WRT54G V7改DD折腾中 有线暂时无法驱动

洪***

WRT54G-V7 换FLASH、内存，刷网件624 V4固件

已知复位定义两者是相反，要按住复位键才能正常启动

启动后无线可以正常工作，有线部分是ADM6996I 与624-V4的ADM6996FC后缀不同

帖上启动信息：

Ethernet eth0: MAC address 00:00:88:08:08:08
IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.1.10

RedBoot(tm) bootstrap and debug environment [ROMRAM]
Ubiquiti Networks certified release, version 0.9.8.06 - built 10:58:08, Dec 23 2008

Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.

Board: Ubiquiti AR2315/6/7/8 based board
RAM: 0x80000000-0x82000000, [0x80040880-0x80fe1000] available
FLASH: 0xa8000000 - 0xa87f0000, 128 blocks of 0x00010000 bytes each.
== Executing boot script in 1.000 seconds - enter ^C to abort
RedBoot> fis load -l linux
Trying LZMA decompression...
Image loaded from 0x80041000-0x802e7b4c
RedBoot> exec
Now booting linux kernel:
Base address 0x80030000 Entry 0x80041000
Cmdline :
mem setup
scanning for root partition

found RedBoot partition at [0xA8000000]
found linux partition at [0xA8030000]
decode 1f02
start service
starting Architecture code for mr3202a
eth0: Atheros AR231x: 00:00:88:08:08:08, irq 4
ar2313_eth_mii: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:00)
load ATH 802.11 a/b/g Driver
ath_hal: module license 'Proprietary' taints kernel.
eth0: Configuring MAC for half duplex
Found ADM6996FC! PHYID1 is 0x1023, PHYID2 is 0x7
Port 0, Negotiation timeout
Port 1, Negotiation timeout
Port 2, Negotiation timeout
Port 3, Negotiation timeout
Port 4, Negotiation timeout
adm_phySetup: eth0 phy0: Phy Status=7849
adm_phySetup: eth0 phy1: Phy Status=7849
adm_phySetup: eth0 phy2: Phy Status=7849
adm_phySetup: eth0 phy3: Phy Status=7849
adm_phySetup: eth0 phy4: Phy Status=7849
adm_phySetup: eth0 phy5: Phy Status=840f
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device br0 entered promiscuous mode
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
device vlan2 entered promiscuous mode
sh: can't create /proc/sys/dev/wifi0/maxvaps: Permission denied
ath0
sh: can't create /proc/sys/dev/wifi0/csma: nonexistent directory
device ath0 entered promiscuous mode
br0: port 3(ath0) entering learning state
br0: port 2(vlan2) entering learning state
br0: port 1(vlan1) entering learning state
device br0 left promiscuous mode
device br0 entered promiscuous mode
device br0 left promiscuous mode
device br0 entered promiscuous mode
br0: topology change detected, propagating
br0: port 3(ath0) entering forwarding state
br0: topology change detected, propagating
br0: port 2(vlan2) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
br0: No such process
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
connect: Network is unreachable
connect: Network is unreachable
connect: Network is unreachable
gethostbyname: Network is unreachable
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
etherip: Ethernet over IPv4 tunneling driver
connect: Network is unreachable
connect: Network is unreachable
connect: Network is unreachable
gethostbyname: Network is unreachable

DD-WRT v24-sp2 std (c) 2010 NewMedia-NET GmbH
Release: 06/30/10 (SVN revision: 14684)

DD-WRT login:

洪***

找到OPENWRT 上的ADM6996补丁，菜鸟摸索中

luhuam***

顶一个,祝你成功!

桃***

祝你成功！！！！！！！

洪***

刷上UBNT正常   看看有没高人帮忙搞驱动了

dj***

我也有一台.折腾过几下.
复位那里易解决.
只是刷了DD的话.交换芯片没办法驱动.试了几个DD固件,都不行.可能是交换芯片的模式选择不对.只是没去查哪一个脚是切换模式的.

jack***

洪饼 发表于 2010-10-17 20:44
找到OPENWRT 上的ADM6996补丁，菜鸟摸索中

用redboot_ap51_32M_4M_admtek.rom
刷ATTITUDE ADJUSTMENT (12.09-beta, r33312)
可以驱动6996i

savi***

前几个星期也折腾过，想编译op。不过不成功，放弃了。

yuek***

wrt54g v7谁知道jtag线序？能不能共享一下呢？