(已解决)急救用wr703n+MF190拨号成功却上不了网的问题

cnyeewa · 发表于 2012-2-7 17:40

本帖最后由 cnyeewa 于 2012-2-9 18:06 编辑

刷了openwrt固件，并按教程编写好所有文件，在日志看到是拨号成功了，却上不了网，请各位大大帮忙看看

Sep  8 19:37:34 OpenWrt kern.info kernel: usb 1-1: USB disconnect, device number 3
Sep  8 19:37:34 OpenWrt kern.info kernel: option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
Sep  8 19:37:34 OpenWrt kern.info kernel: option 1-1:1.0: device disconnected
Sep  8 19:37:34 OpenWrt kern.info kernel: option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
Sep  8 19:37:34 OpenWrt kern.info kernel: option 1-1:1.1: device disconnected
Sep  8 19:37:34 OpenWrt kern.err kernel: option: option_instat_callback: error -143
Sep  8 19:37:34 OpenWrt kern.info kernel: option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
Sep  8 19:37:34 OpenWrt kern.info kernel: option 1-1:1.2: device disconnected
Sep  8 19:37:34 OpenWrt daemon.info pppd[1415]: Hangup (SIGHUP)
Sep  8 19:37:34 OpenWrt daemon.notice pppd[1415]: Modem hangup
Sep  8 19:37:34 OpenWrt daemon.info pppd[1415]: Connect time 40.1 minutes.
Sep  8 19:37:34 OpenWrt daemon.notice pppd[1415]: Connection terminated.
Sep  8 19:37:35 OpenWrt user.notice 3g-hotplug: Stopping interface wan1 for device ttyUSB2
Sep  8 19:37:35 OpenWrt user.info firewall: removing wan1 (3g-wan1) from zone wan
Sep  8 19:37:35 OpenWrt daemon.info pppd[1415]: Terminating on signal 15
Sep  8 19:37:36 OpenWrt user.info firewall: removing wan1 (3g-wan1) from zone root
Sep  8 19:37:36 OpenWrt daemon.info pppd[1415]: Exit.
Sep  8 19:37:41 OpenWrt kern.info kernel: usb 1-1: new high speed USB device number 4 using ar71xx-ehci
Sep  8 19:37:41 OpenWrt kern.info kernel: usbserial_generic 1-1:1.0: generic converter detected
Sep  8 19:37:41 OpenWrt kern.info kernel: usb 1-1: generic converter now attached to ttyUSB0
Sep  8 19:37:41 OpenWrt user.notice usb-modeswitch: 1-1:1.0: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=P671A2UCCS010000
Sep  8 19:37:41 OpenWrt user.notice usb-modeswitch: 1-1:1.0: Selecting /etc/usb_modeswitch.d/19d2:2000 for mode switching
Sep  8 19:37:41 OpenWrt kern.info kernel: generic ttyUSB0: generic converter now disconnected from ttyUSB0
Sep  8 19:37:41 OpenWrt kern.info kernel: usbserial_generic 1-1:1.0: device disconnected
Sep  8 19:37:41 OpenWrt kern.warn kernel: usb 1-1: usbfs: process 2000 (usb_modeswitch) did not claim interface 0 before use
Sep  8 19:37:47 OpenWrt kern.info kernel: usb 1-1: USB disconnect, device number 4
Sep  8 19:37:47 OpenWrt kern.info kernel: usb 1-1: new high speed USB device number 5 using ar71xx-ehci
Sep  8 19:37:47 OpenWrt kern.info kernel: option 1-1:1.0: GSM modem (1-port) converter detected
Sep  8 19:37:47 OpenWrt kern.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
Sep  8 19:37:47 OpenWrt kern.info kernel: option 1-1:1.1: GSM modem (1-port) converter detected
Sep  8 19:37:47 OpenWrt kern.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
Sep  8 19:37:47 OpenWrt kern.info kernel: option 1-1:1.2: GSM modem (1-port) converter detected
Sep  8 19:37:47 OpenWrt kern.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
Sep  8 19:37:49 OpenWrt user.notice usb-modeswitch: 1-1:1.0: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=P671A2UCCS010000
Sep  8 19:37:49 OpenWrt user.notice usb-modeswitch: 1-1:1.1: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=P671A2UCCS010000
Sep  8 19:37:50 OpenWrt user.notice usb-modeswitch: 1-1:1.2: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=P671A2UCCS010000
Sep  8 19:37:50 OpenWrt user.notice 3g-hotplug: Starting interface wan1 for device ttyUSB2
Sep  8 19:37:50 OpenWrt user.notice usb-modeswitch: 1-1:1.3: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=P671A2UCCS010000
Sep  8 19:37:54 OpenWrt daemon.notice pppd[2196]: pppd 2.4.5 started by root, uid 0
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: abort on (BUSY)
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: abort on (NO CARRIER)
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: abort on (ERROR)
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: report (CONNECT)
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: timeout set to 10 seconds
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: send (AT&F^M)
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: expect (OK)
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: AT&F^M^M
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: OK
Sep  8 19:37:55 OpenWrt local2.info chat[2201]:  -- got it
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: send (ATE1^M)
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: expect (OK)
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: ^M
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: ATE1^M^M
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: OK
Sep  8 19:37:55 OpenWrt local2.info chat[2201]:  -- got it
Sep  8 19:37:55 OpenWrt local2.info chat[2201]: send (AT+CGDCONT=1,"IP","3gnet"^M)
Sep  8 19:37:56 OpenWrt local2.info chat[2201]: timeout set to 30 seconds
Sep  8 19:37:56 OpenWrt local2.info chat[2201]: expect (OK)
Sep  8 19:37:56 OpenWrt local2.info chat[2201]: ^M
Sep  8 19:37:56 OpenWrt local2.info chat[2201]: AT+CGDCONT=1,"IP","3gnet"^M^M
Sep  8 19:37:56 OpenWrt local2.info chat[2201]: OK
Sep  8 19:37:56 OpenWrt local2.info chat[2201]:  -- got it
Sep  8 19:37:56 OpenWrt local2.info chat[2201]: send (ATD*99#^M)
Sep  8 19:37:56 OpenWrt local2.info chat[2201]: expect (CONNECT)
Sep  8 19:37:56 OpenWrt local2.info chat[2201]: ^M
Sep  8 19:37:56 OpenWrt local2.info chat[2201]: ATD*99#^M^M
Sep  8 19:37:56 OpenWrt local2.info chat[2201]: CONNECT
Sep  8 19:37:56 OpenWrt local2.info chat[2201]:  -- got it
Sep  8 19:37:56 OpenWrt local2.info chat[2201]: send ( ^M)
Sep  8 19:37:56 OpenWrt daemon.info pppd[2196]: Serial connection established.
Sep  8 19:37:56 OpenWrt daemon.info pppd[2196]: Using interface 3g-wan1
Sep  8 19:37:56 OpenWrt daemon.notice pppd[2196]: Connect: 3g-wan1 <--> /dev/ttyUSB2
Sep  8 19:38:00 OpenWrt daemon.warn pppd[2196]: Could not determine remote IP address: defaulting to 10.64.64.64
Sep  8 19:38:00 OpenWrt daemon.notice pppd[2196]: local  IP address 10.245.217.137
Sep  8 19:38:00 OpenWrt daemon.notice pppd[2196]: remote IP address 10.64.64.64
Sep  8 19:38:00 OpenWrt daemon.notice pppd[2196]: primary DNS address 192.168.8.1
Sep  8 19:38:01 OpenWrt user.notice ifup: Enabling Router Solicitations on wan1 (3g-wan1)
Sep  8 19:38:01 OpenWrt user.notice rdate: No usable time server for wan1 found
Sep  8 19:38:01 OpenWrt user.info firewall: adding wan1 (3g-wan1) to zone wan
Sep  8 19:38:02 OpenWrt user.info firewall: adding wan1 (3g-wan1) to zone root

请不要胡乱输入以及粘贴、复制等方式灌水

请尊重作者、并共同维护网站的正常阅读，否则账户将会被限制发帖、回帖，并且积分可能会被清零，站内短信以及阅读权限等都会受到影响，谢谢。具体限制方式：https://www.right.com.cn/forum/thread-8307840-1-1.html

cnyeewa · 发表于 2012-2-7 17:42

看到拨号已经成功，并取得DNS，

cnyeewa · 发表于 2012-2-7 17:45

我的3G卡有点特殊，是联通的APN卡，是直接绑定接入我们公司内网的

cnyeewa · 发表于 2012-2-8 08:37

没人帮下忙吗？

cnyeewa · 发表于 2012-2-8 14:45

怎么没人帮忙呀？

sutuo · 发表于 2012-2-8 20:10

防火墙问题

cnyeewa · 发表于 2012-2-9 13:07

已经/etc/init.d/firewall stop，已经把防火墙关了，怎么没有高手帮下忙的

cnyeewa · 发表于 2012-2-9 18:00

解决了，原来是固件版本太低，真是郁闷，同样的拨号信息，现在反而无问题了，
我是再刷了小标高手的最新固件，同样的设置方法
小标高手的最新固件下载地址：http://www.wifi.com.cn/forum/thread-73539-1-1.html

cnyeewa · 发表于 2012-2-9 18:03

设置方法是转自别人的
现将配置发出，给需要的朋友参考！
step 1:
查找3g网卡的usb-serial信息：
putty 登陆：
#cd /etc/usb_modeswitch.d
# grep MF190 *
19d2:0149:# ZTE MF190 (Variant)
19d2:1224:# ZTE MF190
我使用的是下面的那个MF190信息

step 2:
配置user-serial内容
# cd /etc/modules.d
# vi 60-usb-serial -- 不爱好vi的可以使用winscp上传
usbserial vendor=0x19d2 product=0x1224 # ZTE MF190

step 3:
修改/ect/chatscript/3g.chat
ABORT BUSY
ABORT 'NO CARRIER'
ABORT ERROR
REPORT  CONNECT
TIMEOUT 10
""    "AT&F"
OK    "ATE1"
OK    'AT+CGDCONT=1,"IP","$USE_APN"'
SAY    "Calling UMTS/GPRS"
TIMEOUT 30
OK    "ATD*99***1#"
CONNECT ' '
-- 有人使用的不是上述的默认拨号脚本，我也尝试过但是失败了，相反用默认的成功了！

step 4:
network修改
config 'interface' 'loopback'
      option 'ifname' 'lo'
      option 'proto' 'static'
      option 'ipaddr' '127.0.0.1'
      option 'netmask' '255.0.0.0'

config 'interface' 'lan'
      option 'type' 'bridge'
      option 'proto' 'static'
      option 'ipaddr' '192.168.0.1'
      option 'netmask' '255.255.255.0'
-- 因为我需要利用703n的网口连接有线，把它作为AP用，因此修改为如下配置
config 'interface' 'loopback'
      option 'ifname' 'lo'
      option 'proto' 'static'
      option 'ipaddr' '127.0.0.1'
      option 'netmask' '255.0.0.0'

config 'interface' 'wan'
      option 'ifname' 'eth0'
      option 'proto' 'dhcp'
      option 'gateway' '0.0.0.0'

config 'interface' 'wan1'
      option 'ifname' 'eth1'
      option 'proto' '3g'
      option 'apn' '3gnet'
      option 'service' 'umts'
      option 'pppd_options' 'debug'  -- 用来调试，可以删除
      option 'defaultroute' '0' -- 这个是我后加的，如果不加的话，DNS不能加载
      option 'pincode' '1234' -- 这个也是后加的，没有尝试过删除有何效果，反正放在这里成功拨号
      option 'device' '/dev/ttyUSB2' -- 设备信息

step 5：
修改firewall信息
config zone
      option name          wan
      option network       'wan wan1'
      option input          REJECT
      option output          ACCEPT
      option forward       REJECT
      option masq          1
      option mtu_fix       1

重启即可

cnyeewa · 发表于 2012-2-9 18:06

刚才测试了一下，从重启到可以ping通DNS服务器的时候为49秒，相比官方固件需要7分钟的时间真的快了不少

cnyeewa · 发表于 2012-2-10 11:27

写了这么多，都没人捧场，真是郁闷

c600 · 发表于 2012-2-10 17:07

mu351很快连上3G 可是无线有线都无法上网对这个不熟悉无奈有刷回tp原固件拨号慢点还算稳定

账号		自动登录	找回密码
密码			立即注册

(已解决)急救用wr703n+MF190拨号成功却上不了网的问题

请不要胡乱输入以及粘贴、复制等方式灌水

欢迎大家光临恩山无线论坛 /1