找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 5028|回复: 16

tp-wrd7500 v5.0TTL没法中断,求大神帮忙提取ART

[复制链接]
发表于 2015-12-19 18:57 | 显示全部楼层 |阅读模式
TTL输出如下U-Boot 1.1.4 (Oct 13 2015 - 12:52:11)(COMPRESSED)

ap135 - Scorpion 1.0

DRAM:  128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 210k for U-Boot at: 87fc8000
Reserving 132k for malloc() at: 87fa7000
Reserving 44 Bytes for Board Info at: 87fa6fd4
Reserving 36 Bytes for Global Data at: 87fa6fb0
Reserving 128k for boot params() at: 87f86fb0
Stack Pointer at: 87f86f98
Now running in RAM - U-Boot at: 87fc8000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17
Flash:  8 MB
Using default environment

Autobooting in 1 seconds
verifying uboot partition...
ok
verifying kernel and romfs partition...
ok

U-Boot 1.1.4 (Nov  6 2015 - 11:39:53)

ap135 - Scorpion 1.0

DRAM:  128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 140k for U-Boot at: 87fdc000
Reserving 132k for malloc() at: 87fbb000
Reserving 44 Bytes for Board Info at: 87fbafd4
Reserving 36 Bytes for Global Data at: 87fbafb0
Reserving 128k for boot params() at: 87f9afb0
Stack Pointer at: 87f9af98
Now running in RAM - U-Boot at: 87fdc000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17
Flash:  8 MB
Using default environment


Now booting Linux!

Autobooting in 1 seconds
## Booting image at 9f040000 ...
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 3.3.8 (tplink@tplink-0B) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Fri Nov 6 11:46:37 CST 2015
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019750 (MIPS 74Kc)
[    0.000000] SoC: Qualcomm Atheros QCA9558 rev 0
[    0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00008000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00008000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=AP135 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 126352k/131072k available (2211k kernel code, 4720k reserved, 568k data, 184k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:83
[    0.000000] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 512
[    0.070000] Initialized recycle list for cpu 0.
[    0.070000] NET: Registered protocol family 16
[    0.080000] gpiochip_add: registered GPIOs 0 to 23 on device: ath79
[    0.080000] MIPS: machine is Atheros AP135 reference board
[    0.090000] ar724x-pci ar724x-pci.0: PCIe link is down
[    0.090000] registering PCI controller with io_map_base unset
[    0.100000] registering PCI controller with io_map_base unset
[    0.110000] bio: create slab <bio-0> at 0
[    0.110000] PCI host bridge to bus 0000:00
[    0.120000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[    0.120000] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.130000] PCI host bridge to bus 0000:01
[    0.130000] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[    0.140000] pci_bus 0000:01: root bus resource [io  0x0001]
[    0.140000] pci 0000:01:00.0: invalid calibration data
[    0.150000] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[    0.150000] pci 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[    0.160000] pci 0000:01:00.0: using irq 41 for pin 1
[    0.160000] Switching to clocksource MIPS
[    0.170000] NET: Registered protocol family 2
[    0.170000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.170000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.180000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.180000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.190000] TCP reno registered
[    0.190000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.200000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.200000] NET: Registered protocol family 1
[    0.220000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.220000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.230000] msgmni has been set to 246
[    0.240000] io scheduler noop registered
[    0.240000] io scheduler deadline registered (default)
[    0.250000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.270000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.280000] console [ttyS0] enabled, bootconsole disabled
[    0.280000] console [ttyS0] enabled, bootconsole disabled
[    0.290000] m25p80 spi0.0: found s25fl064k, expected m25p80
[    0.300000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.300000] Searching for RedBoot partition table
[    0.310000] 9 RedBoot partitions found on MTD device spi0.0
[    0.310000] Creating 9 MTD partitions on "spi0.0":
[    0.320000] 0x000000000000-0x00000001d800 : "factory_boot"
[    0.320000] mtd: partition "factory_boot" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.340000] 0x00000001d800-0x00000001e000 : "factory_info"
[    0.340000] 0x00000001e000-0x000000020000 : "art"
[    0.350000] 0x000000020000-0x000000030000 : "config"
[    0.360000] 0x000000030000-0x000000040000 : "boot"
[    0.360000] 0x000000040000-0x00000013fe64 : "kernel"
[    0.370000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.380000] 0x00000013fe64-0x0000006b0000 : "rootfs"
[    0.390000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] mtd: partition "rootfs" set to be root filesystem
[    0.410000] 0x0000006b0000-0x000000800000 : "rootfs_data"
[    0.410000] 0x000000040000-0x000000800000 : "firmware"
[    0.420000] Registered character driver slp_flash_chrdev
[    0.420000] u32 classifier
[    0.430000]     Performance counters on
[    0.430000]     input device check on
[    0.430000]     Actions configured
[    0.440000] nf_conntrack version 0.5.0 (1974 buckets, 7896 max)
[    0.440000] TCP cubic registered
[    0.450000] NET: Registered protocol family 17
[    0.450000] 8021q: 802.1Q VLAN Support v1.8
[    0.460000] Flash UID signiture check OK.
[    0.470000] ### of_selftest(): No testcase data in device tree; not running tests
[    0.480000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[    0.480000] Freeing unused kernel memory: 184k freed
tpltpl- preinit -
[    2.580000] JFFS2 notice: (339) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
switching to jffs2
- init -

Please press Enter to activate this console. Fri Nov  6 03:46:00 UTC 2015
[    5.710000] athrs17_reg_init: complete
[    5.710000] GMAC: cfg1 0x80000000 cfg2 0x7235
[    5.820000] athrs17_reg_init_wan done
[    5.820000] GMAC: cfg1 0x800c0000 cfg2 0x7000
[    6.340000] ag71xx_mdio: probed
[    6.470000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    7.050000] eth0: Atheros AR8327 switch driver attached.
[    8.230000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    8.240000] eth1: Atheros AG71xx at 0xba000000, irq 5
[    9.020000] SCSI subsystem initialized
[    9.150000] usbcore: registered new interface driver usbfs
[    9.150000] usbcore: registered new interface driver hub
[    9.160000] usbcore: registered new device driver usb
[    9.300000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[    9.580000] PPP generic driver version 2.4.2
[    9.670000] asf: module license 'Proprietary' taints kernel.
[    9.680000] Disabling lock debugging due to kernel taint
[    9.990000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)
[   10.010000] ath_rate_atheros loaded
[   10.090000] ath_tx99 loaded
[   10.230000] ath_dev loaded
[   11.650000] 2G Caldata: 02 02 00 02 03 04 05 06 00 00 00 00 00 00 00 00
[   11.680000] ath_pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[   11.680000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[   12.700000] 5G Caldata: 44 08 AE 91 02 0D 00 03 7F 00 00 00 00 00 00 00
[   13.760000] GRE over IPv4 demultiplexor driver
[   13.780000] GRE over IPv4 tunneling driver
[   13.810000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.950000] xt_time: kernel timezone is -0000
[   14.040000] NET: Registered protocol family 24
[   14.180000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   14.190000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller
[   14.200000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[   14.240000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[   14.260000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[   14.260000] hub 1-0:1.0: USB hub found
[   14.270000] hub 1-0:1.0: 1 port detected
[   14.270000] ehci-platform ehci-platform.1: Generic Platform EHCI Controller
[   14.280000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[   14.320000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[   14.340000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[   14.340000] hub 2-0:1.0: USB hub found
[   14.350000] hub 2-0:1.0: 1 port detected
[   14.610000] PPTP driver version 0.8.5
[   15.200000] nf_conntrack_rtsp v0.6.21 loading
[   15.220000] nf_nat_rtsp v0.6.21 loading
[   15.310000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   15.390000] uhci_hcd: USB Universal Host Controller Interface driver
[   15.490000] Initializing USB Mass Storage driver...
[   15.500000] usbcore: registered new interface driver usb-storage
[   15.510000] USB Mass Storage support registered.
[   15.580000] Registered character driver slp_gpio_chrdev
[   15.810000] fuse init (API version 7.18)
uci: Entry not found (protocol.wan.macaddr)
[CFG_MAC]user did not configured wan mac, use default.
wifi-freq
[   18.250000] ar8327: Disable igmp snooping function.
Command failed: Not found
USB port event happened -- port=1
USB port event happened -- port=2
[   19.000000] eth1: link up (1000Mbps/Full duplex)
[   19.010000] device eth1 entered promiscuous mode
[   19.010000] br-lan: port 1(eth1) entered listening state
[   19.020000] br-lan: port 1(eth1) entered listening state
[   21.020000] br-lan: port 1(eth1) entered learning state
[   23.020000] br-lan: topology change detected, propagating
[   23.020000] br-lan: port 1(eth1) entered forwarding state
[   27.630000] 8021q: adding VLAN 0 to HW filter on device ath0
[   27.630000] device ath0 entered promiscuous mode
[   27.650000] br-lan: port 2(ath0) entered listening state
[   27.650000] br-lan: port 2(ath0) entered listening state
[   27.720000] device ath2 entered promiscuous mode
[   27.730000] device wdscli0 entered promiscuous mode
[   29.650000] br-lan: port 2(ath0) entered learning state
[   29.900000] 8021q: adding VLAN 0 to HW filter on device ath1
[   29.900000] device ath1 entered promiscuous mode
[   29.910000] br-lan: port 5(ath1) entered listening state
[   29.910000] br-lan: port 5(ath1) entered listening state
[   29.980000] device ath3 entered promiscuous mode
[   29.990000] device wdscli1 entered promiscuous mode
[   30.560000] [stat]Lan ip: C0A80101, Lan mask: FFFFFF00
[   30.560000] [stat]wan dev name: eth0
[   30.790000] ----IGMP init begin------
[   30.790000] wan_dev_index = 255 lan_dev_name=br-lan wan_dev_name=eth0
[   30.800000] ----IGMP has been loaded------
wlan has already started in etc/init.d/network script.
[   31.650000] br-lan: topology change detected, propagating
[   31.650000] br-lan: port 2(ath0) entered forwarding state
[   31.910000] br-lan: port 5(ath1) entered learning state
[   32.600000] ol_vdev_start_resp_ev for vap 0 (86740000)
[   32.610000] ol_ath_vap_join: join operation is only for STA/IBSS mode
[   32.620000] ol_ath_wmm_update:
[   32.620000] Notification to UMAC VAP layer
Loading redirects
Loading dmz
Loading forbidhost
Loading localmanage
Loading hostctrl
[   33.910000] br-lan: topology change detected, propagating
[   33.910000] br-lan: port 5(ath1) entered forwarding state
Loading includes
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such file or directory
uci: Entry not found (guest_network.@guest_rule_2g[0])
uci: Entry not found (guest_network.@guest_rule_5g[0])
uci: Entry not found (guest_network.@guest_rule_2g[0])
uci: Entry not found (guest_network.@guest_rule_5g[0])
[   38.410000] SFE IPv4 init
[   38.490000] SFE Fast-Classifier init
[   39.170000] kcg 333 :GPL NetUSB up!
[   39.280000] kc   90 : run_telnetDBGDServer start
[   39.290000] kc  227 : init_DebugD end
[   39.290000] INFO186B: NetUSB 1.02.62, 00030308 : Jan 15 2015 14:28:35
[   39.300000] INFO186D: 7437: TL-WDR7500 :TL-WDR7500
[   39.300000] INFO186E:  AUTH ISOC
[   39.300000] INFO186F:  MOVE_HEAD filterAudio
[   39.310000] usbcore: registered new interface driver KC NetUSB General Driver
[   39.320000] INFO18C7: Reset device when disconnect
[   39.320000] INFO0145:  init proc : PAGE_SIZE 4096
[   39.330000] INFO1740:  infomap 85086d1c
[   39.330000] INFO1743:  sleep to wait br-lan to wake up
[   39.340000] INFO02CE:  use dev Name br-lan
[   39.340000] INFO174C:  sleep to wait br-lan end.
[   39.340000] INFO1765:  UDP_BROAD 7437 tcpPort:625868800
[   39.350000] INFO02CE:  use dev Name br-lan
[   39.380000] INFO161F: tcpConnector() started...
[   42.440000] INFO14F8: Bind to br-lan
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
 楼主| 发表于 2015-12-19 19:01 | 显示全部楼层
http://pan.baidu.com/s/1bbDoku 编辑器固件 自己提取的ART是64K但是怎么不对,刷OP和DD都没无线 求大神帮忙提取一下
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2015-12-19 20:19 来自手机 | 显示全部楼层
求大神帮帮忙啊
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2015-12-19 20:58 来自手机 | 显示全部楼层
自己顶
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

发表于 2015-12-20 10:13 | 显示全部楼层
ART位于0x1e000-0x20000

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

点评

谢谢啊 刷你的op无线驱动成功,2G 5G都有信号,换16M FLASH成功,以后随便刷了谢谢  详情 回复 发表于 2015-12-20 19:08
跪求大神帮忙提取个BERRD能刷的ART啊 谢谢 8K的能刷吗  详情 回复 发表于 2015-12-20 14:35
8k的ART怎么刷啊 小白不懂啊 981213大大  详情 回复 发表于 2015-12-20 14:33
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2015-12-20 14:33 | 显示全部楼层
981213 发表于 2015-12-20 10:13
ART位于0x1e000-0x20000

8k的ART怎么刷啊 小白不懂啊 981213大大
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2015-12-20 14:35 | 显示全部楼层
981213 发表于 2015-12-20 10:13
ART位于0x1e000-0x20000

跪求大神帮忙提取个BERRD能刷的ART啊 谢谢 8K的能刷吗

点评

再次跪求大神帮忙一下 64K的ART谢谢 小白真不会,网上没教程,完全自学  详情 回复 发表于 2015-12-20 15:26
不会填充啊 不知道怎么弄  详情 回复 发表于 2015-12-20 15:23
填充到64k不就是了……………………  发表于 2015-12-20 15:12
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2015-12-20 15:23 | 显示全部楼层
love3dspsp 发表于 2015-12-20 14:35
跪求大神帮忙提取个BERRD能刷的ART啊 谢谢 8K的能刷吗

不会填充啊 不知道怎么弄
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2015-12-20 15:26 | 显示全部楼层
love3dspsp 发表于 2015-12-20 14:35
跪求大神帮忙提取个BERRD能刷的ART啊 谢谢 8K的能刷吗

再次跪求大神帮忙一下 64K的ART谢谢 小白真不会,网上没教程,完全自学
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2015-12-20 16:26 | 显示全部楼层
如何填充ART啊 求指点
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

发表于 2015-12-20 17:29 | 显示全部楼层
仔细想了想不能直接填充……

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

点评

太感谢了 好人一身平安  详情 回复 发表于 2015-12-20 18:14
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2015-12-20 18:14 | 显示全部楼层
981213 发表于 2015-12-20 17:29
仔细想了想不能直接填充……

太感谢了 好人一身平安
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2015-12-20 19:08 | 显示全部楼层
981213 发表于 2015-12-20 10:13
ART位于0x1e000-0x20000

谢谢啊 刷你的op无线驱动成功,2G 5G都有信号,换16M FLASH成功,以后随便刷了谢谢
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

发表于 2016-1-3 23:27 | 显示全部楼层
也是和其他型号一样放在最后64k么?
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

欢迎大家光临恩山无线论坛上一条 /1 下一条

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-10-5 04:31

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com

快速回复 返回顶部 返回列表