|
|
本帖最后由 antons 于 2014-11-12 14:07 编辑
MT7620 64M 内存 8M FLASH 11200mah三星18650电池 USB接口一个 WAN一个 可以刷OP固件 外出携带必备啊
价格100+ 绝对比703N 实惠哦 估计又一新神器了
2.19补充
原机固件可TELNET
2.25补充 OP固件实测成功
2.26补充：如意云成功刷入，完美运行
TTL定义 自上而下
TX RX GND
提示 ：为防止直写编程器固件导致无线下降 请参考以下帖子 备份EEPROM 必要时恢复即可
PS: op固件下恢复 需指定本机IP 192.168.1.5
原版固件可TELNET 192.168.100.1 即可运行命令
https://www.right.com.cn/forum/forum.php?mod=viewthread&tid=132462
原机的UBOOT也不行 请直接刷入提供的X8专用编程器固件 （原厂为8M FLASH ）
SYS灯定义有问题 暂时不能正常工作 WLAN灯正常 LAN灯正常
考虑可能有人不小心搞坏焊盘 提供高清大图
将编程器固件刷入后 可以直接运行 网口为WAN WIFI名称为pandorabox
所有文件下载处：
校对工具，原厂编程器固件，8M FLASH编程器刷OP编程器固件 16M FLASH编程器刷OP编程器固件
http://pan.baidu.com/s/1o6G3jAi
更新华硕N14U 精简版固件 8M FLASH可刷 http://bbs.xcloud.cc/forum.php?mod=viewthread&tid=3582&extra=page%3D3
原机TTL信息如下
U-Boot 1.1.3 (Jan 7 2013 - 11:32:07)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 7 2013 Time:11:32:07
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 4508895 Bytes = 4.3 MB
Load Address: 80000000
Entry Point: 8000c310
raspi_read: from:50040 len:44ccdf
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c310) ...
## Giving linux memsize in MB, 64
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.36 (root@MaxWong) (gcc version 3.4.2) #368 Tue Aug 6 10:29:57 CST 2013
The CPU feqenuce set to 580 MHz
MIPS CPU sleep mode enabled.
PCIE: bypass PCIe DLL.
PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
disable all power about PCIe
PCIE: PLL power down for MT7620N
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0001ffb8
Readback ErrCtl register=0001ffb8
Memory: 56628k/65536k available (4324k kernel code, 8908k reserved, 839k data, 2896k init, 0k highmem)
NR_IRQS:128
MTK/Ralink System Tick Counter init... cd:804edf18, m:214748, s:32
Console: colour dummy device 80x25
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource Ralink external timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.29 [Flags: R/W].
fuse init (API version 7.15)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
deice id : c8 40 17 c8 40 (4017c840)
maxflash(c8 4017c840) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
Creating 4 MTD partitions on "raspi":
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000800000 : "Kernel"
rdm_major = 253
SMACCR1 -- : 0x00008c88
SMACCR0 -- : 0x2b000004
Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500!
SMACCR1 -- : 0x00008c88
SMACCR0 -- : 0x2b000004
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
=== pAd = c0105000, size = 711224 ===
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.5
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
i8042.c: i8042 controller self test timeout.
Trying to free nonexistent resource <0000000000000060-000000000000006f>
mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nf_conntrack version 0.5.0 (884 buckets, 3536 max)
nf_conntrack_rtsp v0.6.21 loading
matchsize=264
xt_time: kernel timezone is -0000
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
_nvram_read checksum = 3c6e save checksum = 3c6e
Freeing unused kernel memory: 2896k freed
Hit enter to continue...7620.
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=81000c0
switch reg write offset=2110, value=81000c0
switch reg write offset=2210, value=81000c0
switch reg write offset=2310, value=81000c0
switch reg write offset=2410, value=81000c0
switch reg write offset=2510, value=81000c0
switch reg write offset=2610, value=8100000
switch reg write offset=2710, value=8100000
switch reg write offset=26Raeth v3.0 (04Tasklet, ,SkbRecyclev)
alue=
phy_tx_ring = 0x02eeb000, tx_ring = 0xa2eeb000
phy_rx_ring0 = 0x02eec000, rx_ring0 = 0xa2eec000
SMACCR1 -- : 0x00008c88
SMACCR0 -- : 0x2b000004
20CDMA_CSG_CFG = 81000000
ffGDMA1_FWD_CFG = 20710000
0003
switch reg write offset=2704, value=20ff0003
switch reg write offset=2610, value=81000000
switch reg write offset=2014, value=10001
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314,Algorithmics/MIPS FPU Emulator v1.5
value=10001
switch reg write offset=2414, value=10002
switch reg write offset=2514, value=10001
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
RX DESC a2dbb000 size = 2048
RTMP_TimerListAdd: add timer obj c0175d70!
RTMP_TimerListAdd: add timer obj c0141e40!
RTMP_TimerListAdd: add timer obj c0142290!
RTMP_TimerListAdd: add timer obj c0142324!
RTMP_TimerListAdd: add timer obj c01423b8!
RTMP_TimerListAdd: add timer obj c014244c!
RTMP_TimerListAdd: add timer obj c01424e0!
RTMP_TimerListAdd: add timer obj c0142574!
RTMP_TimerListAdd: add timer obj c0142608!
RTMP_TimerListAdd: add timer obj c014269c!
RTMP_TimerListAdd: add timer obj c0142730!
RTMP_TimerListAdd: add timer obj c01427c4!
RTMP_TimerListAdd: add timer obj c0142858!
RTMP_TimerListAdd: add timer obj c01428ec!
RTMP_TimerListAdd: add timer obj c0142980!
RTMP_TimerListAdd: add timer obj c0142a14!
RTMP_TimerListAdd: add timer obj c0142aa8!
RTMP_TimerListAdd: add timer obj c0142b3c!
RTMP_TimerListAdd: add timer obj c0141e14!
RTMP_TimerListAdd: add timer obj c0142264!
RTMP_TimerListAdd: add timer obj c01422f8!
RTMP_TimerListAdd: add timer obj c014238c!
RTMP_TimerListAdd: add timer obj c0142420!
RTMP_TimerListAdd: add timer obj c01424b4!
RTMP_TimerListAdd: add timer obj c0142548!
RTMP_TimerListAdd: add timer obj c01425dc!
RTMP_TimerListAdd: add timer obj c0142670!
RTMP_TimerListAdd: add timer obj c0142704!
RTMP_TimerListAdd: add timer obj c0142798!
RTMP_TimerListAdd: add timer obj c014282c!
RTMP_TimerListAdd: add timer obj c01428c0!
RTMP_TimerListAdd: add timer obj c0142954!
RTMP_TimerListAdd: add timer obj c01429e8!
RTMP_TimerListAdd: add timer obj c0142a7c!
RTMP_TimerListAdd: add timer obj c0142b10!
RTMP_TimerListAdd: add timer obj c0141de8!
RTMP_TimerListAdd: add timer obj c014c8dc!
RTMP_TimerListAdd: add timer obj c014c9f8!
RTMP_TimerListAdd: add timer obj c014c908!
RTMP_TimerListAdd: add timer obj c0143cbc!
RTMP_TimerListAdd: add timer obj c010a530!
RTMP_TimerListAdd: add timer obj c010b36c!
RTMP_TimerListAdd: add timer obj c010c1a8!
RTMP_TimerListAdd: add timer obj c010cfe4!
RTMP_TimerListAdd: add timer obj c010de20!
RTMP_TimerListAdd: add timer obj c010ec5c!
RTMP_TimerListAdd: add timer obj c010fa98!
RTMP_TimerListAdd: add timer obj c01108d4!
RTMP_TimerListAdd: add timer obj c01439cc!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 6
2. Phy Mode = 6
E2PROM: D0 target power=0xff20
E2PROM: 40 MW Power Delta= 0
3. Phy Mode = 6
RTMP_TimerListAdd: add timer obj c010a128!
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = 2, D2 = 9, CalCode = 16 !!!
RT6352_Temperature_Init : BBPR49 = 0x2
RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff8
Current Temperature from BBP_R49=0xffffffeb
TX BW Filter Calibration !!!
RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= f, phase=3d)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 3, phase=3d)
TX IQ Calibration Done!
RXIQ Sigma_i=755, Sigma_q=759, R_iq=-1830
RXIQ calibration FAIL
MCS Set = ff ff 00 00 01
ADC clcok selection for E3 !!!
Shielding clock selection !!!
RTMP_TimerListAdd: add timer obj c014422c!
ADC clcok selection for E3 !!!
Apr clock selection !!!
Main bssid = 78:d3:8d:04:6c:ae
<==== rt28xx_init, Status=0
0x1300 = 00064380
killall: rt2860apd: no process killed
rt2860apd: No such file or directory
device eth2 entered promiscuous mode
device ra0 entered promiscuous mode
br0: port 1(ra0) entering forwarding state
br0: port 1(ra0) entering forwarding state
info, udhcp server (v0.9.8) started
time.windows.com: Unknown host
open error
Open /proc/max/macfilter Failed
Interface doesn't accept private ioctl...
set (8BE2): Invalid argument
Open /proc/max/trackerurl Failed
samba.sh PorayNet WORKGROUP
smbpasswd -a admin admin
startsmbfilepwent_internal: file /etc/smbpasswd did not exist. File successfully created.
Added user admin.
Changing password for admin
Password for admin changed by admin
warning: `proftpd' uses 32-bit capabilities (legacy support in use)
- setting default address to 192.168.100.1
device eth2 left promiscuous mode
device eth2 entered promiscuous mode
IDLE
info, udhcp client (v0.9.8) started
info, Sending discover... (4)
echo (198): /proc/195/oom_adj is deprecated, please use /proc/195/oom_score_adj instead.
Hit enter to continue...info, Sending discover..
可能系统基于OP 可以运行TELNET
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看，没有账号？立即注册
×
评分
-
查看全部评分
|
/1 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2014-2-17 18:54
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
发表于 2014-2-17 19:22
