设为首页收藏本站

简体中文 繁體中文 English 日本語 Deutsch 한국 사람 بالعربية TÜRKÇE português คนไทย

🌓 切换到窄版

 找回密码
 立即注册

QQ登录

只需一步，快速开始

搜索
恩山无线论坛»论坛 › 无线设备软件相关板块 › OPENWRT专版 › 请问MW150R改了USB的大大，是否加装USB刷了WRT后都这么 ...
广告投放联系QQ68610888
返回列表 发新帖
查看: 5724|回复: 8

请问MW150R改了USB的大大，是否加装USB刷了WRT后都这么热

[复制链接]
发表于 2011-11-9 01:15 | 显示全部楼层 |阅读模式
本帖最后由 animefans_xj 于 2011-11-10 15:32 编辑

刚买回来的时候外壳是凉的，底下的外壳温的
感觉刷了WRT，加了USB后好热。外壳是温热的，底下的外壳更热，但还不烫手。拆开外壳摸主控，非常烫,手都不能长时间接触，主板反面的散热覆铜的颜色都有点变深了，但是检查了半天都没发现短路什么的。机器工作虽然不稳定，但也还算正常。难道cpu挂了？

OK,不用问了，刚刚eth0开始不停down .. up .. down .. up了，网页都很难加载了，估计是CPU不行了。等挂了火烧法伺候

至于上次说的USB速度只有1M的问题其实USB速度是稳定在9M以上了，不过其实是由于eth1不停Link down .. Link up的，最后速度变成10Mbps了,不过那个时候Link down和Link up没有今天这么频繁，Link up的速度也很快，所以造成了网络没问题的假象


........接口又稳定了，这回变USB不稳定了
mw150us mac, mw150r wds, mw150us怎么用

相关帖子

只谈技术、莫论政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流，建议保持一颗平常心看待网友的评论，切勿过度反应。
回复

使用道具 举报

发表于 2011-11-10 11:06 | 显示全部楼层
未必是硬件问题，有些固件有毛病，会导致eth1不停地link up 、down
只谈技术、莫论政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流，建议保持一颗平常心看待网友的评论，切勿过度反应。
回复 支持 反对

使用道具 举报

q741451
发表于 2011-11-10 12:16 | 显示全部楼层
LZ的头像好萌
只谈技术、莫论政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流，建议保持一颗平常心看待网友的评论，切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2011-11-10 15:35 | 显示全部楼层
本帖最后由 animefans_xj 于 2011-11-10 15:41 编辑

不连接U盘的话貌似网络连接倒是没问题的说

贴上启动信息

  2. Linux version 2.6.39.4 (dyq@dyq-desktop) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Thu Sep 22 19:51:35 CST 2011
  3. prom: fw_arg0=00000007, fw_arg1=a1f8ffb0, fw_arg2=a1f90460, fw_arg3=00000004
  4. MyLoader: sysp=00d73bc7, boardp=ed0c292e, parts=97cba183
  5. bootconsole [early0] enabled
  6. CPU revision is: 00019374 (MIPS 24Kc)
  7. SoC: Atheros AR9330 rev 1
  8. Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
  9. Determined physical RAM map:
  10. memory: 02000000 @ 00000000 (usable)
  11. Initrd not found or empty - disabling initrd
  12. Zone PFN ranges:
  13.   Normal   0x00000000 -> 0x00002000
  14. Movable zone start PFN for each node
  15. early_node_map[1] active PFN ranges
  16.     0: 0x00000000 -> 0x00002000
  17. On node 0 totalpages: 8192
  18. free_area_init_node: node 0, pgdat 802b6820, node_mem_map 81000000
  19.   Normal zone: 64 pages used for memmap
  20.   Normal zone: 0 pages reserved
  21.   Normal zone: 8128 pages, LIFO batch:0
  22. pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
  23. pcpu-alloc: [0] 0
  24. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
  25. Kernel command line:  board=TL-WR740N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
  26. PID hash table entries: 128 (order: -3, 512 bytes)
  27. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  28. Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  29. Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  30. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  31. Writing ErrCtl register=00000000
  32. Readback ErrCtl register=00000000
  33. Memory: 29376k/32768k available (2009k kernel code, 3392k reserved, 386k data, 180k init, 0k highmem)
  34. SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  35. NR_IRQS:80
  36. Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
  37. pid_max: default: 32768 minimum: 301
  38. Mount-cache hash table entries: 512
  39. NET: Registered protocol family 16
  40. MIPS: machine is TP-LINK TL-WR740N v5 by dyq
  41. bio: create slab <bio-0> at 0
  42. Switching to clocksource MIPS
  43. NET: Registered protocol family 2
  44. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  45. TCP established hash table entries: 1024 (order: 1, 8192 bytes)
  46. TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  47. TCP: Hash tables configured (established 1024 bind 1024)
  48. TCP reno registered
  49. UDP hash table entries: 256 (order: 0, 4096 bytes)
  50. UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  51. NET: Registered protocol family 1
  52. PCI: CLS 0 bytes, default 32
  53. squashfs: version 4.0 (2009/01/31) Phillip Lougher
  54. JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  55. msgmni has been set to 57
  56. io scheduler noop registered
  57. io scheduler deadline registered (default)
  58. Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  59. ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
  60. console [ttyATH0] enabled, bootconsole disabled
  61. Atheros AR71xx SPI Controller driver version 0.2.4
  62. m25p80 spi0.0: found mx25l3205d, expected m25p80
  63. m25p80 spi0.0: mx25l3205d (4096 Kbytes)
  64. spi0.0: searching for MyLoader partition table at offset 0x10000
  65. spi0.0: searching for MyLoader partition table at offset 0x20000
  66. spi0.0: searching for MyLoader partition table at offset 0x30000
  67. spi0.0: searching for MyLoader partition table at offset 0x40000
  68. spi0.0: no MyLoader partition table found
  69. Searching for RedBoot partition table in spi0.0 at offset 0x3e0000
  70. Searching for RedBoot partition table in spi0.0 at offset 0x3f0000
  71. No RedBoot partition table detected in spi0.0
  72. spi0.0: no WRT160NL signature found
  73. Creating 6 MTD partitions on "spi0.0":
  74. 0x000000000000-0x000000020000 : "u-boot"
  75. 0x000000020000-0x000000120000 : "kernel"
  76. 0x000000120000-0x0000003f0000 : "rootfs"
  77. mtd: partition "rootfs" set to be root filesystem
  78. mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=110000
  79. 0x0000002e0000-0x0000003f0000 : "rootfs_data"
  80. 0x0000003f0000-0x000000400000 : "art"
  81. 0x000000020000-0x0000003f0000 : "firmware"
  82. 0x000000000000-0x000000400000 : "fullflash"
  83. ag71xx_mdio: probed
  84. eth0: Atheros AG71xx at 0xba000000, irq 5
  85. eth0: Found an AR7240 built-in switch
  86. eth1: Atheros AG71xx at 0xb9000000, irq 4
  87. eth1: connected to PHY at ag71xx-mdio:04 [uid=004dd041, driver=Generic PHY]
  88. Atheros AR71xx hardware watchdog driver version 0.1.0
  89. ar71xx-wdt: timeout=15 secs (max=171)
  90. TCP westwood registered
  91. NET: Registered protocol family 17
  92. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  93. All bugs added by David S. Miller <davem@redhat.com>
  94. VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  95. Freeing unused kernel memory: 180k freed
  96. input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
  97. Button Hotplug driver version 0.4.1
  98. Registered led device: tl-wr740n:green:system
  99. Registered led device: tl-wr740n:green:qss
  100. Registered led device: tl-wr740n:green:wlan
  101. JFFS2 notice: (383) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 21 of xref (0 dead, 2 orphan) found.
  102. eth0: link up (1000Mbps/Full duplex)
  103. SCSI subsystem initialized
  104. usbcore: registered new interface driver usbfs
  105. usbcore: registered new interface driver hub
  106. usbcore: registered new device driver usb
  107. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  108. ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
  109. ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
  110. ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
  111. ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
  112. hub 1-0:1.0: USB hub found
  113. hub 1-0:1.0: 1 port detected
  114. ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  115. uhci_hcd: USB Universal Host Controller Interface driver
  116. eth0: link down
  117. Initializing USB Mass Storage driver...
  118. usbcore: registered new interface driver usb-storage
  119. USB Mass Storage support registered.
  120. usb 1-1: new high speed USB device number 2 using ar71xx-ehci
  121. scsi0 : usb-storage 1-1:1.0
  122. usb 1-1: reset high speed USB device number 2 using ar71xx-ehci
  123. scsi 0:0:0:0: Direct-Access     NowVideo Stack            PMAP PQ: 0 ANSI: 0 CCS
  124. eth0: link up (1000Mbps/Full duplex)
  125. usb 1-1: reset high speed USB device number 2 using ar71xx-ehci
  126. usb 1-1: device descriptor read/64, error -71
  127. usb 1-1: device descriptor read/64, error -71
  128. usb 1-1: reset high speed USB device number 2 using ar71xx-ehci
  129. sd 0:0:0:0: [sda] 3919872 512-byte logical blocks: (2.00 GB/1.86 GiB)
  130. sd 0:0:0:0: [sda] Write Protect is off
  131. sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
  132. sd 0:0:0:0: [sda] Assuming drive cache: write through
  133. sd 0:0:0:0: [sda] Assuming drive cache: write through
  134. usb 1-1: reset high speed USB device number 2 using ar71xx-ehci
  135. sda: sda1 sda2
  136. sd 0:0:0:0: [sda] Assuming drive cache: write through
  137. sd 0:0:0:0: [sda] Attached SCSI removable disk
  138. EXT4-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended
  139. EXT4-fs (sda1): recovery complete
  140. EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
复制代码
只谈技术、莫论政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流，建议保持一颗平常心看待网友的评论，切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2011-11-10 15:36 | 显示全部楼层
  1. eth0: link down
  2. eth0: link up (1000Mbps/Full duplex)
  3. device eth0 entered promiscuous mode
  4. br-lan: port 1(eth0) entering forwarding state
  5. br-lan: port 1(eth0) entering forwarding state
  6. Compat-wireless backport release: compat-wireless-2011-08-25
  7. Backport based on wireless-testing.git master-2011-09-14
  8. cfg80211: Calling CRDA to update world regulatory domain
  9. cfg80211: World regulatory domain updated:
  10. cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  11. cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  12. cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  13. cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  14. cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  15. cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  16. ath: EEPROM regdomain: 0x0
  17. ath: EEPROM indicates default country code should be used
  18. ath: doing EEPROM country->regdmn map search
  19. ath: country maps to regdmn code: 0x3a
  20. ath: Country alpha2 being used: US
  21. ath: Regpair used: 0x3a
  22. ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
  23. Registered led device: ath9k-phy0
  24. ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
  25. cfg80211: Calling CRDA for country: US
  26. eth1: link up (100Mbps/Full duplex)
  27. PPP generic driver version 2.4.2
  28. ip_tables: (C) 2000-2006 Netfilter Core Team
  29. cfg80211: Regulatory domain changed to country: US
  30. cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  31. cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
  32. cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
  33. cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  34. cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  35. cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  36. cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
  37. NET: Registered protocol family 24
  38. nf_conntrack version 0.5.0 (461 buckets, 1844 max)
  39. nf_nat_ftp: Unknown symbol nf_nat_ftp_hook (err 0)
  40. usbcore: registered new interface driver ums-alauda
  41. usbcore: registered new interface driver ums-cypress
  42. usbcore: registered new interface driver ums-datafab
  43. usbcore: registered new interface driver ums-freecom
  44. usbcore: registered new interface driver ums-isd200
  45. usbcore: registered new interface driver ums-jumpshot
  46. usbcore: registered new interface driver ums-karma
  47. usbcore: registered new interface driver ums-sddr09
  48. usbcore: registered new interface driver ums-sddr55
  49. usbcore: registered new interface driver ums-usbat
  50. usb 1-1: reset high speed USB device number 2 using ar71xx-ehci
  51. EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
  52. cfg80211: Calling CRDA for country: CN
  53. cfg80211: Regulatory domain changed to country: CN
  54. cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  55. cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
  56. cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)
  57. device wlan0 entered promiscuous mode
  58. br-lan: port 2(wlan0) entering forwarding state
  59. br-lan: port 2(wlan0) entering forwarding state
  60. eth1: link down
  61. eth1: link up (100Mbps/Full duplex)
  62. device wlan0 left promiscuous mode
  63. br-lan: port 2(wlan0) entering forwarding state
  64. device wlan0 entered promiscuous mode
  65. br-lan: port 2(wlan0) entering forwarding state
  66. br-lan: port 2(wlan0) entering forwarding state
  67. ar71xx-wdt: enabling watchdog timer
  68. ar71xx-wdt: timeout=60 secs
复制代码
只谈技术、莫论政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流，建议保持一颗平常心看待网友的评论，切勿过度反应。
回复 支持 反对

使用道具 举报

发表于 2011-11-10 21:15 | 显示全部楼层
1# animefans_xj


别超频了，换回去！
只谈技术、莫论政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流，建议保持一颗平常心看待网友的评论，切勿过度反应。
回复 支持 反对

使用道具 举报

sutuo
发表于 2011-11-10 21:50 | 显示全部楼层
放改USB详图
放uboot
放固件
只谈技术、莫论政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流，建议保持一颗平常心看待网友的评论，切勿过度反应。
回复 支持 反对

使用道具 举报

xll
发表于 2011-11-11 04:00 | 显示全部楼层
usb直接移植的ar71xx的，肯定不稳定，还是等官网驱动吧
只谈技术、莫论政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流，建议保持一颗平常心看待网友的评论，切勿过度反应。
回复 支持 反对

使用道具 举报

q741451
发表于 2011-11-13 21:16 | 显示全部楼层
《月夜的奶酪》，LZ的头像好萌
只谈技术、莫论政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流，建议保持一颗平常心看待网友的评论，切勿过度反应。
回复 支持 反对

使用道具 举报

返回列表 发新帖
高级模式
B Color Image Link Quote Code Smilies
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

欢迎大家光临恩山无线论坛上一条 /1 下一条

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-9-28 15:39

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱：js12377 | @jischina.com.cn 举报电话：025-88802724 本站不良内容举报信箱：68610888@qq.com

快速回复 返回顶部 返回列表