求教移动h218n v1.0 如何刷机！！

f1p***

按reset  加电源无法进入 CFE，用TTL 线   ctrl+c 也无法中断  。请各位指点一下，谢谢！


one


CFE version 5.60.120.9  based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Fri Nov 15 13:27:29 CST 2013 (xialei@localhost.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found a 16MB ST compatible serial flash
Serial flash offset 00000000 size 128KB
Serial flash offset 00020000 size 640KB
Serial flash offset 000C0000 size 1KB
Serial flash offset 000C0100 size 10944KB
Serial flash offset 00B70000 size 1et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.120.9
CPU type 0x19749: 500MHz
Tot mem: 65536 KBytes

CFE mem:    0x80700000 - 0x8079A2A0 (631456)
Data:       0x8072F810 - 0x80732D40 (13616)
BSS:        0x80732D40 - 0x807342A0 (5472)
Heap:       0x807342A0 - 0x807982A0 (409600)
Stack:      0x807982A0 - 0x8079A2A0 (8192)
Text:       0x80700000 - 0x8072F80C (194572)

Device eth0:  hwaddr 00-90-4C-01-06-00, ipaddr 192.168.1.254, mask 255.255.255.0
        gateway not set, nameserver not set
*** Press 1 means entering boot mode***
Press 2 means entering testing mode***
01 csp magic err!ering norm mode***
foundVer = 1
****Try the first image...
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: Failed.
Could not load :: Interrupted
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: ..Linux version 2.6.21.5 (xialei@localhost.localdomain) (gcc version 4.2.3) #2 Fri Nov 15 14:06:50 CST 2013
Found chip type AI (0x18925357)
Chipc: rev 38, caps 0x10480109, chipst 0x20d0a pmurev 9, pmucaps 0x28a42a09
No PLL init done for chip 5357 rev 2 pmurev 9
si_kattach done. ccrev = 38, wd_msticks = 32
Found a 16MB ST compatible serial flash
Serial flash device: name SFLASH 16384 kB, id 0x0000 size 16384KB
prom init
Check boot para cksum...
boot para cksum OK!
bootPara.runmode=3
errorepc cea2f7db
hnd_cpu_reset=8011fd40
CPU revision is: 00019749
Total Flash size: 16384K with 256 sectors
Flash split 8 : AuxFS[1376256]
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 96 pages used for memmap
  Normal 200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM5357 rev 2 at 500 MHz
Using 250.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Allocating memory for DSP module core and initialization code
Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0
Memory: 60692k/65536k available (2858k kernel code, 4828k reserved, 753k data, 136k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80500000 ... 0x80600000>
Calibrating delay loop... 497.66 BogoMIPS (lpj=248832)
Mount-cache hash table entries: 512
pdt_cspkernel_init
NET: Registered protocol family 16
1192:57:47 [Klogctl][Info] [(1657)LogCtlInit] LogCtlInit begin
1192:57:47 [Klogctl][Info] [(1396)AddLogtab] AddLogtab: pLogTab=80384510,wLogTabNum=64,dwLogTabIDBase = 0X00000000
1192:57:47 [Klogctl][Info] [(1463)AddLogOutModule] AddLogOutModule:OutputMode=0X00000200,ptLogProcSet=81095c48
1192:57:47 [Klogstdio][Info] [(1080)LogStdioProcInit] LogStdioProcInit

1192:57:47 [Klogctl][Info] [(1463)AddLogOutModule] AddLogOutModule:OutputMode=0X00000100,ptLogProcSet=81095c48
1192:57:47 [Klogfile][Info] [(2924)LogFileProcInit] LogFileProcInit

1192:57:47 [Klogfile][Info] [(2936)LogFileProcInit] g_dwUptime is 946684800

1192:57:47 [Klogctl][Info] [(1396)AddLogtab] AddLogtab: pLogTab=80385d50,wLogTabNum=2,dwLogTabIDBase = 0X00080000
1192:57:47 [Klogctl][Info] [(1512)SetLogOutputMode] SetLogOutputMode:bType=1,OutputMode=0X00000700
1192:57:47 [Klogctl][Info] [(1590)SetLogConf] SetLogConf OutputMode=0X00000100,pBuf=81095aa0,iLen=88
1192:57:47 [Klogfile][Info] [(2743)ProcLogConf] Set LOG_FILE_CONF_SET_PDTCONF

1192:57:47 [Klogfile][Info] [(2831)ProcLogConf] Set LogFileFormatTimestamp
1192:57:47 [Klogctl][Info] [(1723)LogCtlInit] LogCtlInit end
1192:57:47 [KLogCtl][Notice] [oss_logctl.c(321)ProcLog] System start!
1192:57:47 [Klogfile][Info] [(475)InitLogSaveBuff] InitLogSaveBuff
1192:57:47 [KMONITOR][Notice] [monitor.c(199)MonitorInit]  cspmonitor init... !  
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: no core
PCI: Fixing up bus 0
1192:57:47 [MIRROR][Notice] [cspmirror.c(692)MirrorInit]  CspMirror start init ...
1192:57:47 [KQOS][Info] [qos.c(294)CSPKernel_QC_In] Qos module init
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
ip_rt_init() start call CSP_alloc_large_system_hash
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
ip_rt_init() call CSP_alloc_large_system_hash end
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
fwflash_m module registering
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
pflash: found no supported devices
Creating 7 MTD partitions on "sflash":
0x00000000-0x01000000 : "whole flash"
0x00000000-0x00020000 : "boot"
0x00020000-0x000c0000 : "config"
0x000c0000-0x00370000 : "kernel1"
0x00370000-0x00b70000 : "fs1"
0x00d00000-0x00ff0000 : "ctfs"
0x00ff0000-0x01000000 : "nvram"
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
brcmboard: brcm_board_init entry
u32 classifier
    Actions configured
nf_conntrack version 0.5.0 netfilter PSD loaded - (c) astaro AG
NET: Registered protocol family 1
NET: Registered protocol family 10
6WIND/LSIIT IPv6 muNET: Registered protocol family 17
af_packet.c packet_init call register_netdevice_notifier
Bridge firewalling registered
br_init call register_netdevice_notifier
Ebtables v2.0 registered
NET: Registered protocol family 24
PPP Deflate Compression module registered
1192:57:47 [LEDKEYDRV][Info] [ledkey_mod.c(1733)LedkeymodInit] Ledkey_mod Driver Version 0.0.1.
1192:57:47 [LEDKEYDRV][Info] [ledkey_mod.c(1784)LedkeymodInit] watchdog enable!
1192:57:47 [TAGPARAM][Info] [tagparam_mod.c(1383)TagaramodInit] Tagaram module Driver Version 0.0.1.
1192:57:47 [TAGPARAM][Info] [tagparam_mod.c(1423)TagaramodInit] parse tag param success
1192:57:47 [km255][Info] [ver_info.c(349)ver_info_init] ver_info_init
tcVerInfo->bootWhichImg=1
bootPara.img_info_tbl[0].flashOffset=0x   c0000
sHardVersion=V1.12


----------cp0_errorepc == 0xcea2f7db
1192:57:47 [km255][Info] [ver_info.c(138)ReadInfoFromVer] ver_info_init
1192:57:47 [km255][Info] [ver_info.c(145)ReadInfoFromVer] ver_info_init
1192:57:47 [km255][Info] [ver_info.c(161)ReadInfoFromVer] wFirmwareForm is:0x0
1192:57:47 [KSWETH][Notice] [csp_ifinfo.c(191)csp_ifinfo_init] Initializing CSP IFinfo...
1192:57:47 [KSWETH][Warn] [csp_ifinfo.c(213)csp_ifinfo_init] No IFinfo in flash!
1192:57:47 [KSWETH][Notice] [sweth_core.c(3677)sweth_init] SW&ETH HAL driver initing!
1192:57:47 [KSWETH][Notice] [sweth_core.c(152)CreateSwEthObjs] Create SW & ETH objects
1192:57:47 [KSWETH][Notice] [sweth_core.c(168)CreateSwEthObjs] Failed to get SWITCH attr, iRet=-2
1192:57:47 [KSWETH][Info] [sweth_core.c(175)CreateSwEthObjs] nEmac = 1, nSw = 0, nEth=5.
1192:57:47 [KSWETH][Info] [sweth_core.c(334)CreateSwEthObjs] ETH obj0: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 0
1192:57:47 [KSWETH][Info] [sweth_core.c(334)CreateSwEthObjs] ETH obj1: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 1
1192:57:47 [KSWETH][Info] [sweth_core.c(334)CreateSwEthObjs] ETH obj2: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 2
1192:57:47 [KSWETH][Info] [sweth_core.c(334)CreateSwEthObjs] ETH obj3: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 3
1192:57:47 [KSWETH][Info] [sweth_core.c(334)CreateSwEthObjs] ETH obj4: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 4
1192:57:47 [KFASTFORWARD][Info] [ff_api.c(44)cspFastL2HookRe] CSP_FF_L2_DEL_HOOK register ok.
1192:57:47 [KFASTFORWARD][Info] [ff_api.c(50)cspFastL2HookRe] CSP_FF_L2_AGE_HOOK register ok.
1192:57:47 [KFASTFORWARD][Info] [ff_api.c(56)cspFastL2HookRe] CSP_FF_L2_CLR_HOOK register ok.
1192:57:47 [KFASTFORWARD][Info] [ff_api.c(145)cspFastL3HookRe] CSP_FF_L3_DEL_HOOK register ok.
1192:57:47 [KFASTFORWARD][Info] [ff_api.c(151)cspFastL3HookRe] CSP_FF_L3_AGE_HOOK register ok.
1192:57:47 [KFASTFORWARD][Info] [ff_api.c(157)cspFastL3HookRe] CSP_FF_L3_CLR_HOOK register ok.
1192:57:47 [KMCFAST][Info] [mc_fast_api.c(55)cspMCFFDelMacHo] CSP_MCFF_DEL_MAC_HOOK register ok.
1192:57:47 [KMCFAST][Info] [mc_fast_api.c(36)cspMCFFDelVerEn] CSP_MCFF_DEL_VER_ENTRY_HOOK register ok.
1192:57:47 [KMCFAST][Info] [mc_fast_api.c(77)cspMFFDDelHookR] CSP_MFFD_DEL_HOOK register ok.
1192:57:47 [KMCFAST][Info] [mc_fast_api.c(148)cspMFFCDelHookR] CSP_MFFC

BusyBox v1.01 (2013.11.15-05:41+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
# 1192:57:50 [FLASHRW][Info] [proc_file_mod.c(1196)file_open] open file: /proc/cfg/logconf
1192:57:50 [FLASHRW][Info] [proc_file_mod.c(1326)file_close] close file: /proc/cfg/logconf
1192:57:50 [FLASHRW][Info] [proc_file_mod.c(1196)file_open] open file: /pr
#
#

邪恶***

*** Press 1 means entering boot mode***
Press 2 means entering testing mode***

在这里按1或者2试试看...