|
楼主 |
发表于 2013-6-18 20:00
|
显示全部楼层
第二次,没启动起来,4LAN灯加系统灯亮,没反映。
U-Boot 1.1.4 (Aug 27 2011 - 10:39:39)
AP121-2MB (ar9330) U-boot
DRAM: 64 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.3.3 (zeaxion@zeaxion-desktop) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Mon May 21 17:13:10 CST 2012
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-WR741ND-v4 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61776k/65536k available (2087k kernel code, 3760k reserved, 399k data, 200k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:48
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
[ 0.540000] bio: create slab <bio-0> at 0
[ 0.540000] Switching to clocksource MIPS
[ 0.550000] NET: Registered protocol family 2
[ 0.550000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.560000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.570000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.570000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.580000] TCP reno registered
[ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.590000] NET: Registered protocol family 1
[ 0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.620000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.630000] msgmni has been set to 120
[ 0.630000] io scheduler noop registered
[ 0.640000] io scheduler deadline registered (default)
[ 0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.650000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.660000] console [ttyATH0] enabled, bootconsole disabled
[ 0.660000] console [ttyATH0] enabled, bootconsole disabled
[ 0.670000] m25p80 spi0.0: found s25fl064k, expected m25p80
[ 0.670000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.680000] 5 tp-link partitions found on MTD device spi0.0
[ 0.680000] Creating 5 MTD partitions on "spi0.0":
[ 0.690000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.690000] 0x000000020000-0x0000000fd8e0 : "kernel"
[ 0.700000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.710000] 0x0000000fd8e0-0x0000007f0000 : "rootfs"
[ 0.720000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.730000] mtd: partition "rootfs" set to be root filesystem
[ 0.730000] mtd: partition "rootfs_data" created automatically, ofs=6C0000, len=130000
[ 0.740000] 0x0000006c0000-0x0000007f0000 : "rootfs_data"
[ 0.750000] 0x0000007f0000-0x000000800000 : "art"
[ 0.750000] 0x000000020000-0x0000007f0000 : "firmware"
[ 1.000000] ag71xx_mdio: probed
[ 1.000000] eth0: Atheros AG71xx at 0xba000000, irq 5
[ 1.590000] eth0: Found an AR7240/AR9330 built-in switch
[ 2.820000] eth1: Atheros AG71xx at 0xb9000000, irq 4
[ 3.430000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 3.430000] TCP westwood registered
[ 3.440000] NET: Registered protocol family 17
[ 3.440000] 8021q: 802.1Q VLAN Support v1.8
[ 3.450000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 3.460000] Freeing unused kernel memory: 200k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 10.590000] JFFS2 notice: (424) jffs2_build_xattr_subsystem: complete building xattr subsystem, 3 of xdatum (1 unchecked, 2 orphan) and 109 of xref (0 dead, 78 orphan) found.
switching to jffs2
- init -
Please press Enter to activate this console. [ 13.630000] Compat-wireless backport release: compat-wireless-2012-04-17-1-r31449
[ 13.630000] Backport based on wireless-testing.git master-2012-04-17
[ 13.670000] cfg80211: Calling CRDA to update world regulatory domain
[ 14.210000] cfg80211: World regulatory domain updated:
[ 14.210000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 14.220000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.220000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 14.230000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 14.240000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.250000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.530000] SCSI subsystem initialized
[ 14.790000] usbcore: registered new interface driver usbfs
[ 14.800000] usbcore: registered new interface driver hub
[ 14.800000] usbcore: registered new device driver usb
[ 15.630000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 15.630000] cfg80211: Calling CRDA for country: US
[ 15.650000] Button Hotplug driver version 0.4.1
[ 15.830000] cfg80211: Regulatory domain changed to country: US
[ 15.840000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.850000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 15.850000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 15.860000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.870000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.880000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.880000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 16.660000] PPP generic driver version 2.4.2
[ 16.700000] PPP MPPE Compression module registered
[ 16.940000] GRE over IPv4 demultiplexor driver
[ 16.970000] GRE over IPv4 tunneling driver
[ 17.370000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 17.670000] NET: Registered protocol family 24
[ 17.950000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.960000] ath79-ehci ar933x-ehci: Atheros built-in EHCI controller
[ 17.960000] ath79-ehci ar933x-ehci: new USB bus registered, assigned bus number 1
[ 18.000000] ath79-ehci ar933x-ehci: irq 3, io mem 0x1b000000
[ 18.020000] ath79-ehci ar933x-ehci: USB 2.0 started, EHCI 1.00
[ 18.020000] hub 1-0:1.0: USB hub found
[ 18.020000] hub 1-0:1.0: 1 port detected
[ 18.060000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)
[ 18.560000] usb 1-1: new full-speed USB device number 2 using ath79-ehci
[ 19.150000] usb 1-1: device descriptor read/64, error -71
[ 19.490000] xt_time: kernel timezone is -0000
[ 19.630000] usb 1-1: device descriptor read/64, error -71
[ 19.900000] usb 1-1: new full-speed USB device number 3 using ath79-ehci
[ 20.040000] xt_opendpi 0.1 (OpenDPI wrapper module).
[ 20.150000] arp_tables: (C) 2002 David S. Miller
[ 20.480000] usb 1-1: device descriptor read/64, error -71
[ 20.590000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 20.680000] uhci_hcd: USB Universal Host Controller Interface driver
[ 21.080000] usbcore: registered new interface driver usbserial
[ 21.080000] USB Serial support registered for generic
[ 21.130000] usb 1-1: device descriptor read/64, error -71
[ 21.360000] usb 1-1: new full-speed USB device number 4 using ath79-ehci
[ 21.840000] usb 1-1: device not accepting address 4, error -71
[ 21.960000] usb 1-1: new full-speed USB device number 5 using ath79-ehci
|
|