【24-01-02】兆能ZN-M2/和目CMIOT-AX18 iStore USB 无wifi 多拨 ipv6 UPNP NAS

tingqin

谢谢分享

Waron

牛 试一试好不好用

不如吃茶去9009

感谢分享

wonderland

真不错，感谢楼主

fry2022

感谢分享

aaa69532

没改内存256m的能带动不？好用不

215179683

非常完美，两根网线接到wifi6 路由器上，每个口一个网段。 笔记本wifi6 2.4g 复制2个文件（分两条线路走） 150M/s 没有到200M，和目cpu占用50%左右 。 单个文件 走任意一根网线都是111M/s。wifi6路由器cpu 不占用。链路聚合 好像没作用，搞了好久，bond两条网线（有一次设置成功了 但是传输速度只有千兆的一半，而且搞的wifi6路由器cpu占用70%以上 ），wifi6 路由器只有2个网卡eth0 和eth1 。和目是有4个网卡的每一个口对应一个。 led灯也可以全关了 舒服多了。温度也低了。

jfzzq

刚发现会跳挂载为sdb1了。   
现在在磁盘管理有看到个sda，但挂载点 没看到挂载成功  


希望大佬修复硬盘挂载问题 就完美了

jfzzq

拔 插usb 已挂载上sda1   日志如下


[ 1083.537430] nss-dp 3a001600.dp4 eth3: PHY Link is down
[ 1083.537765] br-lan: port 3(eth3) entered disabled state
[ 1098.719964] xhci-hcd xhci-hcd.0.auto: port 0 resume PLC timeout
[ 1102.747382] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
[ 1119.937532] usb 2-1: new SuperSpeed USB device number 10 using xhci-hcd
[ 1119.959729] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 1119.965271] usb-storage 2-1:1.0: Quirks match for vid 174c pid 55aa: 400000
[ 1119.965351] scsi host4: usb-storage 2-1:1.0
[ 1120.969189] scsi 4:0:0:0: Direct-Access     ST4000VN 008-2DR166       0    PQ: 0 ANSI: 6
[ 1120.969878] sd 4:0:0:0: Attached scsi generic sg0 type 0
[ 1120.976397] sd 4:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 1120.981845] sd 4:0:0:0: [sda] 4096-byte physical blocks
[ 1120.989689] sd 4:0:0:0: [sda] Write Protect is off
[ 1120.994312] sd 4:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 1120.994560] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1121.425198]  sda: sda1
[ 1121.427612] sd 4:0:0:0: [sda] Attached SCSI disk
[ 1154.890702] EXT4-fs (sda1): recovery complete
[ 1154.950866] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
[ 1213.549452] nss-dp 3a001600.dp4 eth3: PHY Link up speed: 1000
[ 1213.549539] br-lan: port 3(eth3) entered forwarding state
[ 1213.554265] br-lan: port 3(eth3) entered forwarding state
[ 1215.549406] br-lan: port 3(eth3) entered forwarding state
[ 1223.559623] nss-dp 3a001600.dp4 eth3: PHY Link is down
[ 1223.559894] br-lan: port 3(eth3) entered disabled state
[ 1224.559657] nss-dp 3a001600.dp4 eth3: PHY Link up speed: 1000
[ 1224.559896] br-lan: port 3(eth3) entered forwarding state
[ 1224.564427] br-lan: port 3(eth3) entered forwarding state
[ 1226.559594] br-lan: port 3(eth3) entered forwarding state
[ 1273.230498] usb 2-1: reset SuperSpeed USB device number 10 using xhci-hcd
[ 1273.600513] usb 2-1: reset SuperSpeed USB device number 10 using xhci-hcd
[ 1276.690577] usb 2-1: reset SuperSpeed USB device number 10 using xhci-hcd
[ 1276.710748] usb 2-1: device descriptor read/8, error -71
[ 1276.820462] usb 2-1: reset SuperSpeed USB device number 10 using xhci-hcd
[ 1276.840693] usb 2-1: device descriptor read/8, error -71
[ 1276.950509] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 1276.950567] usb usb2-port1: cannot disable (err = -32)
[ 1277.130577] usb 2-1: reset SuperSpeed USB device number 10 using xhci-hcd
[ 1280.990661] usb 2-1: reset SuperSpeed USB device number 10 using xhci-hcd
[ 1282.210688] usb 2-1: reset SuperSpeed USB device number 10 using xhci-hcd
[ 1283.620662] usb 2-1: reset SuperSpeed USB device number 10 using xhci-hcd
[ 1284.570744] usb 2-1: reset SuperSpeed USB device number 10 using xhci-hcd
[ 1284.590817] usb 2-1: device descriptor read/8, error -71
[ 1284.700584] usb 2-1: reset SuperSpeed USB device number 10 using xhci-hcd
[ 1284.720816] usb 2-1: device descriptor read/8, error -71
[ 1284.830625] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 1284.830716] usb usb2-port1: cannot disable (err = -32)
[ 1285.010720] usb 2-1: reset SuperSpeed USB device number 10 using xhci-hcd

jfzzq

yipush 发表于 2023-7-30 21:02
插上有日志吗，我传了个230730的版本，你试试这个？

您好 刚启动sata硬盘可以挂载 但过几分钟就没了。请看日志

215179683

现在用手搓帖子的，带wifi的固件 温度太高，而且led 有1个无法关闭太亮了。  试下新的

jh3274

让我来试试看

Alone258369

感谢分享     

jfzzq

请问 在openwrt系统 直接刷bin吗？ 还是得先刷UBI

prolae

开启多拨后  任何保持并应用操作都会卡在“正在更改应用 /ect/config/mwan3"这个界面