for bad PEB handling: 20
[ 6.620000] UBI: background thread "ubi_bgt0d" started, PID 316
UBI device number 0, total 128 LEBs (16252928 bytes, 15.5 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 6.700000] UBIFS: background thread "ubifs_bgt0_0" started, PID 338
[ 6.770000] UBIFS: recovery needed
[ 7.060000] UBIFS: recovery completed
[ 7.070000] UBIFS: mounted UBI device 0, volume 0, name "overlay"
[ 7.070000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 7.080000] UBIFS: FS size: 11935744 bytes (11 MiB, 94 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 7.090000] UBIFS: reserved for root: 563754 bytes (550 KiB)
[ 7.100000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2A66EA76-16D5-4645-A99E-1189A394EE8C, small LPT model
mounting /dev/root
procd: - early -
procd: - ubus -
procd: - init -
[ 8.490000] NET: Registered protocol family 10
[ 8.820000] MT7603E module init
[ 8.830000] MT7603E AP Driver version-4.0.1.0rev2.P1
[ 9.660000] MT7612E module init
[ 9.670000] MT76x2 AP Driver version-3.0.4.0.P2.20160308
[ 10.580000] Initializing XFRM netlink socket
[ 10.590000] NET: Registered protocol family 15
[ 10.610000] loop: module loaded
[ 10.610000] tun: Universal TUN/TAP device driver, 1.6
[ 10.620000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 10.650000] l2tp_core: L2TP core driver, V2.0
[ 10.660000] l2tp_netlink: L2TP netlink interface
[ 10.670000] sit: IPv6 over IPv4 tunneling driver
[ 10.680000] exFAT: Version 1.2.9
[ 10.680000] gre: GRE over IPv4 demultiplexor driver
[ 10.690000] ip_gre: GRE over IPv4 tunneling driver
[ 10.700000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.710000] ehci-platform: EHCI generic platform driver
[ 10.750000] nf_conntrack version 0.5.0 (3983 buckets, 15932 max)
[ 10.760000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.770000] Netfilter messages via NETLINK v0.30.
[ 10.780000] ip_set: protocol 6
[ 10.820000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.830000] ***Module syslog inserted(log_addr:8d04c000)***
[ 10.840000] *****run project phy.
[ 10.870000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 10.890000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 10.910000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 10.930000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 10.950000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 10.970000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 10.990000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.020000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.040000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.070000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.150000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.180000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.210000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.230000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.250000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.280000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.310000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.330000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.350000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.380000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 11.550000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 11.550000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
[ 11.560000] xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000
[ 11.570000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 11.570000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.580000] usb usb1: Product: xHCI Host Controller
[ 11.580000] usb usb1: Manufacturer: Linux 3.10.49 xhci-hcd
[ 11.590000] usb usb1: SerialNumber: xhci-hcd
[ 11.600000] hub 1-0:1.0: USB hub found
[ 11.600000] hub 1-0:1.0: 2 ports detected
[ 11.600000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 11.610000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
[ 11.620000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 11.620000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.630000] usb usb2: Product: xHCI Host Controller
[ 11.640000] usb usb2: Manufacturer: Linux 3.10.49 xhci-hcd
[ 11.640000] usb usb2: SerialNumber: xhci-hcd
[ 11.650000] hub 2-0:1.0: USB hub found
[ 11.650000] hub 2-0:1.0: 1 port detected
[ 11.660000] i2c-gpio i2c-gpio.0: using pins 3 (SDA) and 4 (SCL)
[ 11.680000] u32 classifier
[ 11.690000] input device check on
[ 11.690000] Actions configured
[ 11.700000] Mirror/redirect action on
[ 11.700000] Failed to load ipt action
[ 11.730000] fuse init (API version 7.22)
[ 11.750000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.870000] ctnetlink v0.93: registering with nfnetlink.
[ 12.890000] rtc-pt7c4338 0-0068: rtc core: registered pt7c4338 as rtc0
[ 12.900000] usbcore: registered new interface driver usb-storage
[ 12.950000] xt_time: kernel timezone is -0000
[ 12.970000] PPP generic driver version 2.4.2
[ 12.970000] PPP MPPE Compression module registered
[ 12.980000] NET: Registered protocol family 24
[ 12.990000] p p t p driver version 0.8.5
[ 13.000000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 14.560000] oem: use pcba GM2101v01
Jan 1 08:04:46 Hiwifi syslog.info syslogd started: BusyBox v1.22.1
Jan 1 08:04:46 Hiwifi kern.notice kernel: klogd started: BusyBox v1.22.1 (2017-12-21 01:33:16 CST)
Jan 1 08:04:46 Hiwifi kern.notice kernel: [ 0.000000] Linux version 3.10.49 (build@DEV-9-1-242) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 1.4.8.20462s) ) #1 SMP Thu Dec 21 01:52:40 CST 2017
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000]
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] The CPU feqenuce set to 880 MHz
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] GCMP present
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Software DMA cache coherency
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Determined physical RAM map:
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] memory: 10000000 @ 00000000 (usable)
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Zone ranges:
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] DMA [mem 0x00000000-0x00ffffff]
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Normal [mem 0x01000000-0x0fffffff]
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Movable zone start for each node
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Early memory node ranges
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] node 0: [mem 0x00000000-0x0fffffff]
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] On node 0 totalpages: 65536
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 813ca180, node_mem_map 81468000
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] DMA zone: 32 pages used for memmap
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] DMA zone: 0 pages reserved
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] DMA zone: 4096 pages, LIFO batch:0
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] Normal zone: 480 pages used for memmap
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] Normal zone: 61440 pages, LIFO batch:15
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Detected 3 available secondary CPU(s)
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] PERCPU: Embedded 7 pages/cpu @8166b000 s6976 r8192 d13504 u32768
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] pcpu-alloc: s6976 r8192 d13504 u32768 alloc=8*4096
Jan 1 08:04:46 Hiwifi kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Jan 1 08:04:46 Hiwifi kern.warn kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Jan 1 08:04:46 Hiwifi kern.notice kernel: [ 0.000000] Kernel command line: board=HC5962 console=ttyS1,115200 rootfstype=squashfs,jffs2
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Writing ErrCtl register=00000481
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Readback ErrCtl register=00000481
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] allocated 524288 bytes of page_cgroup
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
Jan 1 08:04:46 Hiwifi kern.info kernel: [ 0.000000] Memory: 254708k/262144k available (3267k kernel code, 7436k reservJan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Jan 1 08:04:46 Hiwifi syslog.info logfwd[1324]: [output tcp] <log_server> Use default 1024 for "buff_limit"
Jan 1 08:04:46 Hiwifi syslog.info logfwd[1325]: === logfwd 4.2.3 Start ===
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: lanport [0]: 1
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: lanport [1]: 2
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: lanport [2]: 3
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: wanport: 4
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: wan dev: eth2
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: lan dev: eth2
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: binfo name: HC5962
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: binfo type: router
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: sinfo type: NULL
Jan 1 08:04:47 Hiwifi daemon.crit hboardd: sinfo minsize: 0M
Jan 1 08:04:47 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:47 Hiwifi user.emerg syslog: ---stop ---
Jan 1 08:04:47 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:47 Hiwifi user.emerg syslog: no /usr/sbin/storaged2 found; none killed
Jan 1 08:04:47 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:47 Hiwifi user.emerg syslog: storaged2:
Jan 1 08:04:47 Hiwifi user.emerg syslog: ---start---
Jan 1 08:04:47 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:47 Hiwifi user.notice /init.d/storaged2: <1394> /init.d/storaged2 boot
Jan 1 08:04:47 Hiwifi user.emerg syslog: storaged2:
Jan 1 08:04:47 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:48 Hiwifi user.warn wpad[1443]: uci reload success
Jan 1 08:04:48 Hiwifi user.warn wpad[1443]: router is master, macaddr: D4:EE:07:54:32:60
Jan 1 08:04:48 Hiwifi user.warn wpad[1443]: wlog_init
[ 18.640000] [NOTICE] <XT_TIME_CONF> (time_conf_init:140) xt_timc_conf module init
Jan 1 08:04:49 Hiwifi kern.warn kernel: [ 18.640000] [NOTICE] <XT_TIME_CONF> (time_conf_init:140) xt_timc_conf module init
Jan 1 08:04:49 Hiwifi user.notice firewall: Error: Failed to connect to ubus
Jan 1 08:04:49 Hiwifi user.notice wireless: procd[1]-->S20network[1525]-->wifi down
Jan 1 08:04:49 Hiwifi user.emerg syslog: wireless: procd[1]-->S20network[1525]-->wifi down
Jan 1 08:04:49 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:50 Hiwifi user.warn wpad[1443]: uci reload success
Jan 1 08:04:50 Hiwifi user.warn wpad[1443]: himsg_handle_wireless_down radio0
Jan 1 08:04:50 Hiwifi user.warn wpad[1443]: uci reload success
Jan 1 08:04:50 Hiwifi user.warn wpad[1443]: himsg_handle_wireless_down radio1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: netifd_ubus_init:1180: connected as c9d060e8
[ 19.570000] MT7530 Reset Completed!!
Jan 1 08:04:50 [ 19.580000] phy_free_head is 0xc54000!!!
Hiwifi kern.warn[ 19.580000] phy_free_tail_phy is 0xc55ff0!!!
kernel: [ 19.[ 19.590000] txd_pool=a0c58000 phy_txd_pool=00C58000
570000] MT7530 R[ 19.590000] ei_local->skb_free start address is 0x8faa26c4.
eset Completed!![ 19.600000] free_txd: 00c58010, ei_local->cpu_ptr: 00C58000
Jan 1 08:04:5[ 19.610000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
0 Hiwifi kern.wa[ 19.610000] ----------------+---------+--------
rn kernel: [ 1[ 19.620000] 0xa0c58000 0x00C58000 0x00C58000
9.580000] phy_fr[ 19.630000]
[ 19.630000] phy_qrx_ring = 0x00c56000, qrx_ring = 0xa0c56000
ee_head is 0xc54000!!!
Jan 1 0[ 19.640000]
[ 19.640000] phy_rx_ring0 = 0x00c60000, rx_ring0 = 0xa0c60000
8:04:50 Hiwifi k[ 19.640000] GMAC1_MAC_ADRH -- : 0x0000d4ee
ern.warn kernel:[ 19.650000] GMAC1_MAC_ADRL -- : 0x07543260
[ 19.580000] [ 19.660000] GDMA2_MAC_ADRH -- : 0x0000d4ee
phy_free_tail_ph[ 19.660000] GDMA2_MAC_ADRL -- : 0x07543261
y is 0xc55ff0!!!
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.590000] txd_pool=a0c58000 phy_txd_pool=00C58000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.590000] ei_local->skb_free start address is 0x8faa26c4.
Jan 1 08:04:50 Hiwifi daemon.debug netifd: proto_shell_add_handler:828: Add handler for script ./dhcp.sh: dhcp
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.600000] free_txd: 00c58010, ei_local->cpu_ptr: 00C58000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.610000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.610000] ----------------+---------+--------
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.620000] 0xa0c58000 0x00C58000 0x00C58000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.630000]
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.630000] phy_qrx_ring = 0x00c56000, qrx_ring = 0xa0c56000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.640000]
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.640000] phy_rx_ring0 = 0x00c60000, rx_ring0 = 0xa0c60000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.640000] GMAC1_MAC_ADRH -- : 0x0000d4ee
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.650000] GMAC1_MAC_ADRL -- : 0x07543260
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.660000] GDMA2_MAC_ADRH -- : 0x0000d4ee
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.660000] GDMA2_MAC_ADRL -- : 0x07543261
Jan 1 08:04:50 Hiwifi daemon.debug netifd: proto_shell_add_handler:828: Add handler for script ./l2tp.sh: l2tp
Jan 1 08:04:50 Hiwifi daemon.debug netifd: proto_shell_add_handler:828: Add handler for script ./ppp.sh: ppp
Jan 1 08:04:50 Hiwifi daemon.debug netifd: proto_shell_add_handler:828: Add handler for script ./ppp.sh: pppoe
Jan 1 08:04:50 Hiwifi user.notice wireless: procd[1]-->S20network[1525]-->wifi
Jan 1 08:04:50 Hiwifi user.emerg syslog: wireless: procd[1]-->S20network[1525]-->wifi
Jan 1 08:04:50 Hiwifi syslog.warn logfwd[1325]: [output tcp] <log_server> getaddrinfo() failed with error=Name or service not known, will try later
Jan 1 08:04:50 Hiwifi daemon.debug netifd: proto_shell_add_handler:828: Add ha[ 19.900000] ra2880stop()...ndler for scriptDone
./ppp.sh: p p t p
Jan 1 08:04:50 Hiwifi daemon.d[ 19.900000] Free TX/RX Ring Memory!
ebug netifd: interface_update:1077: Create interface 'loopback'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_create_default:313: Create simple device 'lo'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_init_virtual:278: Initialize device 'lo'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_set_present:402: Network device 'lo' is now present
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'lo', refcount=1
J[ 19.950000] MT7530 Reset Completed!!
an 1 08:04:50 Hiwifi daemon.debug netifd: interface_set_available:359: Interface 'loopback', available=1
Jan 1 08:04:50 Hiwif[ 19.960000] phy_free_head is 0xc54000!!!
i daemon.debug n[ 19.970000] phy_free_tail_phy is 0xc55ff0!!!
etifd: device_ad[ 19.970000] txd_pool=a0c58000 phy_txd_pool=00C58000
d_user:462: Add [ 19.980000] ei_local->skb_free start address is 0x8faa26c4.
user for device [ 19.990000] free_txd: 00c58010, ei_local->cpu_ptr: 00C58000
'lo', refcount=2[ 19.990000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
Jan 1 08:04:5[ 20.000000] ----------------+---------+--------
0 Hiwifi daemon.[ 20.010000] 0xa0c58000 0x00C58000 0x00C58000
debug netifd: de[ 20.010000]
[ 20.010000] phy_qrx_ring = 0x00c56000, qrx_ring = 0xa0c56000
vice_create:660: Create new devi[ 20.020000]
[ 20.020000] phy_rx_ring0 = 0x00c60000, rx_ring0 = 0xa0c60000
ce 'br-lan' (Bri[ 20.030000] GMAC1_MAC_ADRH -- : 0x0000d4ee
dge)
Jan 1 08:[ 20.040000] GMAC1_MAC_ADRL -- : 0x07543260
04:50 Hiwifi daemon.debug netifd: device_init_vi[ 20.040000] device eth2 entered promiscuous mode
rtual:278: Initialize device 'br-lan'
Jan 1 08[ 20.050000] br-lan: port 1(eth2) entered forwarding state
:04:50 Hiwifi da[ 20.060000] br-lan: port 1(eth2) entered forwarding state
emon.debug netifd: interface_update:1077: Create interface 'lan'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for [ 20.080000] ethernet:eth3 up
device 'br-lan', refcount=1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'br-lan', refcount=2
Jan 1 08:04:50 Hiwifi daemon.debug netifd: interface_update:1077: Create interface 'wan'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_create_default:313: Create simple device 'eth3'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_init_virtual:278: Initialize device 'eth3'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_set_present:402: Network device 'eth3' is now present
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'eth3', refcount=1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: interface_set_available:359: Interface 'wan', available=1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'eth3', refcount=2
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_create:660: Create new device 'br-lan1' (Bridge)
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_init_virtual:278: Initialize device 'br-lan1'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: interface_update:1077: Create interface 'lan1'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'br-lan1', refcount=1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'br-lan1', refcount=2
Jan 1 08:04:50 Hiwifi daemon.debug netifd: cb_clear_event:579: Remove a rule
Jan 1 08:04:50 Hiwifi daemon.debug netifd: config_init_wireless:362: device radio0 not found!
Jan 1 08:04:50 Hiwifi daemon.debug netifd: config_init_wireless:362: device radio1 not found!
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_create_default:313: Create simple device 'eth2'
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_init_virtual:278: Initialize device 'eth2'
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.900000] ra2880stop()...Done
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.900000] Free TX/RX Ring Memory!
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_set_present:402: Network device 'eth2' is now present
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'eth2', refcount=1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_set_present:402: Bridge 'br-lan' is now present
Jan 1 08:04:50 Hiwifi daemon.debug netifd: interface_set_available:359: Interface 'lan', available=1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_claim:224: Claim Bridge br-lan, new active count: 1
Jan 1 08:04:50 Hiwifi daemon.debug netifd: device_claim:224: Claim Network device eth2, new active count: 1
Jan 1 08:04:50 Hiwifi user.notice /init.d/storaged2: <1394> recover_info ----
Jan 1 08:04:50 Hiwifi user.info syslog: pid(1412):error:wait_data_available:40:select fd 3 failed, rc=-1 errno=4
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.950000] MT7530 Reset Completed!!
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.960000] phy_free_head is 0xc54000!!!
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.970000] phy_free_tail_phy is 0xc55ff0!!!
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.970000] txd_pool=a0c58000 phy_txd_pool=00C58000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.980000] ei_local->skb_free start address is 0x8faa26c4.
Jan 1 08:04:50 Hiwifi user.notice /init.d/storaged2: <1394> uci get hiwifi.storage.data_uuid=
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.990000] f[ 20.370000] device ra0 entered promiscuous mode
ree_txd: 00c5801[ 20.380000] br-lan: port 2(ra0) entered forwarding state
0, ei_local->cpu[ 20.390000] br-lan: port 2(ra0) entered forwarding state
_ptr: 00C58000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 19.990000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 20.000000] ----------------+---------+--------
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 20.010000] 0xa0c58000 0x00C58000 0x00C58000
Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 20.01000Jan 1 08:04:50 Hiwifi kern.warn kernel: [ 20.Jan 1 08:04:50 Jan 1 08:04:50 Hiwifi user.notice /init.d/storaJan 1 08:04:50 Jan 1 08:04:50 Hiwifi kern.info kernel: [ 20.Jan 1 08:04:50 Jan 1 08:04:50 Jan 1 08:04:50 Jan 1 08:04:50 Jan 1 08:04:50 Hiwifi daemon.debug netifd: get_Jan 1 08:04:50 Jan 1 08:04:50 Jan 1 08:04:50 Jan 1 08:04:50 Hiwifi kern.warnJan 1 08:04:50 Hiwifi daemon.notice netifd: wan (1759): udhcpc (v1.22.1) started
Jan 1 08:04:50 Hiwifi user.warn wpad[1443]: uci reload success
Jan 1 08:04:50 Hiwifi user.warn wpad[1443]: himsg_handle_wireless_down radio1
Jan 1 08:04:51 Hiwifi user.notice switch: reset switch(lan)
Jan 1 08:04:51 Hiwifi user.warn wpad[1443]: uci reload success
Jan 1 08:04:51 Hiwifi user.warn wpad[1443]: himsg_handle_wireless_up radio0
Jan 1 08:04:51 Hiwifi user.warn wpad[1443]: up interface ra0
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_create_default:313: Create simple device 'ra0'
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_init_virtual:278: Initialize device 'ra0'
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_set_present:402: Network device 'ra0' is now present
Jan 1 08:04:51 Hiwifi daemon.notice netifd: Network device 'ra0' link is up
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'ra0', refcount=1
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_claim:224: Claim Network device ra0, new active count: 1
Jan 1 08:04:51 Hiwifi kern.info kernel: [ 20.370000] device ra0 entered promiscuous mode
Jan 1 08:04:51 Hiwifi kern.info kernel: [ 20.380000] br-lan: port 2(ra0) entered forwarding state
Jan 1 08:04:51 Hiwifi kern.info kernel: [ 20.390000] br-lan: port 2(ra0) entered forwarding state
Jan 1 08:04:51 Hiwifi user.notice capshd_slave: udhcpc event received: deconfig
Jan 1 08:04:51 Hiwifi daemon.notice netifd: wan (1759): Sending discover...
Jan 1 08:04:51 Hiwifi user.notice ifup: Enabling Router Solicitations on lan (br-lan)
[ 21.010000] device rai0 entered promiscuous modeload success
Jan 1 08:04:51[ 21.010000] br-lan: port 3(rai0) entered forwarding state
Hiwifi user.war[ 21.020000] br-lan: port 3(rai0) entered forwarding state
n wpad[1443]: himsg_handle_wireless_up radio1
Jan 1 08:04:51 Hiwifi user.warn wpad[1443]: up interface rai0
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_create_default:313: Create simple device 'rai0'
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_init_virtual:278: Initialize device 'rai0'
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_set_present:402: Network device 'rai0' is now present
Jan 1 08:04:51 Hiwifi daemon.notice netifd: Network device 'rai0' link is up
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_add_user:462: Add user for device 'rai0', refcount=1
Jan 1 08:04:51 Hiwifi daemon.debug netifd: device_claim:224: Claim Network device rai0, new active count: 1
Jan 1 08:04:51 Hiwifi kern.info kernel: [ 21.010000] device rai0 entered promiscuous mode
Jan 1 08:04:51 Hiwifi kern.info kernel: [ 21.010000] br-lan: port 3(rai0) entered forwarding state
Jan 1 08:04:51 Hiwifi kern.info kernel: [ 21.020000] br-lan: port 3(rai0) entered forwarding state
Jan 1 08:04:52 Hiwifi user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Jan 1 08:04:52 Hiwifi user.notice firewall: * Populating IPv4 filter table
Jan 1 08:04:52 Hiwifi user.notice firewall: * Zone 'lan'
Jan 1 08:04:52 Hiwifi user.notice firewall: * Zone 'wan'
Jan 1 08:04:52 Hiwifi user.notice firewall: * Zone 'lan1'
Jan 1 08:04:52 Hiwifi user.notice firewall: * Rule 'Allow-DHCP-Renew'
Jan 1 08:04:52 Hiwifi user.notice firewall: * Rule 'Allow-Ping'
Jan 1 08:04:52 Hiwifi user.notice firewall: * Rule [ 21.420000] UBI: attaching mtd12 to ubi1
'Allow-ICMP-Unreachable'
Jan 1 08:04:52 Hiwifi user.notice firewall: * Rule 'Allow-IGMP'
Jan 1 08:04:52 Hiwifi user.notice firewall: * Rule 'Allow-UDP-igmpproxy'
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -P INPUT ACCEPT
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -P OUTPUT ACCEPT
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -P FORWARD DROP
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N delegate_input
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N delegate_output
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N delegate_forward
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N reject
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N input_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N output_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N forwarding_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N syn_flood
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_lan_input
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_lan_output
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_lan_forward
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_lan_src_ACCEPT
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_lan_dest_ACCEPT
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_lan_dest_REJECT
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N input_lan_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N output_lan_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N forwarding_lan_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -A zone_lan_input -m comment --comment "user chain for input" -j input_lan_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -A zone_lan_output -m comment --comment "user chain for output" -j output_lan_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -A zone_lan_forward -m comment --comment "user chain for forwarding" -j forwarding_lan_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_wan_input
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_wan_output
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_wan_forward
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_wan_src_REJECT
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_wan_dest_ACCEPT
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_wan_dest_REJECT
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N input_wan_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N output_wan_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N forwarding_wan_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -A zone_wan_input -m comment --comment "user chain for input" -j input_wan_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t f[ 21.710000] Simple address matching list for Netfilter - HiWiFi
ilter -A zone_wan_output -m comment --comment "user chain for output" -j output_wan_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -A zone_wan_forward -m comment --comment "user chain for forwarding" -j forwarding_wan_rule
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_lan1_input
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_lan1_output
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter -N zone_lan1_forward
Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Hiwifi user.notice firewall: iptables -t filter Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Hiwifi user.notice firewall: * Rule 'Allow-ICJan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Hiwifi user.notice firewall: * Populating IPv6 mangle table
JaJan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Hiwifi user.notiJan 1 08:04:52 Jan 1 08:04:52 Hiwifi daemon.crit hboardd: switch_wan_set_mode {"mode":"auto"}
Jan 1 08:04:52 Hiwifi daemon.notice hboardd: set wan mode to aJan 1 08:04:52 Hiwifi daemon.info /sbin/himsgd[Jan 1 08:04:52 Jan 1 08:04:52 Jan 1 08:04:52 Hiwifi kern.info kernel: [ 21.710000] Simple address matching list for Netfilter - HiWiFi
Jan 1 08:04:52 Hiwifi user.info iptables[1959]: <do_command4:1345> iptables -t nat -I PREROUTING -m state --state RELATED -i eth3 --proto gre -j ACCEPT
Jan 1 08:04:52 Hiwifi user.notice firewall: * Running script '/usr/share/miniupnpd/firewall.include'
Jan 1 08:04:52 Hiwifi user.info iptables[1966]: <do_command4:1345> iptables -t filter -N MINIUPNPD
Jan 1 08:0[ 21.880000] UBI: scanning is finished
4:52 Hiwifi user.info iptables[1968]: <do_command4:1345> iptables -t nat -N MINIUPNPD
Jan 1 08:04:52 Hiwifi user.info iptables[1972]: <do_command4:1345> iptables -t nat -N miniupnpd_fromlan
Jan 1 08:04:52 Hiwifi user.info iptables[1974]: <do_command4[ 21.900000] UBI: attached mtd12 (name "opt", size 42 MiB) to ubi1
:1345> iptables [ 21.910000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
-t nat -N miniup[ 21.920000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
npd_tolan
Jan [ 21.930000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
1 08:04:52 Hiwi[ 21.940000] UBI: good PEBs: 342, bad PEBs: 0, corrupted PEBs: 0
fi user.info ipt[ 21.940000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
ables[1976]: <do[ 21.950000] UBI: max/mean erase counter: 15/8, WL threshold: 4096, image sequence number: 1834583676
_command4:1345> [ 21.960000] UBI: available PEBs: 0, total reserved PEBs: 342, PEBs reserved for bad PEB handling: 20
iptables -N mini[ 21.970000] UBI: background thread "ubi_bgt1d" started, PID 1989
upnpd_fwd
Jan 1 08:04:52 Hiwifi user.info iptables[1981]: <do_command4:1345> iptables -t filter -I zone_wan_forward -j MINIUPNPD
Jan 1 08:04:52 Hiwifi user.info iptables[1982]: <do_command4:1345> iptabl[ 22.000000] UBIFS: background thread "ubifs_bgt1_0" started, PID 1998
es -t nat -I zone_wan_prerouting -j MINIUPNPD
Jan 1 08:04:52 Hiwifi kern.notice kernel: [ 21.880000] UBI: scanning is finished
Jan 1 08:04:52 Hiwifi user.info iptables[1987]: <do_command4:1345> iptables -t nat -I zone_lan_prerouting -j miniupnpd_fromlan
Jan 1 08:04:52 Hiwifi kern.notice kernel: [ 21.900000] UBI: attached mtd12 (name "opt", size 42 MiB) to ubi1
Jan 1 08:04:52 Hiwifi kern.notice kernel: [ 21.910000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
Jan 1 08:04:52 Hiwifi kern.notice kernel: [ 21.920000] UBI: min./max. I/O unit sizes: 2048/2[ 22.060000] br-lan: port 1(eth2) entered forwarding state
048, sub-page size 2048
Jan 1 08:04:52 Hiwifi kern.notice kernel: [ 21.93000[ 22.070000] UBIFS: recovery needed
0] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096

复制代码

gu***

http://192.168.199.1/local-ssh/ 用这个后门开！！

6538***

客户端已经不能用了吗？

eski***

我擦我也遇到了这个问题，救命

账号		自动登录	找回密码
密码			立即注册

求救，B70开root权限

相关帖子

本帖子中包含更多资源

欢迎大家光临恩山无线论坛 /1