8L已有报告,20L有拆机图,已更新VDISK链接.关于TP-WR720N我知道的不多...

可忙BB

硬件信息如下：

1. /root$ dmesg
   
2. [    0.000000] Linux version 3.2.13 (dell@dell-Inspiron-1320) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Thu Apr 5 13:59:57 CST 2012
   
3. [    0.000000] MyLoader: sysp=3dd7cb87, boardp=f0717c55, parts=4852ecbe
   
4. [    0.000000] bootconsole [early0] enabled
   
5. [    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
   
6. [    0.000000] SoC: Atheros AR9330 rev 1
   
7. [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
   
8. [    0.000000] Determined physical RAM map:
   
9. [    0.000000]  memory: 02000000 @ 00000000 (usable)
   
10. [    0.000000] Initrd not found or empty - disabling initrd
    
11. [    0.000000] Zone PFN ranges:
    
12. [    0.000000]   Normal   0x00000000 -> 0x00002000
    
13. [    0.000000] Movable zone start PFN for each node
    
14. [    0.000000] early_node_map[1] active PFN ranges
    
15. [    0.000000]     0: 0x00000000 -> 0x00002000
    
16. [    0.000000] On node 0 totalpages: 8192
    
17. [    0.000000] free_area_init_node: node 0, pgdat 802cef90, node_mem_map 81000000
    
18. [    0.000000]   Normal zone: 64 pages used for memmap
    
19. [    0.000000]   Normal zone: 0 pages reserved
    
20. [    0.000000]   Normal zone: 8128 pages, LIFO batch:0
    
21. [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
    
22. [    0.000000] pcpu-alloc: [0] 0
    
23. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
    
24. [    0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
    
25. [    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
    
26. [    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
    
27. [    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
    
28. [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    
29. [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
    
30. [    0.000000] Writing ErrCtl register=00000000
    
31. [    0.000000] Readback ErrCtl register=00000000
    
32. [    0.000000] Memory: 29272k/32768k available (2099k kernel code, 3496k reserved, 393k data, 192k init, 0k highmem)
    
33. [    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    
34. [    0.000000] NR_IRQS:48
    
35. [    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
    
36. [    0.080000] pid_max: default: 32768 minimum: 301
    
37. [    0.080000] Mount-cache hash table entries: 512
    
38. [    0.090000] NET: Registered protocol family 16
    
39. [    0.090000] MIPS: machine is TP-LINK TL-WR703N v1
    
40. [    0.330000] bio: create slab <bio-0> at 0
    
41. [    0.340000] Switching to clocksource MIPS
    
42. [    0.350000] NET: Registered protocol family 2
    
43. [    0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    
44. [    0.350000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
    
45. [    0.360000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
    
46. [    0.360000] TCP: Hash tables configured (established 1024 bind 1024)
    
47. [    0.370000] TCP reno registered
    
48. [    0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
    
49. [    0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
    
50. [    0.380000] NET: Registered protocol family 1
    
51. [    0.390000] PCI: CLS 0 bytes, default 32
    
52. [    0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    
53. [    0.410000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
    
54. [    0.420000] msgmni has been set to 57
    
55. [    0.430000] io scheduler noop registered
    
56. [    0.430000] io scheduler deadline registered (default)
    
57. [    0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
    
58. [    0.440000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
    
59. [    0.450000] console [ttyATH0] enabled, bootconsole disabled
    
60. [    0.460000] m25p80 spi0.0: found en25q32b, expected m25p80
    
61. [    0.470000] m25p80 spi0.0: en25q32b (4096 Kbytes)
    
62. [    0.470000] 5 tp-link partitions found on MTD device spi0.0
    
63. [    0.480000] Creating 5 MTD partitions on "spi0.0":
    
64. [    0.480000] 0x000000000000-0x000000020000 : "u-boot"
    
65. [    0.490000] 0x000000020000-0x0000000fe1b8 : "kernel"
    
66. [    0.490000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
    
67. [    0.500000] 0x0000000fe1b8-0x0000003f0000 : "rootfs"
    
68. [    0.510000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
    
69. [    0.520000] mtd: partition "rootfs" set to be root filesystem
    
70. [    0.530000] mtd: partition "rootfs_data" created automatically, ofs=3A0000, len=50000
    
71. [    0.530000] 0x0000003a0000-0x0000003f0000 : "rootfs_data"
    
72. [    0.540000] 0x0000003f0000-0x000000400000 : "art"
    
73. [    0.550000] 0x000000020000-0x0000003f0000 : "firmware"
    
74. [    0.800000] ag71xx_mdio: probed
    
75. [    0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
    
76. [    1.410000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
    
77. [    1.410000] TCP westwood registered
    
78. [    1.420000] NET: Registered protocol family 17
    
79. [    1.420000] 8021q: 802.1Q VLAN Support v1.8
    
80. [    1.430000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
    
81. [    1.440000] Freeing unused kernel memory: 192k freed
    
82. [    3.500000] Registered led device: tp-link:blue:system
    
83. [    6.770000] eth0: link up (10Mbps/Half duplex)
    
84. [    6.800000] JFFS2 notice: (403) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 9 of xref (0 dead, 2 orphan) found.
    
85. [    7.500000] SCSI subsystem initialized
    
86. [    7.680000] usbcore: registered new interface driver usbfs
    
87. [    7.680000] usbcore: registered new interface driver hub
    
88. [    7.690000] usbcore: registered new device driver usb
    
89. [    8.180000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    
90. [    8.190000] ath79-ehci ar933x-ehci: Atheros built-in EHCI controller
    
91. [    8.190000] ath79-ehci ar933x-ehci: new USB bus registered, assigned bus number 1
    
92. [    8.230000] ath79-ehci ar933x-ehci: irq 3, io mem 0x1b000000
    
93. [    8.250000] ath79-ehci ar933x-ehci: USB 2.0 started, EHCI 1.00
    
94. [    8.250000] hub 1-0:1.0: USB hub found
    
95. [    8.250000] hub 1-0:1.0: 1 port detected
    
96. [    8.370000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    
97. [    8.490000] uhci_hcd: USB Universal Host Controller Interface driver
    
98. [    8.610000] Initializing USB Mass Storage driver...
    
99. [    8.610000] usbcore: registered new interface driver usb-storage
    
100. [    8.620000] USB Mass Storage support registered.
     
101. 
     

复制代码

可忙BB

1. [   29.030000] eth0: link down
   
2. [   29.550000] Compat-wireless backport release: compat-wireless-2012-02-27-1-r31201
   
3. [   29.550000] Backport based on wireless-testing.git master-2012-02-27
   
4. [   29.670000] cfg80211: Calling CRDA to update world regulatory domain
   
5. [   30.100000] cfg80211: World regulatory domain updated:
   
6. [   30.110000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
   
7. [   30.110000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
   
8. [   30.120000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
   
9. [   30.130000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
   
10. [   30.140000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    
11. [   30.140000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    
12. [   30.730000] ath: EEPROM regdomain: 0x0
    
13. [   30.730000] ath: EEPROM indicates default country code should be used
    
14. [   30.730000] ath: doing EEPROM country->regdmn map search
    
15. [   30.730000] ath: country maps to regdmn code: 0x3a
    
16. [   30.730000] ath: Country alpha2 being used: US
    
17. [   30.730000] ath: Regpair used: 0x3a
    
18. [   30.730000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
    
19. [   30.730000] Registered led device: ath9k-phy0
    
20. [   30.730000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
    
21. [   30.740000] cfg80211: Calling CRDA for country: US
    
22. [   30.810000] cfg80211: Regulatory domain changed to country: US
    
23. [   30.820000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    
24. [   30.820000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
    
25. [   30.830000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
    
26. [   30.840000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    
27. [   30.850000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    
28. [   30.850000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    
29. [   30.860000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
    
30. [   30.920000] NTFS driver 2.1.30 [Flags: R/O MODULE].
    
31. [   31.400000] PPP generic driver version 2.4.2
    
32. [   31.660000] ip_tables: (C) 2000-2006 Netfilter Core Team
    
33. [   31.890000] NET: Registered protocol family 24
    
34. [   31.960000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
    
35. [   32.740000] usbcore: registered new interface driver ums-alauda
    
36. [   32.760000] usbcore: registered new interface driver ums-cypress
    
37. [   32.780000] usbcore: registered new interface driver ums-datafab
    
38. [   32.800000] usbcore: registered new interface driver ums-freecom
    
39. [   32.810000] usbcore: registered new interface driver ums-isd200
    
40. [   32.830000] usbcore: registered new interface driver ums-jumpshot
    
41. [   32.850000] usbcore: registered new interface driver ums-karma
    
42. [   32.980000] usbcore: registered new interface driver ums-sddr09
    
43. [   33.000000] usbcore: registered new interface driver ums-sddr55
    
44. [   33.020000] usbcore: registered new interface driver ums-usbat
    
45. [   35.040000] device wlan0 entered promiscuous mode
    
46. [   37.280000] device wlan0 left promiscuous mode
    
47. [   37.280000] br-lan: port 1(wlan0) entering disabled state
    
48. [   37.550000] device wlan0 entered promiscuous mode
    
49. [   41.310000] device eth0 entered promiscuous mode
    
50. [   41.600000] eth0: link up (10Mbps/Half duplex)
    
51. [   43.000000] br-lan: port 2(eth0) entering forwarding state
    
52. [   43.000000] br-lan: port 2(eth0) entering forwarding state
    
53. [   43.010000] br-lan: port 1(wlan0) entering forwarding state
    
54. [   43.020000] br-lan: port 1(wlan0) entering forwarding state
    
55. [   58.040000] br-lan: port 2(eth0) entering forwarding state
    
56. [   58.040000] br-lan: port 1(wlan0) entering forwarding state
    
57. [   83.830000] usb 1-1: new high-speed USB device number 2 using ath79-ehci
    
58. [   84.120000] eth0: link down
    
59. [   84.120000] br-lan: port 2(eth0) entering forwarding state
    
60. [   84.250000] scsi0 : usb-storage 1-1:1.0
    
61. [   85.250000] scsi 0:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
    
62. [   85.900000] sd 0:0:0:0: [sda] 3862528 512-byte logical blocks: (1.97 GB/1.84 GiB)
    
63. [   85.900000] sd 0:0:0:0: [sda] Write Protect is off
    
64. [   85.910000] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
    
65. [   85.910000] sd 0:0:0:0: [sda] No Caching mode page present
    
66. [   85.910000] sd 0:0:0:0: [sda] Assuming drive cache: write through
    
67. [   85.930000] sd 0:0:0:0: [sda] No Caching mode page present
    
68. [   85.930000] sd 0:0:0:0: [sda] Assuming drive cache: write through
    
69. [   85.940000]  sda: sda1 sda2
    
70. [   85.950000] sd 0:0:0:0: [sda] No Caching mode page present
    
71. [   85.950000] sd 0:0:0:0: [sda] Assuming drive cache: write through
    
72. [   85.960000] sd 0:0:0:0: [sda] Attached SCSI removable disk
    
73. [   94.200000] eth0: link up (10Mbps/Half duplex)
    
74. [   94.200000] br-lan: port 2(eth0) entering forwarding state
    
75. [   94.200000] br-lan: port 2(eth0) entering forwarding state
    
76. [  109.240000] br-lan: port 2(eth0) entering forwarding state

复制代码

可忙BB

芯片是 Atheros AR9330 rev 1
型号被刷成 TL-WR703N 了
内存怎么看？？

可忙BB

似乎有点不妙art.bin没了？刷没了？

可忙BB

mac地址也有啊？？

可忙BB

已经备份成功了？？ 莫名其妙啊。刷完Luci测试一下无线吧。




后语、无线没问题

可忙BB

贴个图，请高手指导。

可忙BB

已安装文件信息；

1. /$ opkg list-installed
   
2. base-files - 104-r31201
   
3. base-files-network - 4
   
4. blkid - 1.42-1
   
5. block-mount - 0.2.0-8
   
6. busybox - 1.19.4-1
   
7. crda - 1.1.2-1
   
8. ddns-scripts - 1.0.0-19
   
9. dnsmasq - 2.59-3
   
10. dropbear - 2011.54-2
    
11. firewall - 2-49
    
12. hotplug2 - 1.0-beta-4
    
13. iptables - 1.4.10-4
    
14. iw - 3.3-1
    
15. kernel - 3.2.13-1-c133eb87cc3366ef1abadadddee761a4
    
16. kmod-ath - 3.2.13+2012-02-27-1
    
17. kmod-ath9k - 3.2.13+2012-02-27-1
    
18. kmod-ath9k-common - 3.2.13+2012-02-27-1
    
19. kmod-cfg80211 - 3.2.13+2012-02-27-1
    
20. kmod-crypto-aes - 3.2.13-1
    
21. kmod-crypto-arc4 - 3.2.13-1
    
22. kmod-crypto-core - 3.2.13-1
    
23. kmod-fs-ext4 - 3.2.13-1
    
24. kmod-fs-ntfs - 3.2.13-1
    
25. kmod-fs-vfat - 3.2.13-1
    
26. kmod-gpio-button-hotplug - 3.2.13-1
    
27. kmod-ipt-conntrack - 3.2.13-1
    
28. kmod-ipt-core - 3.2.13-1
    
29. kmod-ipt-nat - 3.2.13-1
    
30. kmod-ipt-nathelper - 3.2.13-1
    
31. kmod-leds-gpio - 3.2.13-1
    
32. kmod-ledtrig-default-on - 3.2.13-1
    
33. kmod-ledtrig-netdev - 3.2.13-1
    
34. kmod-ledtrig-timer - 3.2.13-1
    
35. kmod-lib-crc-ccitt - 3.2.13-1
    
36. kmod-lib-crc16 - 3.2.13-1
    
37. kmod-mac80211 - 3.2.13+2012-02-27-1
    
38. kmod-nls-base - 3.2.13-1
    
39. kmod-nls-cp437 - 3.2.13-1
    
40. kmod-nls-iso8859-1 - 3.2.13-1
    
41. kmod-nls-iso8859-2 - 3.2.13-1
    
42. kmod-nls-utf8 - 3.2.13-1
    
43. kmod-ppp - 3.2.13-1
    
44. kmod-pppoe - 3.2.13-1
    
45. kmod-scsi-core - 3.2.13-1
    
46. kmod-usb-core - 3.2.13-1
    
47. kmod-usb-ohci - 3.2.13-1
    
48. kmod-usb-storage - 3.2.13-1
    
49. kmod-usb-storage-extras - 3.2.13-1
    
50. kmod-usb-uhci - 3.2.13-1
    
51. kmod-usb2 - 3.2.13-1
    
52. kmod-wdt-ath79 - 3.2.13-1
    
53. libblkid - 1.42-1
    
54. libc - 0.9.33-104
    
55. libcom_err - 1.42-1
    
56. libcurl - 7.23.1-1
    
57. libevent2 - 2.0.16-1
    
58. libext2fs - 1.42-1
    
59. libgcc - 4.6-linaro-104
    
60. libip4tc - 1.4.10-4
    
61. libminiupnpc - 1.6-1
    
62. libnl-tiny - 0.1-3
    
63. libopenssl - 1.0.1-1
    
64. libpthread - 0.9.33-104
    
65. librt - 0.9.33-104
    
66. libuci - 2012-03-28.1-1
    
67. libuuid - 1.42-1
    
68. libxtables - 1.4.10-4
    
69. mtd - 17
    
70. opkg - 618-2
    
71. ppp - 2.4.5-4
    
72. ppp-mod-pppoe - 2.4.5-4
    
73. swap-utils - 2.13.0.1-4
    
74. swconfig - 10
    
75. transmission-daemon - 2.50-2
    
76. uboot-envtools - 2011.06-4
    
77. uci - 2012-03-28.1-1
    
78. vsftpd - 2.3.4-4
    
79. wireless-tools - 29-4
    
80. wpad-mini - 20120326-1
    
81. zlib - 1.2.5-1
    

复制代码

可忙BB

查看挂载设备：

1. /$  ls /dev
   
2. 1-1
   
3. console
   
4. full
   
5. kmsg
   
6. log
   
7. mem
   
8. mtd0
   
9. mtd0ro
   
10. mtd1
    
11. mtd1ro
    
12. mtd2
    
13. mtd2ro
    
14. mtd3
    
15. mtd3ro
    
16. mtd4
    
17. mtd4ro
    
18. mtd5
    
19. mtd5ro
    
20. mtdblock0
    
21. mtdblock1
    
22. mtdblock2
    
23. mtdblock3
    
24. mtdblock4
    
25. mtdblock5
    
26. null
    
27. port
    
28. ppp
    
29. ptmx
    
30. pts
    
31. random
    
32. sda
    
33. sda1
    
34. sda2
    
35. shm
    
36. tty
    
37. ttyATH0
    
38. ttyS0
    
39. urandom
    
40. usb1
    
41. watchdog
    
42. zero
    

复制代码

可忙BB

sda
sda1
sda2

我挂的是读卡器，tf卡分两区。看来是认出来了。

可忙BB

一切都白费。 ”wam/lan“口可用“lan”   “lan”口无效

配置文件的问题？？？

参考db120的弄一下试试。

1. [code]config 'interface' 'lan'
   
2.         option 'type' 'bridge'
   
3.         option 'ifname' 'eth1.1'
   
4.         option 'proto' 'static'
   
5.         option 'ipaddr' '192.168.1.1'
   
6.         option 'netmask' '255.255.255.0'
   
7.         option 'nat' '1'
   
8. 
   
9. config 'interface' 'wan'
   
10.         option 'ifname' 'eth1.2'
    
11.         option 'proto' 'dhcp'
    
12. 
    
13. config 'switch' 'eth1'
    
14.         option  'reset' '1'
    
15.         option  'enable_vlan'   '1'
    
16. 
    
17. config  'switch_vlan'
    
18.         option  'device'        'eth1'
    
19.         option  'vlan'  '1'
    
20.         option  'ports' '0 1 2 5*'
    
21. 
    
22. config  'switch_vlan'
    
23.         option  'device'        'eth1'
    
24.         option  'vlan'  '2'
    
25.         option  'ports' '3 4 5*'

复制代码

可忙BB

我疯了，看来真是起点高了。 决定刷楼主的固件，再试。

可忙BB

只有eth0，怎么搞？？？？？
我无能啊，搞不下去了。

antclan

/etc/config/network , 没ttl的话（或者说在没有“无ttl救砖”经验的情况下），不要乱改，小心变砖。
先把reset恢复出厂设置配好，再弄。

可忙BB

antclan 发表于 2012-7-5 11:07
/etc/config/network , 没ttl的话（或者说在没有“无ttl救砖”经验的情况下），不要乱改，小心变砖。
先把 ...

已经砖了一回，firstboot回来了。没有eth1怎么办？需要固件编辑器吗？真的不会Ubuntu啊。没有下一步的方向了。