HIWIFI极路由已经复制在tp 743n上并成功启动运行

chka***

早些时候，偶然得到一个新路由玩——HIWIFI极路由，该路由有一些比较有特色的加速，挺吸引我的，所以立即决定买了一台工程机来玩。我曾在数码之家首发了一个拆机贴，链接就不贴了，后来看到已经有人帮我转到本坛了，就没有在这里重复发帖了。

拆机转贴：https://www.right.com.cn/forum/thread-120478-1-1.html

从上次拆完机，就一直想能不能克隆到相同硬件的机器上运行。上周末，正好下雨，闲的没事，折腾起这个路由来。

极路由硬件硬件方案是：
CPU：AR9331  400mhz
内存：64M  DDR1代
FLASH：16MBwinbond25Q128BVFG
板载一个8G的缓存（其实就是一个U盘）

手里正好有个TPlink的743N v2，cpu相同，4M/32M的闪存和内存。应该可以通过硬改实现和极路由达到相同的条件。然后就把743N的内存改成64M，flash从极路由固件复制过来，usb口上插了一个8g U盘。上电开机，不能正常启动，卡在半截，后来改了一颗电阻，终于正常启动了，但是有个BUG,就是有线网口的指示灯不正常，不插线是常亮，插网线闪烁，这个是小问题，我曾经应该过740n的灯不难，也就没管它了。

启动后要复位一下，因为会自动格式化u盘，并放进相关文件。

可能有人想要这个机器的编程器固件，但是因为这个固件里有一些信息是用来给云服务器做验证的，为了不影响我自己使用，所以暂时还不能提供给大家。过段时间我会发出来一个去掉验证信息的固件，可能只能单机运行，没有宣传的那些需要云服务器支持的功能。

我把TTL信息发上来，供大家研究：（放楼下吧，这里放不下了）

先到这吧，睡觉去。

http://yunpan.cn/QTMfVnfVRm6aJ （提取码：e919）

chka***

1. U-Boot 1.1.4 (Apr  8 2013 - 23:57:04)
   
2. 
   
3. AP121 (ar9331) U-boot
   
4. 
   
5. DRAM:  64 MB
   
6. Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
   
7. flash size 16777216, sector count = 256
   
8. Flash: 16 MB
   
9. Using default environment
   
10. 
    
11. In:    serial
    
12. Out:   serial
    
13. Err:   serial
    
14. Net:   ag7240_enet_initialize...
    
15. No valid address in Flash. Using fixed address
    
16. No valid address in Flash. Using fixed address
    
17. ag7240 gmac: cfg1 0x5 cfg2 0x7114
    
18. eth0: 00:de:ad:be:ef:32
    
19. eth0 up
    
20. ag7240 gmac: cfg1 0xf cfg2 0x7214
    
21. eth1: 00:de:ad:be:ef:32
    
22. athrs26_reg_init_lan
    
23. ATHRS26: resetting s26
    
24. ATHRS26: s26 reset done
    
25. eth1 up
    
26. eth0, eth1
    
27. Autobooting in 2 seconds
    
28. ## Booting image at 9f020000 ...
    
29.    Image Name:   tw150v1-Linux-3.3.8
    
30.    Created:      2013-04-09  12:23:54 UTC
    
31.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
    
32.    Data Size:    982813 Bytes = 959.8 kB
    
33.    Load Address: 80060000
    
34.    Entry Point:  80060000
    
35.    Verifying Checksum at 0x9f020040 ...OK
    
36.    Uncompressing Kernel Image ... OK
    
37. 
    
38. Starting kernel ...
    
39. 
    
40. [    0.000000] Linux version 3.3.8 (kai.li@WEB-9-1-43) (gcc version 4.6.4 20121001 (prerelease) (Linaro GCC 4.6-2012.10) ) #1 Tue Apr 9 00:09:58 CST 2013
    
41. [    0.000000] bootconsole [early0] enabled
    
42. [    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
    
43. [    0.000000] SoC: Atheros AR9330 rev 1
    
44. [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
    
45. [    0.000000] Determined physical RAM map:
    
46. [    0.000000]  memory: 04000000 @ 00000000 (usable)
    
47. [    0.000000] Initrd not found or empty - disabling initrd
    
48. [    0.000000] Zone PFN ranges:
    
49. [    0.000000]   Normal   0x00000000 -> 0x00004000
    
50. [    0.000000] Movable zone start PFN for each node
    
51. [    0.000000] Early memory PFN ranges
    
52. [    0.000000]     0: 0x00000000 -> 0x00004000
    
53. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
    
54. [    0.000000] Kernel command line:  board=HC6361 console=ttyATH0,115200 mtdparts=spi0.0:64k(u-boot),64k(bdinfo)ro,1280k(kernel),14848k(rootfs),64k(nvram),64k(art)ro,16128k@0x20000(firmware) rootfstype=squashfs,jffs2 noinitrd
    
55. [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
    
56. [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
    
57. [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
    
58. [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    
59. [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
    
60. [    0.000000] Writing ErrCtl register=00000000
    
61. [    0.000000] Readback ErrCtl register=00000000
    
62. [    0.000000] Memory: 61516k/65536k available (2106k kernel code, 4020k reserved, 537k data, 176k init, 0k highmem)
    
63. [    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    
64. [    0.000000] NR_IRQS:51
    
65. [    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
    
66. [    0.080000] pid_max: default: 32768 minimum: 301
    
67. [    0.080000] Mount-cache hash table entries: 512
    
68. [    0.090000] NET: Registered protocol family 16
    
69. [    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
    
70. [    0.100000] MIPS: machine is Turbo Wireless TW150V1 Board
    
71. [    0.550000] bio: create slab <bio-0> at 0
    
72. [    0.560000] Switching to clocksource MIPS
    
73. [    0.560000] NET: Registered protocol family 2
    
74. [    0.570000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    
75. [    0.570000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
    
76. [    0.570000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
    
77. [    0.580000] TCP: Hash tables configured (established 2048 bind 2048)
    
78. [    0.590000] TCP reno registered
    
79. [    0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
    
80. [    0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
    
81. [    0.600000] NET: Registered protocol family 1
    
82. [    0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    
83. [    0.630000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
    
84. [    0.640000] msgmni has been set to 120
    
85. [    0.640000] io scheduler noop registered
    
86. [    0.650000] io scheduler deadline registered (default)
    
87. [    0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
    
88. [    0.660000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
    
89. [    0.660000] console [ttyATH0] enabled, bootconsole disabled
    
90. [    0.660000] console [ttyATH0] enabled, bootconsole disabled
    
91. [    0.680000] m25p80 spi0.0: found w25q128, expected m25p80
    
92. [    0.680000] m25p80 spi0.0: w25q128 (16384 Kbytes)
    
93. [    0.690000] 7 cmdlinepart partitions found on MTD device spi0.0
    
94. [    0.690000] Creating 7 MTD partitions on "spi0.0":
    
95. [    0.700000] 0x000000000000-0x000000010000 : "u-boot"
    
96. [    0.710000] 0x000000010000-0x000000020000 : "bdinfo"
    
97. [    0.710000] 0x000000020000-0x000000160000 : "kernel"
    
98. [    0.720000] 0x000000160000-0x000000fe0000 : "rootfs"
    
99. [    0.720000] mtd: partition "rootfs" set to be root filesystem
    
100. [    0.730000] mtd: partition "rootfs_data" created automatically, ofs=6D0000, len=910000
     
101. [    0.730000] 0x0000006d0000-0x000000fe0000 : "rootfs_data"
     
102. [    0.740000] 0x000000fe0000-0x000000ff0000 : "nvram"
     
103. [    0.750000] 0x000000ff0000-0x000001000000 : "art"
     
104. [    0.750000] 0x000000020000-0x000000fe0000 : "firmware"
     
105. [    0.760000] ar933x_spiop_ioc: init
     
106. [    0.780000] ag71xx_mdio: probed
     
107. [    0.780000] eth0: Atheros AG71xx at 0xba000000, irq 5
     
108. [    1.340000] eth0: Found an AR7240/AR9330 built-in switch
     
109. [    2.370000] eth1: Atheros AG71xx at 0xb9000000, irq 4
     
110. [    2.920000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
     
111. [    2.930000] TCP cubic registered
     
112. [    2.930000] NET: Registered protocol family 17
     
113. [    2.940000] 8021q: 802.1Q VLAN Support v1.8
     
114. [    2.940000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
     
115. [    2.950000] Freeing unused kernel memory: 176k freed
     
116. - preinit -
     
117. Press the [f] key and hit [enter] to enter failsafe mode
     
118. - regular preinit -
     
119. [   10.420000] JFFS2 notice: (422) jffs2_build_xattr_subsystem: complete building xattr subsystem, 25 of xdatum (0 unchecked, 25 orphan) and 55 of xref (0 dead, 55 orphan) found.
     
120. switching to jffs2
     
121. - init -
     
122. [   11.690000] NET: Registered protocol family 10
     
123. [   12.040000] SCSI subsystem initialized
     
124. [   12.220000] usbcore: registered new interface driver usbfs
     
125. [   12.220000] usbcore: registered new interface driver hub
     
126. [   12.230000] usbcore: registered new device driver usb
     
127. [   12.620000] ath_hal: 0.9.17.1 (AR9330)
     
128. [   12.680000] hcwifi 1.1.1.553n
     
129. [   13.110000] loop: module loaded
     
130. [   13.320000] PPP generic driver version 2.4.2
     
131. [   13.370000] IPv4 over IPv4 tunneling driver
     
132. [   13.400000] IPv6 over IPv4 tunneling driver
     
133. [   13.870000] ip_tables: (C) 2000-2006 Netfilter Core Team
     
134. [   14.140000] NET: Registered protocol family 24
     
135. [   14.350000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
     
136. [   14.350000] ehci-platform ehci-platform: Generic Platform EHCI Controller
     
137. [   14.360000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
     
138. [   14.400000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
     
139. [   14.420000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
     
140. [   14.420000] hub 1-0:1.0: USB hub found
     
141. [   14.420000] hub 1-0:1.0: 1 port detected
     
142. [   14.550000] nf_conntrack version 0.5.0 (963 buckets, 3852 max)
     
143. [   14.900000] usb 1-1: new high-speed USB device number 2 using ehci-platform
     
144. [   15.600000] xt_time: kernel timezone is -0000
     
145. [   16.240000] Initializing USB Mass Storage driver...
     
146. [   16.240000] scsi0 : usb-storage 1-1:1.0
     
147. [   16.250000] usbcore: registered new interface driver usb-storage
     
148. [   16.250000] USB Mass Storage support registered.
     
149. [   17.250000] scsi 0:0:0:0: Direct-Access     EAGET    F30              1.00 PQ: 0 ANSI: 5
     
150. [   17.260000] sd 0:0:0:0: [sda] 15155200 512-byte logical blocks: (7.75 GB/7.22 GiB)
     
151. [   17.260000] sd 0:0:0:0: [sda] Write Protect is off
     
152. [   17.270000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
     
153. [   17.570000]  sda: unknown partition table
     
154. [   17.580000] sd 0:0:0:0: [sda] Attached SCSI removable disk
     
155. [   21.490000] ADDRCONF(NETDEV_UP): eth0: link is not ready
     
156. [   22.550000] ADDRCONF(NETDEV_UP): eth0: link is not ready
     
157. [   22.550000] device eth0 entered promiscuous mode
     
158. [   22.570000] ADDRCONF(NETDEV_UP): br-lan: link is not ready
     
159. [   22.600000] ADDRCONF(NETDEV_UP): eth1: link is not ready
     
160. [   26.020000] device wlan0 entered promiscuous mode
     
161. [   26.030000] br-lan: port 2(wlan0) entered forwarding state
     
162. [   26.030000] br-lan: port 2(wlan0) entered forwarding state
     
163. [   26.040000] ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
     
164. [   26.510000] core_vap_start: wlan0 start
     
165. [   26.540000] ath_paprd_cal: PAPRD done channel 2412
     
166. [   28.030000] br-lan: port 2(wlan0) entered forwarding state
     
167. [   43.170000] EXT4-fs (sda): mounting ext3 file system using the ext4 subsystem
     
168. [   43.190000] EXT4-fs (sda): mounted filesystem with ordered data mode. Opts: (null)
     
169. [   43.500000] Adding 65532k swap on /tmp/sda/.swap.  Priority:-1 extents:6 across:69696k
     
170. Apr 13 10:09:48 crond[1533]: crond: crond (busybox 1.19.4) started, log level 5

复制代码

xtw***

高手 来支持一下

ZHIZ***

期待楼主发固件。

ff88***

支持一下                             

lia***

好象很不错呀

laom***

[catsoul=4]这真是极好的[/catsoul]

cmh***

下一版又要改验证了

cmh***

好奇你的U盘怎么是这么个体位？

chao***

牛B大了。。。

modi***

[catsoul=5]这个改造够牛逼的[/catsoul]

秦时***

关注!{:soso__14595186475676886815_1:}

chka***

cmheia 发表于 2013-6-19 13:49
好奇你的U盘怎么是这么个体位？

呵呵，tplink的743和843都是这个体位。

雷***

支持一下，要是能改成把整个系统可以移植到u盘flash当做引导就好

不知道ar9344以后有没有破解

---

骄傲的使用Chrome

Powered By Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.31 (KHTML, like Gecko) Chrome/26.0.1410.64 Safari/537.31

tzxi***

真是大神，只能仰望