|
|
小米3路由器由x-wrt通过后台手动刷OPen-wrt无限重启不知道还有救吗？PUTT一直如此循环，每网卡灯全闪一下跪谢！
!!! nand page size = 2048, addr len=4
..============================================
Ralink UBoot Version: 4.2.S.1
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM_CONF_FROM: Auto-detection
DRAM_TYPE: DDR2
DRAM component: 1024 Mbits
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: NAND Flash
Date:Apr 15 2016 Time:17:46:32
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =128 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
3: System Boot system code via Flash.
Booting System 2
..ranand_erase_write: offs:40000, count:20000
.Done!
done
## Booting image at bc600000 ...
Image Name: MIPS OpenWrt Linux-5.15.148
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2479878 Bytes = 2.4 MB
Load Address: 80000000
Entry Point: 80000000
...................................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
commandline uart_en=0 factory_mode=0 mem=128m
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 5.15.148 (runner@fv-az1152-766) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23753-79a7195087) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 Tue Feb 20 20:58:15 2024
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Xiaomi Mi Router R3
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00019e60
[ 0.000000] Readback ErrCtl register=00019e60
[ 0.000000] mem auto-init: stack ff, heap allocff, heap freeff
[ 0.000000] Memory: 120340K/131072K available (6033K kernel code, 613K rwdata, 1284K rodata, 1212K init, 225K bss, 10732K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000002] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.007813] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.073750] pid_max: default: 32768 minimum: 301
[ 0.079342] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.086404] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.097921] Performance counters: mips/24K PMU enabled, 2 32-bit counters available to each CPU, irq 17
[ 0.113850] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.123439] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.130235] pinctrl core: initialized pinctrl subsystem
[ 0.137130] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.420924] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.426424] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.432935] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.438391] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.446601] PCI host bridge to bus 0000:00
[ 0.450611] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[ 0.457239] pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff]
[ 0.463925] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.471667] pci 0000:00:00.0: [1814:0801] type 01 class 0x060400
[ 0.477471] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 0.483534] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 0.489717] pci 0000:00:00.0: supports D1
[ 0.493547] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.501450] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.509493] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[ 0.515367] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 0.521954] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.528552] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.536642] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.543069] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.549476] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 0.555877] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 0.562632] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 0.569234] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[ 0.576239] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[ 0.582851] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[ 0.589952] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[ 0.596960] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.601768] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 0.608367] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
[ 0.616111] clocksource: Switched to clocksource systick
[ 0.623157] NET: Registered PF_INET protocol family
[ 0.628244] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.636527] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.644736] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.652294] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.659706] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.666556] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.672911] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.679290] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.686578] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.692134] PCI: CLS 0 bytes, default 32
[ 0.696235] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.708953] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.722843] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.728540] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.739977] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.750748] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.760597] printk: console [ttyS0] disabled
[ 0.764798] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.774504] printk: console [ttyS0] enabled
[ 0.774504] printk: console [ttyS0] enabled
[ 0.782961] printk: bootconsole [early0] disabled
[ 0.782961] printk: bootconsole [early0] disabled
[ 0.833021] gsw: setting port4 to ephy mode
[ 0.837538] mtk_soc_eth 10100000.ethernet: generated random MAC address 0a:19:73:2e:25:49
[ 0.845910] mtk_soc_eth 10100000.ethernet: mdio-bus disabled
[ 0.851976] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.858954] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 0.868296] rt2880_wdt 10000120.watchdog: Initialized
[ 0.875490] NET: Registered PF_INET6 protocol family
[ 0.889205] Segment Routing with IPv6
[ 0.893068] In-situ OAM (IOAM) with IPv6
[ 0.897334] NET: Registered PF_PACKET protocol family
[ 0.902600] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.916274] 8021q: 802.1Q VLAN Support v1.8
[ 0.925482] /dev/root: Can't open blockdev
[ 0.929783] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 0.937450] Please append a correct "root=" boot option; here are the available partitions:
[ 0.945981] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 0.954418] Rebooting in 1 seconds..
U-Boot 1.1.3 (Apr 15 2016 - 17:46:32)
Board: Ralink APSoC DRAM: 128 MB
Power on memory test. Memory size= 128 MB...OK!
relocate_code Pointer at: 87fb8000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
请不要胡乱输入以及粘贴、复制等方式灌水
请尊重作者、并共同维护网站的正常阅读，否则账户将会被限制发帖、回帖，并且积分可能会被清零，站内短信以及阅读权限等都会受到影响，谢谢。
具体限制方式：https://www.right.com.cn/forum/thread-8307840-1-1.html
|
|
/1 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2024-3-19 14:35
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
