WR941N V2改USB后 不能识别U盘

lhlpyl

TP 941n v2 加了USB接口和供电电路，同时R96也加了电阻（10K），刷了猫大编译的U-boot 但是就是不能识别U盘。
大家帮忙看看是哪里出了问题？


U-Boot 1.1.4 (Jul 17 2010 - 00:26:05)

AP81 (ar7100) U-boot
DRAM:  
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Hit any key to stop autoboot:  0
## Booting image at bf020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.37.6 (dyq@dyq-desktop) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #1 Sun May 29 15:19:25 CST 2011
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
SoC: Atheros AR9132 rev 2
Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:100.000MHz, Ref:5.000MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line:  board=TL-WR941ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29480k/32768k available (1931k kernel code, 3288k reserved, 370k data, 168k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:80
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR941ND
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: found s25sl064a, expected m25p80
m25p80 spi0.0: s25sl064a (8192 Kbytes)
Searching for RedBoot partition table in spi0.0 at offset 0x7e0000
Searching for RedBoot partition table in spi0.0 at offset 0x7f0000
No RedBoot partition table detected in spi0.0
spi0.0: no WRT160NL signature found
Creating 6 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000160000 : "kernel"
0x000000160000-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=5F0000, len=200000
0x0000005f0000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "art"
0x000000020000-0x0000007f0000 : "firmware"
0x000000000000-0x000000800000 : "fullflash"
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registered
NET: Registered protocol family 17
Distributed Switch Architecture driver version 0.1
eth0[0]: detected a Marvell 88E6060 switch
dsa slave smi: probed
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 168k freed
input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
Button Hotplug driver version 0.4.1
eth0: link up (100Mbps/Full duplex)
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
JFFS2 notice: (445) jffs2_build_xattr_subsystem: complete building xattr subsystem, 27 of xdatum (0 unchecked, 26 orphan) and 52 of xref (0 dead, 26 orphan) found.
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
switching to jffs2
- init -
eth0: link down

Please press Enter to activate this console. eth0: link up (100Mbps/Full duplex)
wan: link up, 100 Mb/s, full duplex, flow control disabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
device lan1 entered promiscuous mode
device eth0 entered promiscuous mode
device lan2 entered promiscuous mode
device lan3 entered promiscuous mode
device lan4 entered promiscuous mode
lan3: link up, 100 Mb/s, full duplex, flow control disabled
br-lan: port 3(lan3) entering forwarding state
br-lan: port 3(lan3) entering forwarding state
Compat-wireless backport release: compat-wireless-2011-05-11-1-g501c91f
Backport based on wireless-testing.git master-2011-05-13
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (463 buckets, 1852 max)
xt_time: kernel timezone is -0000

lhlpyl

root@OpenWrt:/# lsmod
Module                  Size  Used by    Not tainted
gpio_buttons            1920  0
ledtrig_usbdev          2032  0
nf_nat_irc               784  0
nf_conntrack_irc        2480  1 nf_nat_irc
nf_nat_ftp               976  0
nf_conntrack_ftp        4416  1 nf_nat_ftp
xt_HL                   1200  0
xt_hl                    720  0
ipt_ECN                 1280  0
xt_CLASSIFY              448  0
xt_time                 1472  0
xt_tcpmss                896  0
xt_statistic             720  0
xt_mark                  592  0
xt_length                592  0
ipt_ecn                  880  0
xt_DSCP                 1296  0
xt_dscp                  912  0
ipt_MASQUERADE           928  1
iptable_nat             2128  1
nf_nat                  9808  4 nf_nat_irc,nf_nat_ftp,ipt_MASQUERADE,iptable_nat
xt_recent               5888  0
xt_helper                800  0
xt_connmark              960  0
xt_connbytes            1312  0
xt_conntrack            1648  0
xt_NOTRACK               464  0
iptable_raw              576  1
xt_state                 624  3
nf_conntrack_ipv4       3808  6 iptable_nat,nf_nat
nf_defrag_ipv4           624  1 nf_conntrack_ipv4
nf_conntrack           36576 14 nf_nat_irc,nf_conntrack_irc,nf_nat_ftp,nf_conntrack_ftp,ipt_MASQUERADE,iptable_nat,nf_nat,xt_helper,xt_connmark,xt_connbytes,xt_conntrack,xt_NOTRACK,xt_state,nf_conntrack_ipv4
pppoe                   7216  2
pppox                   1152  1 pppoe
ipt_REJECT              1616  2
xt_TCPMSS               1744  2
ipt_LOG                 5840  0
xt_comment               416  0
xt_multiport            1104  0
xt_mac                   544  0
xt_limit                 960  1
iptable_mangle           864  0
iptable_filter           640  1
ip_tables               8352  4 iptable_nat,iptable_raw,iptable_mangle,iptable_filter
xt_tcpudp               1568  5
x_tables               10032 33 xt_HL,xt_hl,ipt_ECN,xt_CLASSIFY,xt_time,xt_tcpmss,xt_statistic,xt_mark,xt_length,ipt_ecn,xt_DSCP,xt_dscp,ipt_MASQUERADE,iptable_nat,xt_recent,xt_helper,xt_connmark,xt_connbytes,xt_conntrack,xt_NOTRACK,iptable_raw,xt_state,ipt_REJECT,xt_TCPMSS,ipt_LOG,xt_comment,xt_multiport,xt_mac,xt_limit,iptable_mangle,iptable_filter,ip_tables,xt_tcpudp
ppp_async               6000  0
ppp_generic            18384  7 pppoe,pppox,ppp_async
slhc                    4000  1 ppp_generic
vfat                    7776  0
fat                    41152  1 vfat
ath9k                  75264  0
ath9k_common            1024  1 ath9k
ath9k_hw              252352  2 ath9k,ath9k_common
ath                    13296  2 ath9k,ath9k_hw
nls_utf8                 784  0
mac80211              206400  1 ath9k
crc_ccitt                944  1 ppp_async
cfg80211              124320  3 ath9k,ath,mac80211
compat                  2448  1 mac80211
arc4                     768  2
aes_generic            29840  0
crypto_algapi           9008  2 arc4,aes_generic
usb_storage            32544  0
ohci_hcd               16560  0
ehci_hcd               32064  0
sd_mod                 21072  0
ext4                  217808  0
jbd2                   36048  1 ext4
usbcore                95120  5 ledtrig_usbdev,usb_storage,ohci_hcd,ehci_hcd
scsi_mod               67808  2 usb_storage,sd_mod
nls_base                4544  4 vfat,fat,nls_utf8,usbcore
mbcache                 3504  1 ext4
crc16                    944  1 ext4
leds_gpio               1584  0
button_hotplug          2672  0
gpio_keys_polled        2080  0
input_polldev           2064  2 gpio_buttons,gpio_keys_polled
input_core             18864  5 gpio_buttons,button_hotplug,gpio_keys_polled,input_polldev

lhlpyl

别人没有遇到过这种情况吗 ？

A-Coder

在淘宝买了一款1041的带USB口, 在openwrt里面已经make menuconfig->kernerl module 里面选了USB support 和native language等相关选项 怎么还不能够识别U盘? 奇怪...uhci ohci usb2 vfat格式 ntfs格式 都选了

我郁闷