|
楼主 |
发表于 2014-3-26 22:03
|
显示全部楼层
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- raspi_read: from:50000 len:40
- . Image Name: Linux Kernel Image
- Created: 2013-11-11 6:38:25 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 3060645 Bytes = 2.9 MB
- Load Address: 80000000
- Entry Point: 803bd000
- raspi_read: from:50040 len:2eb3a5
- ............................................... Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 803bd000) ...
- ## Giving linux memsize in MB, 32
- Starting kernel ...
- LINUX started...
- THIS IS ASIC
- Linux version 2.6.21 (root@ubuntu) (gcc version 3.4.2) #242 Mon Nov 11 14:35:28 CST 2013
- The CPU frequency set to 360 MHz
- CPU revision is: 0001964c
- Determined physical RAM map:
- memory: 01000000 @ 00000000 (usable)
- Built 1 zonelists. Total pages: 4064
- Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5
- Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
- Primary data cache 16kB, 4-way, linesize 32 bytes.
- Synthesized TLB refill handler (20 instructions).
- Synthesized TLB load handler fastpath (32 instructions).
- Synthesized TLB store handler fastpath (32 instructions).
- Synthesized TLB modify handler fastpath (31 instructions).
- Cache parity protection disabled
- cause = 40808000, status = 11000000
- PID hash table entries: 64 (order: 6, 256 bytes)
- calculating r4koff... 0015f900(1440000)
- CPU frequency 360.00 MHz
- Using 0.050 MHz high precision timer.
- Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
- Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
- Memory: 12196k/16384k available (3063k kernel code, 4188k reserved, 760k data, 112k init, 0k highmem)
- Mount-cache hash table entries: 512
- NET: Registered protocol family 16
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- NET: Registered protocol family 2
- Time: MIPS clocksource has been installed.
- proc_init_hx_interface
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 512 (order: 0, 4096 bytes)
- TCP bind hash table entries: 512 (order: -1, 2048 bytes)
- TCP: Hash tables configured (established 512 bind 512)
- TCP reno registered
- deice id : c2 20 16 c2 20 (2016c220)
- MX25L3205D(c2 2016c220) (4096 Kbytes)
- mtd .name = raspi, .size = 0x00400000 (4M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
- Creating 7 MTD partitions on "raspi":
- 0x00000000-0x00400000 : "ALL"
- 0x00000000-0x00020000 : "Bootloader"
- 0x00020000-0x00040000 : "Config"
- 0x00040000-0x00050000 : "Factory"
- 0x00050000-0x001833e5 : "Kernel"
- mtd: partition "Kernel" doesn't end on an erase block -- force read-only
- 0x001833e5-0x00800000 : "RootFS"
- mtd: partition "RootFS" extends beyond the end of device "raspi" -- size truncated to 0x27cc1b
- mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only
- 0x00050000-0x00800000 : "Kernel_RootFS"
- mtd: partition "Kernel_RootFS" extends beyond the end of device "raspi" -- size truncated to 0x3b0000
- RT3xxx EHCI/OHCI init.
- squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
- squashfs: LZMA suppport for slax.org by jro
- NTFS driver 2.1.28 [Flags: R/W].
- fuse init (API version 7.8)
- io scheduler noop registered (default)
- ++++++++++++gpio11+++++++++++Ralink gpio driver initialized
- HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
- N_HDLC line discipline registered.
- Serial: 8250/16550 driver $Revision: 1.8 $ 2 ports, IRQ sharing disabled
- serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
- serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
- loop: loaded (max 8 devices)
- usbcore: registered new interface driver ub
- rdm_major = 253
- eth2 mii.o query= phy_id:0, address:1 retval:7849
- Ralink APSoC Ethernet Driver Initilization. v2.1 256 rx/tx descriptors allocated, mtu = 1500!
- MAC_ADRH -- : 0x0000000c
- MAC_ADRL -- : 0x020ae4c4
- PROC INIT OK!
- PPP generic driver version 2.4.2
- PPP BSD Compression module registered
- NET: Registered protocol family 24
- === pAd = c0019000, size = 474896 ===
- <-- RTMPAllocAdapterBlock, Status=0
- block2mtd: version $Revision: 1.1.1.1 $
- rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
- rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
- rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
- rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
- call_usermodehelper: /usr/sbin/usb_link_change up
- usb usb1: Product: Ralink EHCI Host Controller
- usb usb1: Manufacturer: Linux 2.6.21 ehci_hcd
- usb usb1: SerialNumber: rt3xxx
- usb usb1: configuration #1 chosen from 1 choice
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
- rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
- rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
- call_usermodehelper: /usr/sbin/usb_link_change up
- usb usb2: Product: RT3xxx OHCI Controller
- usb usb2: Manufacturer: Linux 2.6.21 ohci_hcd
- usb usb2: SerialNumber: rt3xxx-ohci
- usb usb2: configuration #1 chosen from 1 choice
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 1 port detected
- usbcore: registered new interface driver cdc_acm
- drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
- usbcore: registered new interface driver libusual
- usbcore: registered new interface driver usbserial
- drivers/usb/serial/usb-serial.c: USB Serial Driver core
- drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
- usbcore: registered new interface driver option
- drivers/usb/serial/option.c: USB Driver for GSM modems: Macroinfo: v0.7.1
- drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem (1 port)
- drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem (3 port)
- usbcore: registered new interface driver sierra
- drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.0.6
- hso: drivers/usb/serial/hso.c: 1.6.1-Option Option Wireless Macroinfo
- usbcore: registered new interface driver hso
- nf_conntrack version 0.5.0 (128 buckets, 1024 max)
- ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
- TCP cubic registered
- NET: Registered protocol family 1
- NET: Registered protocol family 17
- 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
- All bugs added by David S. Miller <davem@redhat.com>
- VFS: Mounted root (squashfs filesystem) readonly.
- Freeing unused kernel memory: 112k freed
- init started: BusyBox v1.12.1 (2013-11-11 14:29:21 CST)
- starting pid 640, tty '': '/etc_ro/rcS'
- Algorithmics/MIPS FPU Emulator v1.5
- devpts: called with bogus options
- Welcome to
- ____ _____ _______ _______ _______ ________ __ ____ _ ________ ________
- | \ / || __ | | _____| | ___ \ | ___ | |__| | \ | | | _____| | ___ |
- | |\ \/ /| || |__| | | | | |___| | | | | | __ | \| | | |_____ | | | |
- | | \ / | || _ | | |____ | _ / | |__| | | | | |\ | | _____| | |__| |
- |__| \__/ |__||__| |__| |_______| |__| \__\ |________| |__| |_| \____| |__| |________|
-
- www.macroinfo.com.cn
- 2860:yuxw wapi:yuxw
- rm: cannot remove '/var/run/2860_config': No such file or directory
- crc = 2b1d0c22
- rm: cannot remove '/var/run/wapi_config': No such file or directory
- crc = 63389eb0
- mknod: /dev/nvram: File exists
- cat: can't open '/var/run/TestMode': No such file or directory
- Start ssid modify, default SSID is 3G_WiFi_
- Ver1: hx1.7 Ver2: hx1.7
- <daemon.c> at 130, in main()
- <daemon.c> at 191, in main()
- ssid = 3G_WiFi_
- in internet.sh -----------------start
- ###########################################
- ############internet.sh start##############
- ############00:00:11######
- ############internet.sh start##############
- ###########################################
- Password for 'hongxun' changed
- Password for 'admin' changed
- ssid = 3G_WiFi_
- ls: /dev/sd*: No such file or directory
- ls: /dev/ttyACM*: No such file or directory
- ls: /dev/ttyUSB*: No such file or directory
- rmmod: ralink_wdt: No such file or directory
- rmmod: cls: No such file or directory
- rmmod: hw_nat: No such file or directory
- rmmod: raeth: No such file or directory
- insmod: bridge.ko: module not found
- insmod: mii.ko: module not found
- insmod: raeth.ko: module not found
- phy_tx_ring = 0x0093a000, tx_ring = 0xa093a000
- phy_rx_ring0 = 0x0093b000, rx_ring0 = 0xa093b000
- MAC_ADRH -- : 0x0000000c
- MAC_ADRL -- : 0x020ae4c4
- RT305x_ESW: Link Status Changed
- esw_link_status_changed_event_set entered
- esw_link_status_changed_cb entered
- call_usermodehelper: /usr/sbin/eth_state_check down
- ssid = 3G_WiFi_
- ##### disable 1st wireless interface #####
- rmmod: rt2860v2_ap_net: No such file or directory
- rmmod: rt2860v2_ap: No such file or directory
- rmmod: rt2860v2_ap_util: No such file or directory
- rmmod: rt2860v2_sta_net: No such file or directory
- rmmod: rt2860v2_sta: No such file or directory
- rmmod: rt2860v2_sta_util: No such file or directory
- +++++++++++ Channel = 0insmod: rt2860v2_ap_util.ko: module not found
- insmod: rt2860v2_ap.ko: module not found
- insmod: rt2860v2_ap_net.ko: module not found
- /sbin/internet.sh: line 420: virtual**-passthru.sh: not found
- br0-IP:192.168.169.1
- RX DESC a099f000 size = 2048
- <-- RTMPAllocTxRxRingMemory, Status=0
- Key1Str is Invalid key length(0) or Type(0)
- Key2Str is Invalid key length(0) or Type(0)
- Key3Str is Invalid key length(0) or Type(0)
- Key4Str is Invalid key length(0) or Type(0)
- 1. Phy Mode = 9
- 2. Phy Mode = 9
- TXALC> bInternalTxALC = 0
- 3. Phy Mode = 9
- NICInitAsicFromEEPROM: pAd->TxPowerCtrl.bInternalTxALC = 0
- RTMPSetPhyMode: channel is out of range, use first channel=0
- MCS Set = ff 00 00 00 01
- SYNC - BBP R4 to 20MHz.l
- ##Select Channel 14
- Main bssid = 00:0c:02:00:ab:cd
- <==== rt28xx_init, Status=0
- 0x1300 = 00064380
- vconfig: ioctl error for rem: Invalid argument
- vconfig: ioctl error for rem: Invalid argument
- rmmod: 8021q: No such file or directory
- insmod: 8021q.ko: module not found
- ssid = 3G_WiFi_ABCD
- --- WiFi SSID is:3G_WiFi_ABCD
- starting pid 1173, tty '/dev/ttyS1': '/bin/login'
- HongXun Socket Test V00R01 Beta 001
- (none) login: eth2.2: Setting MAC address to 00 0c 02 00 ab cd.
- device eth2 entered promiscuous mode
- VLAN (eth2.2): Setting underlying device (eth2) to promiscious mode.
- ifconfig: ioctl 0x8913 failed: No such device
- brctl: bridge br0: No such device or address
- iptables v1.3.5: can't initialize iptables table `mangle': Table does not exist (do you need to insmod?)
- Perhaps iptables or your kernel needs to be upgraded.
- ##### config Ralink ESW vlan partition (WLLLL) #####
- done.
- device ra0 entered promiscuous mode
- eth2 mii.o query= phy_id:1, address:4 retval:5e1
- eth2 mii.o query= phy_id:1, address:0 retval:3900
- eth2 mii.o query= phy_id:1, address:5 retval:0
- eth2.1: dev_set_promiscuity(master, 1)
- device eth2.1 entered promiscuous mode
- udhcpc (v1.12.1) started
- br0: port 2(eth2.1) entering learning state
- br0: port 1(ra0) entering learning state
- ifconfig: ioctl 0x8914 failed: Cannot assign requested address
- ifconfig: ioctl 0x8914 failed: Cannot assign requested address
- /sbin/lan.sh: line 63: hostname: not found
- br0: topology change detected, propagating
- br0: port 2(eth2.1) entering forwarding state
- br0: topology change detected, propagating
- br0: port 1(ra0) entering forwarding state
- killall: udhcpd: no process killed
- Port0 is up. Skip.
- ifconfig: ioctl 0x8913 failed: No such device
- /sbin/lan.sh: line 161: can't create /proc/sys/net/ipv6/conf/all/forwarding: nonexistent directory
- in internet.sh -----------------end
- ###########################################
- ############internet.sh end##############
- ############00:00:30######
- ############internet.sh end##############
- ###########################################
- sh: /bin/super_dmz: not found
- sh: ntp.sh: not found
- sh: ddns.sh: not found
- cat: can't open '/var/run/wscd.pid.ra0': No such file or directory
- kill: you need to specify whom to kill
- webs: Listening for HTTP requests at address 192.168.169.1
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- dir_3ffbfe gpio_18 - 10 10 1 3 4000
- process '/bin/login' (pid 1173) exited. Scheduling for restart.
- starting pid 2130, tty '/dev/ttyS1': '/bin/login'
- (none) login:
复制代码 |
|