求救:WHR-G300N V2刷死了...

jfm034

刚买回来就刷了DD的..但后来感觉不太稳定..经验掉线(但无线的不会.)..所以在Web下更新了原厂的固件..之后就不能用了..现象为:电源灯跟DIAG灯长亮..

附上TTL输出信息..:
BUFFALO U-BOOT Ver 1.00
AP93 (ar7240) U-boot

sri
================================================================================
=====================================================
  TAP CALC (read_cnt=512)
----+---------------------------------------------------------------------------
-----------------------------------------------------
TAP |   0   1   2   3   4   5   6   7   8   9  10  11  12  13  14  15  16  17  1
8  19  20  21  22  23  24  25  26  27  28  29  30  31
----+---------------------------------------------------------------------------
-----------------------------------------------------
FAIL|                               0   0   0   0   0   0   0   0   0 498 512 51
5122 512 512 512 512 512 512 512 512 512 512 512 512
----+---------------------------------------------------------------------------
-----------------------------------------------------
SELECT tap0=8 / tap1=8

#### ddr registers
  B8000000 = C7BC8CD0
  B8000004 = 9DD0E6A8
  B8000008 = 00000033
  B800000C = 00000002
  B8000010 = 00000000
  B8000014 = 00004AF0
  B8000018 = 000000FF
  B800001C = 00000008
  B8000020 = 00000008
  B8000024 = 00000005
  B8000028 = 00000005


32 MB
Memory Test (address line)
Memory Test start(0xA0000000) end(0xA2000000) size(33554432)
Data line test start:0xa0000000 pattern 0x00000001 0x00000003 0x00000007 0x00000
00F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
Address line test start:0xa0000000 len:0x2000000 pattern 0xAAAAAAAA 0x55555555

Fill test patnum:5
fill Pattern 5555AAAA  Writing...   Reading...
fill Pattern AAAA5555  Writing...   Reading...
fill Pattern 0000FFFF  Writing...   Reading...
fill Pattern FFFF0000  Writing...   Reading...
fill Pattern AAAAAAAA  Writing...   Reading...
Top of RAM usable for U-Boot at: 82000000
Reserving 291k for U-Boot at: 81fb4000
Reserving 136k for malloc() at: 81f92000
Reserving 44 Bytes for Board Info at: 81f91fd4
Reserving 36 Bytes for Global Data at: 81f91fb0
Reserving 128k for boot params() at: 81f71fb0
Stack Pointer at: 81f71f98
Now running in RAM - U-Boot at: 81fb4000
id read 0x100000ff
flash size 4194304, sector count = 1024
Flash:  4 MB
In:    serial
Out:   serial
Err:   serial
Memory Test
uboot use  81F71FB0 - 82000000
Memory Test start(80000000) end(81F00000) size(01F00000)
Pattern 00000000  Writing...  Reading...
Memory Test OK
### buf_ver=[1.00] U-Boot Ver.=[1.00]
### build_date(env)=[Jul 27 2009 - 17:39:39] build_date(bin)=[Jul 27 2009 - 17:3
9:39]
TEST----ag7240_enet_initialize...
TEST----dev[0]->name=eth0-----
TEST----dev[0]->enetaddr=-----
TEST----dev[0]->iobase=0-----
TEST----dev[0]->state=0-----
Reading MAC Address from ENV(0x81f922d9)
eth_register
TEST----dev->state=0----
miiphy_register: added 'eth0', read=0x81fd0f08, write=0x81fd1060
ag7240_hw_start
TEST----mac->mac_unit=0----
TEST----AG7240_MAC_CFG2_else= 0x7337----
TEST---- mac->base=0x19000000----
TEST---- register3c=0x0----
: cfg1 0xf cfg2 0x7337
ag7240_setup_fifos
eth0: 02:aa:bb:cc:dd:1e
eth0 up
TEST----dev[1]->name=eth1-----
TEST----dev[1]->enetaddr=-----
TEST----dev[1]->iobase=0-----
TEST----dev[1]->state=0-----
No valid address in Flash. Using fixed address
eth_register
TEST----dev->state=0----
miiphy_register: added 'eth1', read=0x81fd0f08, write=0x81fd1060
ag7240_hw_start
TEST----mac->mac_unit=1----
TEST----AG7240_MAC_CFG2_else= 0x7337----
TEST---- mac->base=0x1a000000----
TEST---- register3c=0x0----
: cfg1 0xf cfg2 0x7337
ag7240_setup_fifos
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0  02:AA:BB:CCD:1E
, eth1  00:03:7F:09:0B:AD

TEST-----ag7240_check_link----
TEST----duplex=1   1:full 0:half
TEST----athrs26_phy_speed----
TEST----phyHwStatus=31774----
TEST----phyHwStatus=49152----
TEST----phyHwStatus=1----
TEST----speed=100-----
TEST----dup 1 speed 100
TEST----3C=0
TEST----04=7337

tftp server(receive) go, waiting:4[sec]
TEST-----ag7240_check_link----
TEST----duplex=1   1:full 0:half
TEST----athrs26_phy_speed----
TEST----phyHwStatus=31774----
TEST----phyHwStatus=49152----
TEST----phyHwStatus=1----
TEST----speed=100-----
Load address: 0x80f00000

TftpServer Timeout;
no file was loaded.
## Booting image at bf040000 ...
   Image Name:   Linux Kernel Image
   Created:      2009-10-08   2:15:03 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    895439 Bytes = 874.5 kB
   Load Address: 80000000
   Entry Point:  8029b000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8029b000) ...
## Giving linux memsize in bytes, 33554432

Starting kernel ...

看过很多的贴子..但都没成功过....因为在终端机下按Ctrl+C都没反应的..
从TTL输出的信息看..好像也没有啥按键提示的...

请高人提点下....在些先谢谢了!!....QQ:153347899

jfm034

用了好几个TFTP软件.搭建FTP服务器也不成功....没任何连接反应(FTP信息里..)..

daiqipeng

jtag 修复一下就行了，我的搞好了。
现在刷的是dd-wrt

jfm034

daiqipeng 发表于 2012-2-26 21:11
jtag 修复一下就行了，我的搞好了。
现在刷的是dd-wrt

请问兄弟..该怎么操作...??
或能否提供参考资料...

谢谢了.,.

bingtiefeng

我没买G300NH2但看了说明书，直接在web界面上可以刷DD，而且提供了DD的版本，应该是零风险的啊。

江天一色

我刷的DD，挺稳定的啊！刷回原厂固件不是从WEB下更新的。方法参见：http://www.anywlan.com/forum.php ... ra=page%3D1&page=1&

你现在这情况只能表示同情~我是菜鸟，帮不上忙，纯支持！！