|
|
本来用的好好的NR256P，突然之间连不上，重启后发现LAN连IP地址都发布出来，就参照网上大神TTL刷机方法，连接好TTL线，在终端里却没找到刷入命令什么的，
贴出TTL信息，希望有高手指点下我该如何操作！感激不尽！
U-Boot 1.1.3 (Feb 26 2013 - 16:18:16)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fac000
Default FLASH_CS0_CFG = 0511FFA1
flash_protect ON: from 0xBF000000 to 0xBF02077B
flash_protect ON: from 0xBF030000 to 0xBF030FFF
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.4.0.0
--------------------------------------------
ASIC 3052_MP2 (Port5<->MII)
DRAM component: 256 Mbits SDR
DRAM bus: 32 bit
Total memory: 64 MBytes
Flash component: NOR Flash
Date:Feb 26 2013 Time:16:18:16
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 384 MHZ ####
SDRAM bus set to 32 bit
SDRAM size =64 Mbytes
welcome!
3: System Boot system code via Flash.
## Booting image at bf1c0000 ...
Image Name: NR256P;;netcore
Created: 2013-07-03 7:11:49 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 5560791 Bytes = 5.3 MB
Load Address: 80000000
Entry Point: 80366000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80366000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.21 (root@localhost.localdomain) (gcc version 3.4.2) #100 Wed Jul 3 15:06:44 CST 2013
The CPU feqenuce set to 384 MHz
CPU revision is: 0001964c
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Built 1 zonelists. Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = d0808050, status = 11000000
PID hash table entries: 256 (order: 8, 1024 bytes)
calculating r4koff... 003a9800(3840000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60536k/65536k available (2942k kernel code, 4944k reserved, 533k data, 140k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
kernel : 0x11ba27
ralink flash device: 0x800000 at 0x1f000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 7 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00800000 : "ALL"
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Config"
0x00040000-0x001c0000 : "Factory"
0x001c0000-0x002dba27 : "Kernel"
mtd: partition "Kernel" doesn't end on an erase block -- force read-only
0x002dba27-0x00800000 : "RootFS"
mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only
0x001c0000-0x00800000 : "Kernel_RootFS"
DLM (built Oct 24 2012 15:30:58) installed
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.6 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
rdm_major = 254
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.0 256 rx/tx descriptors allocated, mtu = 1500!
GDMA1_MAC_ADRH -- : 0x0000000c
GDMA1_MAC_ADRL -- : 0x432880c5
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
physmap platform flash device: 00800000 at bf000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
block2mtd: version $Revision: 1.1.1.1 $
hbwrr_reg:0
u32 classifier
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2048 buckets, 16384 max)
ctnetlink v0.93: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
ipt_time loading
arp_tables: (C) 2002 David S. Miller
mid :0, nr = 4
mid :1, nr = 12
mid :2, nr = 2
mid :3, nr = 10
mid :4, nr = 34
mid :5, nr = 15
mid :6, nr = 25
mid :7, nr = 12
mid :8, nr = 3
net sniffer init ok.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
NETCORE fastpath V0.03
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 140k freed
init started: BusyBox v1.1.2 (2012.10.24-07:53+0000) multi-call binary
Starting pid 12, console /dev/ttyS1: '/etc/rcS'
Algorithmics/MIPS FPU Emulator v1.5
/etc/rcS: /etc/rcS: 2: /var/run: not found
check 0
monut ok!
mkdir: Cannot create directory `/var/parame/brk': File exists
mkdir: Cannot create directory `/var/parame/parame': File exists
phy_tx_ring = 0x03ed9000, tx_ring = 0xa3ed9000
phy_rx_ring = 0x03eda000, rx_ring = 0xa3eda000
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 710000
eth2.5: Setting MAC address to 00 00 00 00 51 82.
device eth2 entered promiscuous mode
VLAN (eth2.5): Setting underlying device (eth2) to promiscious mode.
eth2.1: Setting MAC address to 00 00 00 00 51 83.
eth2.2: Setting MAC address to 00 00 00 00 51 84.
PPTP driver version 0.8.4
klips_info:ipsec_init: KLIPS startup, Openswan KLIPS IPsec stack version: 2.6.38
NET: Registered protocol family 15
registered KLIPS /proc/sys/net<6>klips_info:ipsec_alg_init: KLIPS alg v=0.8.1-0 (EALG_MAX=255, AALG_MAX=255)
klips_info:ipsec_alg_init: calling ipsec_alg_static_init()
ipsec_aes_init(alg_type=15 alg_id=12 name=aes): ret=0
ipsec_aes_init(alg_type=14 alg_id=9 name=aes_mac): ret=0
ipsec_3des_init(alg_type=15 alg_id=3 name=3des): ret=0
KLIPS cryptoapi interface: alg_type=15 alg_id=12 name=cbc(aes) keyminbits=128 keymaxbits=256, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=253 name=cbc(twofish) keyminbits=128 keymaxbits=256, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=252 name=cbc(serpent) keyminbits=128 keymaxbits=256, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=6 name=cbc(cast5) keyminbits=128 keymaxbits=128, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=7 name=cbc(blowfish) keyminbits=96 keymaxbits=448, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=3 name=cbc(des3_ede) keyminbits=192 keymaxbits=192, found(0)
cp: /tmp/log: No such file or directory
Please press Enter to activate this console. [tar_flag : 732] : tar OK !
igd_filter_ddos_enable_set[line=10700] ddos disabled
check this:igd_ip_pool_proc[277]msg 5 doesn't support
check this:igd_ip_pool_proc[277]msg 5 doesn't support
sucessed set index = 1, ns_mode = 0 sub mode = 0
sucessed set index = 2, ns_mode = 0 sub mode = 0
sucessed set index = 3, ns_mode = 0 sub mode = 0
sucessed set index = 4, ns_mode = 0 sub mode = 0
if_set_ispmap_by_if_id:isp = 0, currently ifmap = 0x1.
if_set_ispmap_by_if_id:isp = 0, currently ifmap = 0x3.
if_set_ispmap_by_if_id:isp = 0, currently ifmap = 0x7.
if_set_ispmap_by_if_id:isp = 0, currently ifmap = 0xf.
eth2.5: Setting MAC address to 08 10 77 df a0 47.
ralink switch vlan operate:init
ralink switch vlan operate:port
ralink switch vlan operate:port
ralink switch vlan operate:port
ralink switch vlan operate:entry
ralink switch vlan operate:entry
ralink switch vlan operate:entry
ralink switch vlan operate:init
ralink switch vlan operate:port
ralink switch vlan operate:port
ralink switch vlan operate:port
ralink switch vlan operate:entry
ralink switch vlan operate:entry
ralink switch vlan operate:entry
eth2.5: dev_set_promiscuity(master, 1)
device eth2.5 entered promiscuous mode
ralink_gpio_ioctl:194 pid:152,req:0x00000011,arg:0x00000001
ralink_gpio_ioctl:194 pid:152,req:0x00000008,arg:0x00000001
ralink_gpio_ioctl:194 pid:152,req:0x0000000a,arg:0x7ff9fdb8
|
|
/1 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2015-9-14 18:24
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
