|
|
本帖最后由 olsl 于 2024-9-20 06:15 编辑
感谢分享,55块淘了一个,试试这个,
用MTK救砖工具在BOOtmenu下更新了FIP后,,失败,用救砖工具刷不上UBOOT,在TTL控制台刷不上,,第一次可以进到UBOOT的界面,在UBOOT界面http://192.168.1.1/uboot.html这里更新UBOOT也不行,重启还是进入那个固件恢复界面!
按流程操作进入的还是TPLINK的软件升级界面,上传openwrt固件显示升级失败.....，是UBOOT没有刷上吗！,
期待大神解决一下啊
Xshell 7 (Build 0169)
Copyright (c) 2020 NetSarang Computer, Inc. All rights reserved.
Type `help' to learn how to use Xshell prompt.
[C:\~]$
Connecting to COM4...
Connected.
Hit any key to stop autoboot: 0
MT7981> bootmenu
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade single image
6. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
*** Upgrading ATF FIP ***
Available load methods:
0 - TFTP client (Default)
1 - Xmodem
2 - Ymodem
3 - Kermit
4 - S-Record
5 - RAM
Select (enter for default): 0
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.50
Input IP netmask: 255.255.255.0
Input file name: ct3003.bin
Using ethernet@15100000 device
TFTP from server 192.168.1.50; our IP address is 192.168.1.1
Filename 'ct3003.bin'.
Load address: 0x46000000
Loading: T ##################################################
8.9 MiB/s
done
Bytes transferred = 730337 (b24e1 hex)
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
*** Loaded 730337 (0xb24e1) bytes at 0x46000000 ***
Erasing from 0x0 to 0xbffff, size 0xc0000 ... OK
Writing from 0x46000000 to 0x0, size 0xb24e1 ... OK
Verifying from 0x0 to 0xb24e0, size 0xb24e1 ... OK
*** ATF FIP upgrade completed! ***
MT7981> bootmenu
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade single image
6. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
*** Upgrading ATF FIP ***
Available load methods:
0 - TFTP client (Default)
1 - Xmodem
2 - Ymodem
3 - Kermit
4 - S-Record
5 - RAM
Select (enter for default): 0
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.50
Input IP netmask: 255.255.255.0
Input file name: ct3003.bin
Using ethernet@15100000 device
TFTP from server 192.168.1.50; our IP address is 192.168.1.1
Filename 'ct3003.bin'.
Load address: 0x46000000
Loading: T ##T T T T T T T T T T T T ################################################
66.4 KiB/s
done
Bytes transferred = 730337 (b24e1 hex)
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
*** Loaded 730337 (0xb24e1) bytes at 0x46000000 ***
Erasing from 0x0 to 0xbffff, size 0xc0000 ... OK
Writing from 0x46000000 to 0x0, size 0xb24e1 ... OK
Verifying from 0x0 to 0xb24e0, size 0xb24e1 ... OK
*** ATF FIP upgrade completed! ***
MT7981> bootmenu
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade single image
6. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
*** Upgrading ATF FIP ***
Available load methods:
0 - TFTP client (Default)
1 - Xmodem
2 - Ymodem
3 - Kermit
4 - S-Record
5 - RAM
Select (enter for default): 0
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.50
Input IP netmask: 255.255.255.0
Input file name: ct3003.bin
Using ethernet@15100000 device
TFTP from server 192.168.1.50; our IP address is 192.168.1.1
Filename 'ct3003.bin'.
Load address: 0x46000000
Loading: T ##################################################
12.7 MiB/s
done
Bytes transferred = 730337 (b24e1 hex)
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
*** Loaded 730337 (0xb24e1) bytes at 0x46000000 ***
Erasing from 0x0 to 0xbffff, size 0xc0000 ... OK
Writing from 0x46000000 to 0x0, size 0xb24e1 ... OK
Verifying from 0x0 to 0xb24e0, size 0xb24e1 ... OK
*** ATF FIP upgrade completed! ***
MT7981> reset
resetting ...
F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 0153 [010F]
Jump to BL
NOTICE: BL2: v2.6(release):220607_wma301v2_r3-dirty
NOTICE: BL2: Built : 08:46:25, Jun 2 2022
NOTICE: WDT: disabled
NOTICE: EMI: Using DDR3 settings
dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000
dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a003f1 000000ff 00100000 00000000
1001d040 | 00027e71 000200a0 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0xc
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 532, worse bit 0, min window 64
Window Sum 528, worse bit 8, min window 64
Window Sum 392, worse bit 2, min window 46
Window Sum 390, worse bit 13, min window 46
NOTICE: EMI: Detected DRAM size: 256MB
NOTICE: EMI: complex R/W mem test passed
NOTICE: CPU: MT7981 (1300MHz)
NOTICE: SPI_NAND parses attributes from parameter page.
NOTICE: SPI_NAND Detected ID 0x85
NOTICE: Page size 2048, Block size 131072, size 134217728
NOTICE: BL2: Booting BL31
NOTICE: BL31: v2.6(release):220607_wma301v2_r3-dirty
NOTICE: BL31: Built : 08:46:25, Jun 2 2022
NOTICE: Hello BL31!!!
U-Boot 2022.04-rc1 (Jun 02 2022 - 08:46:25 +0000)
CPU: MediaTek MT7981
Model: mt7981-rfb
DRAM: 256 MiB
Core: 32 devices, 13 uclasses, devicetree: embed
Loading Environment from MTD... spi-nand: spi_nand spi_nand@0: GigaDevice SPI NAND was found.
spi-nand: spi_nand spi_nand@0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
OK
In: serial@11002000
Out: serial@11002000
Err: serial@11002000
Could not find a valid device for nmbm0
'spi-nand0' is now active device
Reading from 0x4000000 to 0x4000007, size 0x8 ...
Succeeded
Dual image validation, to check image_1 now
Reading from 0x800000 to 0x8000cf, size 0xd0 ...
Succeeded
Image_1 check failed, to check image_2 now
Reading from 0x4800000 to 0x48000cf, size 0xd0 ...
Succeeded
Firmware check failed! Enter recovery mode.
eth0: ethernet@15100000
HTTP server is ready!
Reading from 0x400000 to 0x41ffff, size 0x20000 ...
Succeeded
error: factory info header magic not correct
local info init failed, exit
Attaching option 01 to list
Attaching option 03 to list
Attaching option 06 to list
file: lib_uip/apps/dhcpd/dhcpd.c,line: 873==:dhcpd init OK. --debug by HouXB
HTTP server is starting at IP: 192.168.1.1
file: lib_uip/lib_uip.c,line: 117==:uip set a8c0-101. --debug by HouXB
file: lib_uip/lib_uip.c,line: 132==:start infinite loop! --debug by HouXB
rport:51985; Request for: /favicon.ico
## Error: file not found!
rport:58897; Request for: /favicon.ico
## Error: file not found!
rport:59665; Request for: /favicon.ico
## Error: file not found!
rport:59921; Request for: /favicon.ico
## Error: file not found!
rport:60177; Request for: /
rport:60433; Request for: /logo.png
Option found code 0x35; str: 01
Option found code 0x35; str: 01
Received DISCOVER
Option found code 0x0C; str: 50432d32303231313031365a554957
Broadcasting packet to client
Option found code 0x35; str: 03
Option found code 0x36; str: c0a80101
Option found code 0x32; str: c0a8010c
Option found code 0x35; str: 03
Received REQUESTBroadcasting packet to client
Option found code 0x0C; str: 50432d32303231313031365a554957
rport:19228; Request for: /favicon.ico
## Error: file not found!
rport:24092; Request for: /
rport:24348; Request for: /logo.png
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看，没有账号？立即注册
×
|
楼主: fry2022
/1 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2024-8-28 16:38
显身卡
