|
|
DB120，双USB口，S29的Falsh，刷了一个带有密码的电信原版固件，通电后USB2,USB1和WLAN等亮绿灯，DSL绿灯闪烁，Power绿灯。无法进入192.168.1.1界面
启动信息如下：
CFE> 﨎oot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
AuxFS[93,0xbeba0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE: 0x80401000 - 0x80529850 (1214544)
Initialized Data: 0x8041E730 - 0x80421050 (10528)
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:1e:40:4b:0c:76
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number [0|1] : 0
udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x8026c018
Decompression OK!
Entry at 0x8026c018
Closing network.
Starting program at 0x8026c018
Linux version 2.6.8.1 (root@localhost.qsl) (gcc version 3.4.2) #1 Fri Mar 27 19:32:00 CST
2009
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
fInfo.flash_rootfs_available_length = 16252928
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29344k/32384k available (1908k kernel code, 2996k reserved, 503k data, 76k init, 0k
highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
Computing partition layout for flash of size[16777216] sectors[128]
Flash split 25% into RootFS+Kernel[12058624] : AuxFS[4194304]
Partition ROOTFS_KRN [0xbe020000, 12058624] Blks[ 92: 1 .. 92]
SubPartition Image 1 [0xbe020000, 6029312] Blks[ 46: 1 .. 46]
SubPartition Image 2 [0xbe5e0000, 6029312] Blks[ 46: 47 .. 92]
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 1 131072 131072 0xbe000580 1024 BOOTLOADER
1 0 92 131072 12058624 0xbe020000 12058624 ROOTFS_KRN
93 0 32 131072 4194304 0xbeba0000 4194304 JFFS_AUXFS
125 0 1 131072 131072 0xbefa0000 131072 LOG_SCRPAD
126 106496 1 131072 131072 0xbefda000 24576 TW_PERSISTMEM
127 106496 1 131072 131072 0xbeffa000 24576 PERSISTMEM
Can't analyze prologue code at 801eb844
SCSI subsystem initialized
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe020100
Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xbe020100,4091904]
Registered device mtd[BCM63XX AuxFS] dev[1] Flash[0xbeba0000,4194304]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
WIFI: Button Interrupt 0x0 is enabled
WIFI: map_external_irq begin
SES: LED GPIO 0x8018 is enabled
initLed: led[0]: mask=0x400000, state=0
initLed: led[1]: mask=0x0100, state=0
initLed: led[2]: mask=0x1000000, state=0
initLed: led[3]: mask=0x0001, state=0
initLed: led[4]: mask=0x0004, state=0
initLed: led[5]: mask=0x0010, state=0
initLed: led[6]: mask=0x0002, state=0
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started: BusyBox v1.00 (2009.03.27-11:37+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
cp: /etc/hosts: No such file or directory
TTL进入CFE后，两个USB灯都是绿灯，POWER灯红灯。
启动信息如下
[quote]Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
AuxFS[93,0xbeba0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE: 0x80401000 - 0x80529850 (1214544)
Initialized Data: 0x8041E730 - 0x80421050 (10528)
*** Break into CFE console ***
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:1e:40:4b:0c:76
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number [0|1] : 0
udp_send finished
No answer .auto boot ...
CFE>
Board Id，Number of MAC Addresses，Base MAC Address 等都重新配置过。
Board Id试过0，1
Base MAC Address 是按照板子上贴的标签填写的。
Number of MAC Addresses试过11和12（不知道是填11还是12）
在IE中无法打开192.168.1.1，无法进入升级界面。
请不要胡乱输入以及粘贴、复制等方式灌水
请尊重作者、并共同维护网站的正常阅读，否则账户将会被限制发帖、回帖，站内短信以及阅读权限等都会受到影响，谢谢。
具体限制方式：https://www.right.com.cn/forum/thread-8307840-1-1.html
|
|
/1 
IP卡
狗仔卡
发表于 2012-1-18 09:41
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
